Studio Equipment charts

Notes: Modulated digital reverb with an analogue dry signal path, the clock control lets you adjust the core frequency of the DSP, creating a smooth pitch shift in time, allowing you to create from a sharp traditional plate-like reverb to an underworld cavernous ambience.

Dedicated sustain footswitch to create an infinite modulated ambience, trails option to combine momentary activation and be able to add lush movement at any time.

Soft footswitch bypass latch & momentary
2 Modulation depths (off @ center position) MOD toggle
DSP clock control for deep cavernous textures
Trails toggle
2nd delay line with analog feedback
Pre-delay
Damp control
Infinite sustain footswitch
Top mounted jacks

Notes: The Shifty is essentially a combination of four sample and hold stages, a sequential gate and sequencer controller. This collection of functions allows for some specific and useful utility application.

One of the primary uses for Shifty is to take a monophonic sequence source and route each new note of the sequence to up to four different synthesizer voices in a specific pattern. In this way you can create pseudo polyphonic sequences since each voice can be triggered to play and sustain while the next voice int the sequence gets triggered. Another term for this is hocketing.

The other main application of the Shifty is to function as an Analog Shift Register. In this mode each new gate input received causes the current set of pitches to be shifted to new output locations as a new one is added and the oldest one is replaced. This can be an interesting way to create chords that are up to four stacked notes when used with a pitch sequence source that has a harmonious series of notes (e.g. a pentatonic scale works really well). Even just using two of the outputs will yield very interesting melodic interplay and is an excellent way to make a simple sequence much more complex and interesting.

In a more basic way the Shifty could be used as a simple Sample/Track and Hold module or as a sequential gate.

Notes: A Producer looking for a professional, durable case solution for the Universal Audio Volt 1/ 2? Then look no further, UDG developed a super light EVA Hardcase designed for life on the road. Constructed from durable lightweight compression moulded EVA material with a laminated nylon exterior this case provides protection against drops, scratches & liquids. Skillfully designed & moulded to fit the Universal Audio Volt 1/ 2, this case is perfect for the travelling Producer that needs to protect their equipment.

Specifications

Weight: 0,40 kg / 0.88 lbs

Colour: Black
Outer Dimensions (W x H x D) 20.0 x 14.7 x 6.3 cm | 7.9 x 5.8 x 2.5 inch
Inner Dimensions (W x H x D) 19.0 x 13.7 x 5.3 cm | 7.5 x 5.4 x 2.1 inch
Material: Durashock molded EVA foam
Protection: Cover main material 600D polyester with 5 mm EVA durashock molded body
Water repellent laminated nylon exterior
Black soft fleece interior
Protective top removable foam

Extras

Removable divider for extra cables or power adapter
Heavy duty handle
Easy grip zipper pulls

Fits

Universal Audio Volt 1 or Volt 2, power adapter, extra cables

Notes: The next generation of Ableton Live controller from Akai, the APC64 is designed for seamless integration with the software, or as a standalone step sequencer and controller. The 64 velocity sensitive pads handle playing, recording, clip launching, sequencing and much more, while eight assignable touch strips offer extensive hands-on control.

Supplier's notes:

APC64; Next generation Ableton live controller.

Touch the future

Leap into a new world of musical possibility in the studio, on stage, and anywhere creativity leads you with the powerful APC64.

Ableton live controller; with sequencer and touchstrips

The new Akai Professional APC64 is a powerful next-generation Ableton Live controller for studio and live performance.

It features 64 RGB velocity-sensitive pads with poly aftertouch, and 8 fully assignable Touch Strips for instant hands-on control of devices, pitch, modulation, and much more. APC64 also works as a standalone 32-step 8-track Step Sequencer and controller with 3 MIDI ports and 8 CV/Gate outputs to take full control of synths, drum machines, or modular rack devices.

In-depth control of Ableton Live

Enter the matrix

APC64 features a vibrant 8x8 pad matrix of 64 velocity-sensitive RGB pads with poly aftertouch for playing chords, synth leads, Ableton Live's Drum Racks and of course launching Clips in Session View.

Touch the future

Add a whole new level of expression and control to your music production and live performances with 8 fully assignable Touch Strips with RGB LED indicators. Get control of Ableton Live's devices - including Auto Filter, Delay, Reverb, Impulse, Simpler and more - right at your fingertips. Adjust macros, mixer volume, pan, and effects sends as well as writing automation.

Visual feedback and control

APC64 includes a smart colour LED screen with a fast push encoder for real-time visual feedback of your parameters. Move around Ableton Live's devices and mixing environments while keeping track of each parameter on the screen. APC64 also features dedicated transport control with Play, Stop, and Record for capturing your ideas along with 8 Track Mute and Solo buttons for mixing and live performance.

Standalone step sequencing

APC64 features an internal 32-step 8-track Step Sequencer enabling completely DAW-less control of your favourite synths. With 8 CV/Gate outputs and 3 1/8" MIDI ports, you can connect, sequence, and capture your favourite modular racks, keyboards, classic drum machines, and more. Add continuous control and expression using the 8 Touch Strips for a whole new level of performance. Apply additional creative dimensions to MIDI notes using the Probability, Velocity, and Mutate functions for further experimentation.

Powerful production and performance

APC64 facilitates a seamless workflow within Ableton Live; from triggering samples and loops in Ableton Live's Drum Rack, all the way to writing expressive melodies using the Notes, Scale, and Chord modes. Use the onboard Step Sequencer to generate inventive melodic patterns that can be instantly transferred to Ableton Live using the Send To Clip function. Apply swing and quantize to your beats or use APC64 to arm and record vocal tracks directly in Ableton Live sessions.

