100% Compra Segura

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Compra Segura

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Bestsellers: All Genres

View:
Options
Artículos del 1 al 50 de 122 en la página 1 de 3
1  2  3  »
1
Doepfer A-124 Wasp Filter SE Module (special edition black & yellow version)
Cat: 671564 Rel: 29 Nov 17
 
12dB multi-mode filter with unique classic circuitry, based on the filter from the 70s EDP Wasp synth
Notes: Module A-124 is a special 12dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies, manufactured by the UK company "Electronic Dream Plant" with Chris Huggett und Adrian Wagner). This design "abuses" digital inverters as analog operational amplifiers leading to distortions and other "dirty" effects that generate the specific sound of this filter. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

Inputs: Audio In, CV In (2x)
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio and CV attenuator, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the module SEM VCF A-106-5. But the sound of both filters is very different! The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer).

- 3U Eurorack module, 8HP wide, 45mm deep
- Current draw 30mA
Read more
 9 in stock $81.71
Click for better price!
quote 671564
2
Doepfer A-138m 4x4 Matrix Mixer Module
Cat: 716959 Rel: 29 Jan 19
 
Matrix mixer with 4 rows & 4 columns - 20HP
Notes: Module A-138m is a 4 x 4 matrix mixer with switches for unipolar/bipolar mode for each column. Unipolar means that the controls work as attenuators. Bipolar means that the controls work as polarizers. In this mode the amplification is zero in the middle position of the corresponding control. Turning the knob counter-clockwise from the centre position the signal is subtracted from the output sum with increasing amount (i.e. negative). Turning the knob clockwise from the centre position the signal is added to the output sum with increasing amount. The module is DC-coupled and can be used for both audio and control voltage mixing.
Read more
 3 in stock $121.52
3
Doepfer A-138s Mini Stereo Mixer Module
Cat: 671589 Rel: 29 Nov 17
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 5 in stock $72.28
Click for better price!
quote 671589
4
Doepfer A-145-4 Quad LFO Low Frequency Oscillator Module
Cat: 731949 Rel: 10 Jun 19
 
Quad low frequency oscillator - 4HP
Notes: Module A-145-4 is a simple quad LFO (Low Frequency Oscillator). Not a very "exciting" module, just a bread-and-butter device and a simple demon for work. Virtually in every modular system several LFOs are required for modulation purposes. The module contains four simple LFOs with the waveforms triangle and rectangle. A dual colour LED (red = positive / yellow = negative output voltage) indicates the triangle output of each LFO. The frequency range can be chosen for each LFO individually by means of a jumper between about 50 Hz ... 0.04 Hz (about 20 seconds, jumper removed) and about 2Hz ... 0.002 (about 8 minutes, jumper installed).

The module can be treated as a slimmed version of the quad LFO A-143-3 as it has similar features available. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is less than one third of the A-143-3. The module is primarily planned for applications where only limited space is available. The functional difference compared to the A-143-3 are the missing sawtooth outputs and frequency range switches.
Read more
 1 in stock $75.42
Click for better price!
quote 731949
5
Doepfer A-140-2 Dual Micro ADSR Module
Cat: 684450 Rel: 18 Jul 18
 
Dual ADSR envelope generator - 8HP
Notes: Module A-140-2 contains two ADSR type envelope generators behind a front panel with 8 HP only.

Each ADSR provides these controls and in/outputs:

- LED (displays the envelope output)
- A: manual Attack control
- D: manual Decay control
- S: manual Sustain control
- R: manual Release control
- Gate Input
- Retrigger Input
- CVT Input with attenuator (CVT = CV Time)
- Envelope Output 1
- Envelope Output 2

The output voltage range for each envelope is 0 - 10V. The time range of Attack/Decay/Release is about 1ms to 30s.

By means of internal jumpers one can select which time parameters are controlled by the CVT input (e.g. D only or D+R or A+D+R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question).

Socket CVT can be normalled to an internal fixed voltage (i.e. the switching contact is connected to an internal fixed voltage). That way it's possible to change all time parameters simultaneously by means of the CVT control.

Another jumper is used to set output 2 to normal or inverted envelope.

And another jumper is used for the normalling of Gate 2 to Gate 1 (i.e. ADSR#2 is also triggered by Gate 1).

Two more jumpers are used for the optional bus access to the gate signal of the bus for each ADSR. Changing the positions of the mentioned jumpers allows to modify the factory settings.
Read more
 2 in stock $125.71
Click for better price!
quote 684450
6
Doepfer A-135-2 Quad VCA & VC Mixer Module
Cat: 714704 Rel: 22 Jan 19
 
Compact voltage-controlled four-channel audio mixer - 8HP
Notes: A-135-2 is a miniature version of the A-135-1. Behind a front panel with 8 HP only four linear VCAs (voltage controlled amplifiers) and a voltage controlled mixer based on the VCAs are available.