Ableton drum rack/simpler control

APC64 features a dedicated Drum Mode allowing you to play and record beats, loops, and slices using an Ableton Live Drum Rack or Simpler device. Capture additional inspiration using the 8 Touch Strips to control Ableton Live's FX racks during beat making and performance.

Included software bundle

Ableton Live Lite 11

APC64 Includes Ableton 11 Lite for all your software music production needs in one package to produce, perform, arrange, record, edit, mix and master your music. Live Lite includes sounds, instruments, and sequencing, recording, and arranging capabilities.

Air music instruments/plugins

APC64 Includes a collection of professional plug-in instruments and effects so you can start producing out of the box. Included are the following plugins: TubeSynth, Electric, Ether, Halfspeed, Vocal Tuner, Flavor, and the Sonivox Essential Keyboard Collection.

Custom editor software

Create your own custom layouts with the included desktop software editor for Mac/PC to personalize and store pre-sets for quick recall in standalone.

Key specs

Display
Graphical full colour LCD
Connections: USB-C, 8x 1/8" (3.5 mm) CV/Gate, 2x 1/8" (3.5 mm) MIDI Output, 1x 1/8" (3.5 mm) MIDI Input
Dimensions (width x depth x height): 10.7" x 14.6" x 1.4" 272 x 371 x 34.5 mm
Weight: 3.5 lb/1.6 kg

Notes: Audio Optimized USB-C to USB-B Cables

56kO pull-up resistor to protect your devices
Dual slimline ferrites prevent signal dropouts
High quality connectors ensure long cable life
Works with all USB-B devices

Ideal for home and professional use where impeccable audio is a must, Chroma Cables complement the modern DJ and music production technology with a streamlined styling that keeps your setup looking fresh and sleek. All cables are not created equal, and ours are engineered from scratch for digital performers, by digital performers.

Noise-Filtering Features

Each cable has two ferrite core chokes, one at each end of the cable. Paired with fully-braided shielding, Chroma Cables do a great job of eliminating interference along the signal path - making these the best USB cables for DJs.

No More Adapters

Forget about tiny adapters that can easily get lost in a dark booth. These high quality USB-C cables ensure that all your audio and MIDI devices have a reliable connection with no compromises.

Always Strapped

Even after placing your cables neatly in your bag, it's easy to wind up with a tangled clump of cables. The built-in velcro cable strap helps prevent this, keeping your gig bag nice and tidy. You'll wonder how you managed without this.

Compatibility Notes:

Works with all* USB devices with a USB type B connector but it's worth checking for obstructions if you plan on ordering an angled cable.

*Please note that the right angle cable won't work with a Kontrol D2, S2, S4, S5, S8, or Z1 or Traktor Audio 10 while using the power supply.

Size + Weight:
Length: 59.05" / 150cm
Weight: 0.18lb / 0.08kg"

Notes: Test your modules safely without reaching into your case! The TST has two keyed 16-pin headers on the front of the module so you can plug and unplug quickly and easily. Two 16-pin plugs are included to shield the power pins when the module is not in use. It also has LEDs to indicate the power status on each rail.

Please note: Use this module at your own risk. You will be exposing electricity to the front of your modular system. Be careful not to dangle patch-cables, etc. on the exposed pins. This may damage modules and your power supply. Be smart and safe!

Features and Specifications:
Two 16-pin connectors and plugs on the front side of the module
LED indicator for each rail
Module width: 3HP
Module depth: 5mm
Current draw:
+12V: 1mA
-12V: 1mA
+5V: 1mA
Includes keyed power cable, 2.5mm and 3mm screws

Notes: HN VCF is a state variable filter having 12 db Low Pass, 12 dB High Pass, 6 dB Band Pass plus 18 db Low Pass marked as "LP!", because it has extra drive. All three parameters: "Freq", "Resonance" and "Drive" have dual knobs with outer knobs controlling bipolar CV amount. These affected CVs are then shown by the relative green/blue LEDs.

The possibility to have CV over "Resonance" and "Drives" makes it a very capable 6 HP filter.

"LP!" output has 6 dB steeper slope (18 dB) compared to ordinary 12 dB "LP" output. Plus it has much more drive.

Dimensions
6 HP
35 mm deep

Current Draw
55 mA +12V
65 mA -12V

Notes: Pack of high Quality patch cables. Not too stiff, not too loose!

One colour for each size make Befaco patch cables just perfect to keep them organized!

This pack contains 6 high quality purple patch cables.

Notes: Set of 5 high-quality braided & soft 3.5mm patch cables for use with eurorack modules. The braided patch cables have a soft touch & are perfect for traveling with your eurorack system patched as they are super-bendable and much less likely to get tangled even with your case lid closed. Pleasant & practical for a better patching experience.

Notes: NANOPATCH M is a tiny and incredibly versatile patch bay, with mini jacks sockets on both the rear and the top panel. It is ideal for connecting to instruments and a mixer when used in conjunction with NANOPATCH X.

It also works with CV, so can be used as a breakout box for semi-modular synths with outputs in hard-to-reach places (e.g. Moog Grandmother) and devices that output CV over TRS sockets (e.g. MPC ONE).

Dimensions: 76 mm x 70 mm x 22 mm (not including sockets and feet)

Mini jack sockets on the back panel makes it easy to connect to eurorack systems and small instruments such as Korg Volcas.

3.5 mm to 6.35 mm cables can be used when connecting to equipment with 1/4" sockets.

Using standard eurorack cables, easily patch signals from a NANOPATCH M through effects connected to a NANOPATCH X (and back again).

How It Works

Rear sockets labelled 1/2, 3/4, 5/6 and 7/8 can be used for either mono or stereo signals. For example, if a TRS cable is plugged into rear socket 1/2, the left and right channels will break out to sockets 1 and 2 on the top panel. If another cable is plugged into rear socket 2, rear sockets 1 and 2 will correspond to sockets 1 and 2 on the top panel, both in mono.

Normalling

Channels 1-4 can be full-normalled to channels 5-8 using DIP switches located on the side of the NANOPATCH M.

This allows a signal to pass through from instrument to mixer without the need for any patching. When a patch cable is inserted into either socket of a normalled pair, the connection is broken, allowing for custom routing of the signal.

Typical Setup

A typical setup would be to have four instruments connected to channels 1-4 and four mixer channels connected to channels 5-8.

Connections to the mixer could either be made with four separate mono cables (utilizing the sockets on the side) or with two insert cables (as in the diagram).

Notes: The Roland SPD-SX Pro, with its forefront sampling capabilities and performance attributes, has not merely cemented itself as an indispensable apparatus for electronic drummers and percussionists but has also emerged as one of the most ardently requested and sought-after Decksaver covers.
In acknowledgement of this considerable demand, Decksaver are delighted to present the Decksaver cover for the Roland SPD-SX Pro, meticulously fashioned from premium polycarbonate. This material is chosen for its outstanding durability and protective qualities, guaranteeing your instrument is defended against dust, spills, and even significant accidental impacts.

Custom-designed to fit the SPD-SX Pro precisely, this cover encases every pad, button, and control, whilst ensuring trouble-free access to all essential connections. The design has been thoroughly devised with the artist's requirements in mind, facilitating swift and straightforward application or removal. This proves particularly advantageous for performers and studio professionals who necessitate efficiency in both the setup and dismantling processes. Whether you're on tour, in the recording studio, or merely storing your SPD-SX Pro at home, this cover acts as a dependable shield, protecting your instrument's sensitive components from the rigours of its environment.

Opting for the highly sought-after Decksaver cover for your Roland SPD-SX Pro transcends a mere practical choice; it symbolises a commitment to maintaining the integrity and longevity of your instrument. It represents an essential investment for any musician dedicated to safeguarding their Roland SPD-SX Pro, ensuring it remains in peak condition for every performance and creative endeavour.

Weight: 0.461 kg
Length: 36.6 cm
Width: 33.9 cm
Height: 4.3 cm

Material: Smoked clear polycarbonate.

WARNING: When your Decksaver cover is in place, please ensure that your equipment is kept away from direct and high heat sources, such as radiators, fires and sunlight.

Notes: The PreSonus FaderPort 16, renowned for its expansive 16-channel control interface and its enhancement of mixing efficiency, has become a pivotal tool for audio professionals worldwide. In direct response to its widespread acclaim and the growing need for dedicated protection, Decksaver are excited to present the Decksaver cover for the PreSonus FaderPort 16. This cover, constructed from durable polycarbonate, is expertly fashioned to shield your FaderPort 16 from dust, accidental spills, and impacts, ensuring your gear remains in top-notch condition.

This Decksaver cover is precision-crafted to fit the PreSonus FaderPort 16 perfectly, enveloping each of its 16 faders, buttons, and knobs, while thoughtfully allowing space for all essential connections. This meticulous design is born from an understanding of the dynamic needs of today's audio professionals, facilitating a hassle-free experience for quick setups and breakdowns. Ideal for the bustling studio environment, the home setup, or during transport, this cover provides a robust layer of protection, preserving the operational integrity and aesthetics of your FaderPort 16.

Choosing this Decksaver cover for your PreSonus FaderPort 16 goes beyond practicality; it represents a commitment to safeguarding a key component of your studio setup. Highly requested by users and endorsed by experts in the industry, this cover is essential for those who prioritize the care and longevity of their PreSonus FaderPort 16, ensuring it's always ready for any mixing challenge or creative session.

Weight: 0.365 kg
Length: 37.7 cm
Width: 27.5 cm
Height: 2.7 cm

Material: Smoked clear polycarbonate.

WARNING: When your Decksaver cover is in place, please ensure that your equipment is kept away from direct and high heat sources, such as radiators, fires and sunlight.

Notes: Another update for WMD's clever dual VCA, this time a little bigger to give more control. Digital control of CV and attenuation gives lots of creative options. Third time's a charm.

Supplier's Notes:
WMD have done several designs of this circuit over the years, the first one had no knobs, the second was too small, the MKIII is finally how this circuit should be packaged. This module does some really cool stuff and is super useful in any system.

The Digital VCA lets signal through like a normal VCA, but the CV and attenuation level is controlled digitally. This lets us do things like wait until there is a zero crossing to change the amplitude, resulting in clickless amplitude changes.

The Trigger mode causes the VCA to only update when a trigger is received. The addition of a noise circuit for each side let us do a very quick and easy sample and hold that never droops. With no input, 5V is normaled to the attenuator, so you get a 0-5V sample and hold. In Bipolar mode, you can get -5 to +5V.

Both sides have bipolar VCA mode (polarizer), which lets them invert the signal when negative CV comes in. Also known as ring modulation. With the zero crossing detector, this can produce some super wild wave shapes.

Features

Dual VCA Design
Unipolar or Bipolar Operation
DC Coupled Analogue Signal Path
Low Distortion / Low Noise
VCA Closes Completely
Zero Crossing Detector Mode
Trigger Mode
Two Independent Noise Sources
8 bit CV resolution
Great for Fast Envelopes and Sine Bass Sounds

Specifications

Power: +65mA, -45mA
Width: 8HP
Depth: 35mm with cables
Height: Eurorack 3U (128.5mm)
Board Height Behind Panel: 112mm
CV/Signal Input Impedance: 100k
Output Impedance: 1k
UPD in 3.3V Threshold Schmitt Trigger
ZCD produces 15us 5V pulse
5V CV to fully open VCA
Linear VCA response
20Vpp signal handling

Notes: NI's more affordable Komplete Kontrol A range offers a keenly priced take on the flagship S models. Here in 49-key format, the semi-weighted keybed offers great feel.

Supplier's notes:
Get hands-on with your music:

Music-making is at its best when it's fast, fun, and physical. Find the right sound, make it your own, perform, and capture the results - all from a responsive, semi-weighted keyboard. Complete with four premium instruments plus MASCHINE Essentials, A-Series keyboards come with everything you need to bring your ideas to life.

Find your sounds faster:

With hundreds of presets to choose from, finding the right sound can be a chore. With KOMPLETE KONTROL, however, all of your KOMPLETE and NKS presets are intuitively tagged and organised, so finding the right one is fast and easy. What's more, you can hear a preview of each sound as you browse, without loading individual instruments.

Need some serious low end? Use the encoders and OLED display to select SYNTH > BASS > SUB BASS, then listen through the presets and load up the right one for your track.

Pre-mapped and ready to play:

All of your KOMPLETE and NKS instruments and effects are pre-mapped to the KOMPLETE KONTROL hardware by the people who know them best - the instrument designers themselves. Essential parameters like envelope controls and filter cutoffs are instantly displayed on the OLED display as you touch the corresponding knob. That means you can see exactly what you're adjusting in real time - whether it's in kHz, dB, or BPM.

Perform creatively:

With Smart Play, you never need to worry about hitting a wrong note - just pick a scale and play. Activate chord mode to create a rich progression by playing single keys, then switch on the arpeggiator and turn it into an expressive musical performance. And for keyboard novices, Easy Mode maps the white keys to whichever scale you like.

Capture your ideas:

No matter your setup, A-Series is designed to fit right into your existing workflow, with immediate access to transport, mixing, and editing controls in your favourite DAW. Logic Pro X and GarageBand are currently supported, with advanced integration for Ableton Live, Cubase, and Nuendo coming soon after launch. And if you're just getting started, the included MASCHINE Essentials allows you to capture and arrange your ideas direct from your hardware - no additional software needed.

Instruments included:

With more than 4,500 sounds and 9.7 GB of content included, A-Series keyboards come with everything you need to start making music. Register your hardware and get two powerful synths, two meticulously sampled pianos, and more. Plus with MASCHINE Essentials, you'll have all the tools you need to go from inspiration to finished track.

Notes: We have reissued the original Version 1 Big Muff and it's dripping with vintage Electro-Harmonix DNA and tone. Dubbed the Triangle Big Muff because of the layout of its Volume, Sustain and Tone controls, this is the one that started it all. The new Triangle Big Muff is a faithful re-creation of the original circa 1969 circuit now housed in a pedalboard friendly, die cast chassis.

Electro-Harmonix founder, Mike Matthews, stated: "The Big Muff Pi is the pedal we are best known for so I wanted to commemorate EHX's 50th Anniversary (1968-2018) by re-releasing V1, the very first Big Muff. Original pedals are now selling for hundreds of dollars and this reissue absolutely nails that creamy, violin-like sustain and musical tone at a price a working musician can afford.

Notes: A spacious backpack that accommodates a compact synthesizer, new from SEQUENZ.

Three storage compartments are included for various purposes. The main compartment can accommodate a larger portable equipment, such as a compact synthesizer, effect board, or DJ controller.

The second compartment has enough space to hold up to a 17-inch laptop computer. Inside are organizer pockets that can store a smartphone, cables, or a wallet, so you can carry all of your daily necessities.

The front pocket is a sleeve equipped with fasteners, ideal for holding books, magazines, or sheet music.

Thick padding securely protects your equipment and computer. A U-shaped shoulder belt distributes the weight of the pack, and the back and shoulder areas use mesh material for cushioning and cooling, letting you carry heavy equipment with ease.

MP-TB1 is a stylish backpack that holds everything you need effortlessly.

Notes: Pack of three, six-way, Befaco-branded multiples with six 3.5mm inputs.

Notes: The MOD REX is a kinetic tour-de-force that lets you weave compelling, shifting, musical tapestries. Whether you are a guitarist, synthesist or electronic musician you will find it inspires your creativity and stretches your musical boundaries.

Four independent modulation sections:

The heart of the pedal is its four, independent modulation sections synced in time, they are:

MOD features great sounding EHX Vibrato, Flanger, Chorus or Phaser. The Depth knob lets you set the amount of the effect while Feedback controls the resonance of the Flanger and Phaser.

TREM delivers tremolo, an effect that modulates the volume of your signal. The Depth control sets tremolo intensity.

PAN modulates between left and right in stereo operation. In mono operation the PAN section acts as another tremolo section, but with the wave shapes all inverted!

FILTER offers a choice of a modulated LPF, HPF or BPF. In LPF (low pass filter) frequencies above a modulated cut-off point are cut. In HPF (high pass filter) frequencies below a modulated cut-off point are cut, and in BPF (band pass filter) frequencies above and below a modulated centre point are cut.

Each section also features a choice of four LFO shape options: rising sawtooth, triangle, falling sawtooth or square wave. They affect the way the modulation transitions and provide advanced creative control over the specific section as well as the way they interact with each other.

Tempo control that's flexible and powerful:

The MOD REX delivers virtually limitless polyrhythmic possibilities.

Its TEMPO component gives you nine note-length choices for each of the four modulation sections. They are independently selectable in increments starting at a whole note and ranging thru subdivisions that go up to a 16th note. In addition, any of the sections can be bypassed.

The MOD REX's tempo (displayed as beats per minute or BPM) is adjustable with the Tempo knob, Tap Tempo footswitch or by using an expression pedal into its EXP input. It can also be synced to an external device with MIDI Clock or an external pulse clock.

MIDI and the MOD REX:

The pedal's robust MIDI implementation enables you to sync devices quickly and easily as well as automate functions and changes so they occur precisely when and where you want them whether you are working at home, in a studio or live.

The MOD REX accepts MIDI to enable it to tempo sync the modulation rate with an external device, to recall presets via MIDI Program Change messages and to control any parameter on the MOD REX via Control Change messages.

Extras:

The MOD REX lets you save and recall up to 100 presets. It comes from the factory with 20 great programs.

The pedal features full stereo input and output.

An external foot controller input makes banking up and down thru presets quick and easy.

Notes: 3.5 mm Stereo jack plug to 2 x 3.5 mm right angled jack plugs. Loose, 1 m.

Notes: Stereo jack to jack lead, 0.23m length.

Notes: Standard 3.5mm Stereo jack to jack lead with screened cable.

Notes: Standard 3.5mm Stereo jack to jack lead with screened cable.

Notes: Standard 3.5 mm stereo jack plug to 3.5 mm stereo jack socket lead.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod20 is 20HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod20 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: This 30HP wide module features twelve fixed frequency, inductor based bandpass filters, set at half octave interval spacing and covering from 125 Hz through to 5.8kHz. It also features low pass and high pass shelf filters, again they are fixed frequency and both are active inductor based circuits. It has a vintage pedigree that harks back to the original and highly sought after 914 Fixed Filter bank from the 1960's Moog 900 series modular synthesiser system, however we have brought this design up to date and made it compact enough to fit into skiff friendly Eurorack cases by using gyrator based active inductors, and have added some other very useful features too - the bands are split alternatively to left and right channels, each having their own individual output, and there is also an inbuilt Voltage Controlled cross-fader that allows panning between the left and right banks, with a mix of all bands available in the central position.

In addition, we have a second cross fader that can mix between the dry incoming signal, or an external signal fed into input 2, and this is cross-faded against the wet MIX Output - this allows Voltage Controlled crossfading from wet to dry signals, or between wet and external signals - and the level of each can be adjusted using the Input 1 and Input 2 level controls.

A further addition is the feedback control, this is similar in design to the resonance control on a regular VCF, but because of the multiple fixed filters topology it is rather different in operation - it would normally be added in small amounts to thicken up the sound, however we have allowed the feedback to traverse to quite extreme settings for howling feedback and even soft clipped self-oscillation, especially for the noise merchants out there...

Using L/C inductor topology bandpass circuits rather than the usual Sallen Key R/C active bandpass filters does give a slightly different sound and this is part of the magic of the original 914 filterbank, as the LC based circuit exhibits less phase shift against frequency that the more common Sallen Key R/C based bandpass filters that are used in many Modular synths.

Many people often wrongly assume that a fixed filter bank is exactly the same as a graphic equaliser - however this is certainly not the case, if all of the controls of a graphic EQ are set to centre then a flat frequency response is expected and the output will sound very similar, or identical to the input - this does not happen with a fixed filter bank, the frequency response rises and falls as it passes between each stage (but to a lesser extent than if the filters are all set to maximum output), so it acts as a soft slope comb filter, and the resulting output sounds very different from the input signal. Also, with all of the individual filters turned to zero there will be no output at all.

Notes: The original MiniMod Glide +Noise module was based exactly on the original Minimoog Model D circuitry, which was designed to be used with the built in Model D keyboard, and because of its vintage design its range was severely limited to 5 or 6 octaves, and it also responded to positive voltages only. Another limitation was that it would not return fully to zero when selecting long glide times, which restricted the range even more.

So we made the decision to re-design the MiniMod Glide + Noise using modern precision parts, and we have come up with an all new circuit which has exactly the same function, but with a hugely extended range. It has the same Glide slope characteristic (a slightly curved Linear Glide) as the Model D on which the MiniMod is based, however in response to many requests from customers we have adjusted the glide up and down speeds so that they are now very similar , which is much more useful in real world applications that the earlier MK1 version which (like the Model D) would glide up considerably faster than it would glide down.

The new Mk2 MiniMod Glide Noise module now has an impressive 14 octave range, and can respond to negative voltages down to -5V. This is a very useful feature, as our MiniMod VCO's will respond to negative control voltages and produce correspondingly low frequencies; so it is now possible to glide down quickly or slowly to crazy sub bass levels! The hold feature has been improved too, it covers the full audio range as well as DC control voltages, and works as a track and hold module with Eurorack signal levels.

A further enhancement is that the Mk2 module can now (using selectable jumpers) transmit or receive pitch CV to the Eurorack power bus; for example, the Glide CV Output can now be directed to the Bus in order to send CV's to (for example) three VCO's via the bus without the need for a passive multi and four patch cords!

The Noise section of the module is unchanged, except that we have slightly boosted the level of the Red Noise output to bring it more in line with Eurorack control voltage levels.

Lastly, it is much shallower - Mk1 Glide Noise had a depth of 54mm, and it was the only MiniMod module that was too deep to fit a skiff style case - and this prevented a full MiniMod system being installed into a shallow Eurorack case. The new MK2 version is only 28mm deep, so this allows both it and a full MiniMod system to be mounted into shallow skiff style Eurorack cases.

Dimensions: 6HP wide, 26mm Deep
Current draw: 36mA Positive, 38mA Negative

Notes: Engineered in the UK specifically for the Native Instruments Maschine Mikro MK3 Controller, a tough but lightweight polycarbonate shell protects from dust, liquid and accidental impact. Precision moulded for an exact fit whilst accommodating cables, your Native Instruments Maschine Mikro can sit ready for operation. Slides straight into a flight case or bag ready for transportation. Shields delicate controls and internal components from damage at home, on the road and on stage.

Notes: Decksaver LE (Light Edition): Still made from super durable polycarbonate, but reaching you at a more affordable price.

Engineered in the UK specifically for the Teenage Engineering OP-Z synthesizer.

Custom moulded to fit the contours of the unit whilst leaving USB connections in place, the OP-Z can sit ready for operation.

Super durable polycarbonate shell protects delicate keys during transportation and slides straight into a flight case or bag for maximum protection.

Dimensions

Weight 0.12 kg
Length 22.6 cm
Width 6.4 cm
Height 3 cm

Notes: The tools we use to compose and produce music are dear to our hearts. Dust, liquid and accidental impact have taken many a good synth down over the years - this is where Decksaver steps in. Precision trimmed for perfect fit whilst accommodating cables, the TipTop Audio Mantis Case can sit ready for operation. This cover is designed with 55mm clearance for patch cables, meaning you can leave your cables in place when travelling or protecting your modular setup in the studio. Shields delicate controls and internal components from damage at home, on the road and on stage.

Notes: This snake is designed connect gear with unbalanced phone jacks to gear with phono jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed connect gear with unbalanced phone jacks to gear with phono jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed to interconnect pro audio gear with unbalanced phone jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed to interconnect pro audio gear with balanced phone jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: 1/4 in TRS to Dual 1/4 in TS

This snake is designed to connect channel inserts on a mixing console to effects processors with unbalanced phone jacks. It is ideal for use in touring and other live-sound applications.

Features include:
Serviceable, all-metal plugs for rugged durability and ease of repair
Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: Serviceable 1/4 in TRS to Dual 1/4 in TS
Conductors: 24 AWG x 2 OFC

Notes: Metron is a 16-channel trigger and gate sequencer for Eurorack with extensive functions, expansion possibilities and the tools you need to create long sequences with many variations in a very short time.

The sequencer allows pattern lengths of up to 256 steps, and the number of steps per channel can be varied to create interesting and varied rhythmic structures. These patterns can be quickly stored and exchanged between units via the SD card slot. Metron also offers a random function per step and a ratcheting function.

With the optional WMD Voltera, Metron can be expanded with four additional bipolar voltage outputs.

Features:

16 Channels of trigger and gate signals
intuitive drum sequencer
View 4 channels at a time and easily switch views
Single track view lets you zoom in on a single track and see 64 steps at a time
Up to 256 step pattern length
Different pattern lengths per channel
Five instantly recallable, editable variations
View and edit variations that are not playing for easy cue and non stop performance play
Save patterns to SD memory for easy recall on power cycle
No-stop loading from memory
Easy view memory previews lets you see a pattern before loading from memory.
SD allows for easy update as well as easy back up / file transfer from unit to unit
FX / Fills for instant / momentary variation
2 assignable inputs for external CV control
Tap in patterns with quantized recording with the buttons or external source
Quick copy / paste / clear functions
Internal clock with Swing
dedicated reset output
MIDI Preset mode lets you send MIDI messages to other modules on the Doepfer CV bus. (for use with WMD SSM, Malekko Voltage Block, and more)
Random Pattern Generation
Probability per step and group probability functions
Burst per step for ratchet / roll sounds
Custom Fill Patterns for instant fills
Trigger Mutes
Step looping
Manual gates
Power consumption: 180mA at +12V and 0mA at -12V

Depth: 31mm

HP : 36

Notes: Play is a high-fidelity sample player with a full feature set.

Up to 32 samples can be loaded at a time and dynamically switched between using the file knob and associated CV input. Playback modes include one-shot, looping, or gated playback; all with extremely low latency. Transform your samples by pitching them up two octaves or down three octaves, all with a pitch knob that can be free running or quantized to semitones. The pitch CV input tracks volt per octave across its entire range and allows for musical sequencing of samples. Play ships with a pre-loaded SD card packed with loops, drum hits, and field recordings to get you up and running immediately.

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod60 Unpowered is 60HP with 1.34" (34mm) of available module depth. No power supply is included, you must supply your means of powering modules with a DIY power supply or a front-facing module such as the Row Power. Two holes on the rear face are plugged with removable plastic plugs, and can be used for DIY applications.

Notes: Module A-183-9 is a simple power supply for up to four devices which can be powered via USB (e.g. keyboards, smartphones). An LED shows is the +5V are present.

The module has no USB function but provides only the +5V supply for USB devices.

A control LED shows if the +5V are present.

Note: The module requires an A-100 case with built in power supply A-100PSU3. Only this A-100 supply has the required +5V available. We do not recommend the usage of an older A-100 case with A-100PSU2 as this would require the +5V adapter A-100AD5 and the max. current would be limited to 100mA.

Notes: The PRO-SOLO Mk3 converts MIDI data into CV- gate and clock signals. The operation is easy and clear, settings can be saved in non-volatile memory. High-resolution 16-Bit converters provide accurate tracking and fast response. 1V/oct and Hz/V characteristics are possible as well as normal gate and Switched Trigger (S-Trig).

The unit features two CV- and one gate output, additionally there's an analogue clock output. MIDI thru socket can also be used as DIN-Sync output or it can output two additional voltages with a special cable. MIDI synched LFO.

Notes: 16-conductor ribbon cable with four 16-pin connectors (20" total length), for connecting more than 2 modules in a Pod.

Notes: Power brick for powering Pods. One power brick can power up to 10 typical Pods. Pods can be daisy-chained using a Barrel Cable or Long Barrel Cable.

15-20V / 90W / 2.1mm Barrel Plug (5.5mm outer diameter) / Positive Centre.

Compatible power bricks are available wherever ROW POWER modules are sold. You also may use your own power brick if it meets the following requirements:

- 15V to 20V DC
- Positive centre 2.1mm barrel plug
- Minimum 30W output power
- Low-noise output
- Compatible with an IEC C5 cable

Please note: IEC cable not supplied

Notes: Kickall is a 6HP compact synth voice that features everything needed to make a big fat Kick sound. A stable VCO that tracks V/Oct, a couple of VCAs, envelopes for volume and pitch and an aggressive waveshaper.

The module has been designed with a kick synthesis patch in mind.

The audio path consists of a sinewave oscillator that passes across a Square Waveshaper and two VCA's. The first VCA is for the Volume envelope. The second VCA is dedicated to general volume. Thanks to his CV input, it is possible o apply accents or affects the dynamics of notes. Feeding this input with audio generates a basic AM operation expanding the sonic range of the module.

In the control path, KickAll has two envelope circuits to modulate the first VCA oscillator's pitch. Both envelopes are fired at the same time manually or via dedicated trigger input.

Through its Tune input, KickAll tracks eight octaves with high accuracy. Plug your favourite sequencer or CV source to create patterns out of the kick range, or feed it with an audio signal, for frequency modulation Fx.

Specs

Current needs: +12V: 26mA, -12V: 12mA
Width: 6 HP
Depth: 20mm, (28mm DIY) including power connector
Aluminium, heat-treated front panel.
Designed, kits prepared and completed modules assembled in Barcelona.

Notes: Additive synthesis oscillator based on the concept of building up harmonics from sine waves. A complex idea nicely executed for ease of use.

Suppliers notes:
Odessa implements the principle of additive synthesis controlled by a set of carefully tailored macro parameters to harness thousands of sinusoidal partials that altogether form the resulting sound.

The interface is kept simple and accessible, so you can easily build rich and full, great sounding timbres of very complex spectra, that can be either harmonic or inharmonic. Even though inharmonic spectra yield non-periodic waveforms, all partials are frequency related to the common fundamental controlled by a V/oct input. The series of harmonics can be squeezed or spread apart, tilt, and pruned by a comb-like frequency response, resulting in a variety of unearthy sounds. Animating the comb response yields radical effects similar to flanging and phasing. Additional, often sought after features are implemented: through-zero linear frequency modulation, and unison detune: up to 5 copies of the sound can be spread apart for a fat and dense cluster of voices.

There are nine parameters, each controlled by a dedicated knob, so the workflow is as smooth and immediate as possible. Furthermore, every parameter has a dedicated CV input, allowing live animation for organic audio effects. Odessa sports two main outputs for banks of harmonic partials that can be further scaled in frequency, as well as an additional output that can either spit out a square wave or a single sinusoid of the fundamental frequency. Interesting spatial effects, crazy modulation feedbacks as well as synchronisation is possible that way.

The hardware is based on a powerful FPGA chip offering massive parallel computing. The synthesized signal is devoid of aliasing through the entire audio range thanks to intrinsically bandlimited algorithm. A simplified spectral analyser helps you to keep a visual track of what is actually happening to the harmonics.

For even more control over Odessa, you can use the Leibniz subsystem (or just the Lipsk) that can be connected to a header at the back of the module.

Notes: IsoAcoustics introduce the next evolution of their specialized line of speaker stands for the audio professional, music hobbyist, audiophile, and music lover. The new ISO Series of speaker stands provide superior acoustic isolation and enhance the sound clarity of any speakers including studio monitors, home theatre systems and sound reinforcement.

With a lower profile and new contemporary design, the ISO Series of stands positions your studio closer to the supporting surface or meter bridge, and the new redesigned isolators moves the acoustic performance another step forward.

IsoAcoustics ISO Series speaker stands are built with a unique, patented isolation technology that provides a high degree of isolations and manages the speaker's energy to deliver authentic, uncoloured sound. This next generation of speaker stands effectively eliminates energy transfer into the supporting surfaces. Bass becomes tighter, overall imaging is enhanced and your speakers are enabled to perform to their full potential. Following the same design philosophy as the ISO-L8R Series, these isolation stands provide 14 variations of height and tilt adjustment to optimize the placement and performance of studio monitors by getting the tweeters in the correct alignment with the listening position.

Whether you're a pro mixing in the studio - a musician creating in a home project environment - or an audiophile who appreciates every nuance of music and sound - you'll hear and appreciate the difference with the ISO Series speaker stands. It's simply the best investment you can make for superior audio.

ISO-130:

Designed for smaller speakers and studio monitors. These stands provide 14 variations of height and tilt to optimize speaker placement and performance. Isolate your studio monitors from the supporting surface and allow them to breathe so they can deliver the clearest and most accurate sound possible.

5.1"x6"/13x15cm Short: 2.7"/8cm Tall: 8"/20.3cm 20 lbs/9kg

Notes: The Multi-Delay Processor is a creatively usable echo effect with eight taps. The module's sound may remind you of classic bucket-brigade devices. - It even generates distinctive pitch effects when altering the delay time. An input mixer gives audio material a crisp, analogue character. Thanks to feedback channels with pitch shifter and reverb processor, shimmering echoes and other atmospheric effects can be achieved. A total of nine envelope followers and 14 audio outputs invite you to do extensive feedback patches and other edgy experiments.

The Multi-Delay Processor isn't just a high-quality echo effect but was designed to be a fundamental ingredient of patches. Its core is a bank of eight digital delays, which are wired in series. Together, the circuits form a multi-tap echo. The volume of each signal repetition as well as the raw material can be adjusted via faders. Furthermore, there are individual audio and envelope follower CV outputs for the dry signal and all taps. An analogue clock is used to control the echo circuits. The delay time can be set manually via a potentiometer plus there are two CV inputs with bipolar attenuators. Altering the delay time parameter during operation leads to pitch effects. At this point at latest, you'll realize the superiority of the serial memory design used by Mark Verbos over average effect chips. Despite its digital core, the Multi-Delay Processor offers charming sound reminiscent of a classic bucket-brigade device. - Only cleaner and more transparent.

A three-channel mixer with dedicated level potentiometers adds analogue character to signals before they are fed to the delay circuits. Without patch cables plucked into the second and / or third input, you can use these channels as feedback paths with additional effects. In detail, a pitch shifter calibrated to +1 octave (channel 2) and a reverb (channel 3) are available. - A perfect setup for creating shimmering echoes and other atmospheric effects. High feedback values make the module self-oscillate. In contrast to the multi-tap delay, which consists of individual components, an FV-1 chip is used for pitch shifting and reverberation. This processor is well-known, as it is the main component of multi-effects modules like the Erica Black Hole DSP and numerous guitar pedals. Here, the FV-1 is "just" a creative addition to the main effect.

In addition to the manual mix output, which emits the mixture of raw and effect material dialled in via the faders, there are four other audio outs. Two of these connectors provide signals derived from summing up all even respectively odd taps. The other sockets emit preset mixes with increasing or decreasing level. - Very cool for quickly creating special effects.

Notes: The Falistri is a fully analogue multi-purpose movement manager designed to generate and edit voltages to easily accomplish any patch.

The module can be divided into two big parts: in the upper two-thirds of the panel take place two specular function generators, while the lower third is composed of a dual cascaded frequency divider, a linear slew limiter, and a four-quadrant multiplier.

Key features:

Two Function Generators: Envelopes, LFOs, Oscillators
Adjust the Shape Without Changing the Time
Exclusive Shapes per Stage
Trig Buttons: Play Those Envelopes!
Three Play Modes (Voltage-Selectable)
Interacting Functions: Quadrature Mode
All the Outputs, Everywhere
Cascaded Frequency Dividers
Four-Quadrant Multiplier
Linear Slew Limiter

Size 18 HP
Depth 38 mm

Current draw
170 mA @ +12 V
170 mA @ -12 V

Notes: Erica Synths Acidbox III brings you the core of the famous Polivoks VCF in stereo version with a unique audio signal overdrive circuit, built in LFO and envelope follower in a compact, full aluminium case.

The Acidbox III has adjustable input gain, therefore it works with various sound sources - guitars, units with line level signals (synthesizers, grooveboxes, etc.) and modular synths. Configurable control input allows you to connect a bypass footswitch, expression pedal, external cut-off control voltage source and LFO synchronization trigger. This makes the Acidbox an ideal companion in almost every production or live performance setup.

Notes: Erica Synths MIDI to Trigger module lets you control your drum modules and trigger events on your modular from any MIDI sequencer!

If you want to use a MIDI sequencer to trigger events on your modular synthesizer (e.g. using the hexinverter.net Mutant drums range or Tiptop Audio classical drum modules or envelope generators to control VCAs), Erica Synths MIDI to Trigger module is just what you need, it converts ANY MIDI notes to eight 10ms Trigger signals.

When designing the module, Erica Synths put usability as priority; it will take you seconds to program the module. It works with any MIDI sequencer & controller so there is no need to change MIDI controller settings, instead, you reprogram the module.

Notes: IThe Drum Sequencer is easy to use, classical X0X style live performance oriented sequencer module that provides the ultimate control over your system. Erica Synths Drum Sequencer might be the last modular sequencer for drums and basslines you will ever have to buy!

Features:
16x trigger outputs
12x accent outs
1x CV track with scales
1x Gate track
2x LFO with independent or synced to the BPM frequency
LFO attenuation per out
Max pattern length = 64 steps
Time signature per Track
Direction per track/pattern
Pattern length per Track
Shuffle per track
Probability per step
Retrigger per step
Time shift per step
Instant pattern switching
Solo/Mute tracks
Step/Tap record modes
8 Banks of 16 Patterns
Quick Copy/Paste per tracks & patterns
Pattern linking
Song mode
MIDI sync in with Start/Stop
External 4PPQ clock in
Firmware upgrade via MIDI SysEx??
Specifications and appearance are subject to change without notice for improvement.

Technical specifications:
Trigger amplitude: 5V
Panel Width: 42 HP
Module depth: 30mm
Power consumption: 152mA@+12V, 56mA@-12V