Controls, In/Outputs and Functions of each VCA:

- Level (manual control of the VCA amplification), small rubberized knob (L1...L4)
- Control voltage input with associated attenuator (CV1...CV4), for the full VCA control range about 0...+5V control voltage are required (attenuator fully clockwise), for higher control voltages the attenuator is used, the attenuators are without knobs, just plastic shafts with white marker
- Signal Input
- Signal Output
- All inputs and outputs are DC coupled. Consequently the VCAs can be used to process both audio and control voltages (e.g. to control the level of LFOs or envelopes)
- The signal input is not equipped with an attenuator. But the VCAs can process all signals up to 15Vpp / -7.5...+7.5V without clipping. In case of higher levels an external attenuator is required (e.g. A-183-1).
- The available amplification range is 0...1, the maximal amplification is 1 (i.e. it "clips" and remains at 1 even if the control voltage goes beyond the value that corresponds to amplification 1)

Functions of the voltage controlled mixers:

- Two outputs ("Selected" and "All")
- Selected output: the ouput if a VCA is removed from this sum signal when a plug is inserted into the corresponding VCA output.
- All output: sum of all VCA outputs, regardless of inserted plugs into the VCA outputs
- The maximal amplification is about 0.6 to avoid clipping at the mixer outputs (otherwise the outputs may distort with 15Vpp signals at each signal input and full amplifications)

Special functions of the voltage controlled mixers (selectable by internal jumpers):

- Dual Stereo VCA: In this case the control unit of VCA1 (L1 + CV1) affects also VCA3 and the control unit of VCA2 (L2 + CV2) affects also VCA4, the control units of VCA2 and VCA4 are out of operation
- Quad VCA: In this case the control unit of VCA1 (L1 + CV1) affects all four VCAs. The control units of VCA2, VCA3 and VCA4 are out of operation. In this mode the module has the same function as module A-132-2. That's why module A-132-2 will be discontinued.
- Normalling of the signal inputs: by means of internal jumpers signal input 1 can be normalled to signal input 2, signal input 2 to signal input 3 and signal input 3 to signal input In 4. That way the same input signal can be distributed to four different channels by means of control voltages (e.g. quadrophonic distribution of audio signals). Suitable control voltage sources are e.g. A-144 (Morphing Controller) or A-143-9 (Quadrature LFO).
Read more
 5 in stock $111.04
Click for better price!
quote 714704
7
Doepfer A-151v Quad Sequential Switch Module (vintage edition)
Cat: 684462 Rel: 22 May 18
 
Electronic switch with up to four steps - 4HP
Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in/outputs, and a common out/input. Each time a pulse is received at the trigger input socket, the common out/input is connected to the next in/output. After the fourth in/output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out/input immediately back to the first in/output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LED's indicate the active in/output (ie. the one that is connected to the out/input at any particular time).
Read more
 4 in stock $58.66
Click for better price!
quote 684462
8
Doepfer A-160-2 Clock Trigger Divider II Module
Cat: 671576 Rel: 29 Nov 17
 
Enhanced clock divider with multiple dividing factors - 4HP
Notes: Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg. LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

These are the most important features of the module:

Three different sets of dividing factors, selected by a three-position switch at the front panel:
- Power of two: 2, 4, 8, 16, 32, 64, 128
- Prime numbers: 2, 3, 5, 7, 11, 13, 17
- Integer: 2, 3, 4, 5, 6, 7, 8

Two output modes, selected by a two-position switch at the front panel:
- Gate mode: outputs act like the outputs of typical binary dividers
- Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
- Clock edge type selected by a jumper on the pc board:
- Positive: the rising edge of the clock signal triggers the state change of the outputs
- Negative: the falling edge of the clock signal triggers the state change of the outputs

Reset behaviour by two jumpers on the pc board:
- Level triggered: the level at the Reset input triggers the Reset
- Edge triggered: the edge of the signal at the Reset input triggers the Reset
- Positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
- Negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset

Output polarity selected by a jumper on the pc board:
- Positive: non-inverted outputs
- Negative: all seven outputs are inverted

Width: 4HP / 20mm
Depth: 35mm (Measured from the rear side of the front panel)
Current: +12V: +50mA, -12V: -0mA
Read more
 5 in stock $92.18
Click for better price!
quote 671576
9
Doepfer A-138n Narrow Mixer Module
Cat: 731947 Rel: 10 Jun 19
 
Compact 4-channel mixer - 4HP
Notes: Module A-138n is a simple four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator available. The output is twice available (two sockets, hard-wired like a multiple).

The module is the slim version of module A-138a and offers nearly the same features. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-138a. The module is primarily planned for applications where only limited space is available. The only functional difference compared to the A-138a is the missing attenuator for the (dual) output.
Read more
 4 in stock $46.88
Click for better price!
quote 731947
10
Doepfer A-180-9 Multicore Module
Cat: 671561 Rel: 18 Dec 17
 
Pair of multicore signal connectors
Notes: A-180-9 is another simple but useful tool. It can be used to connect up to 14 signals between different cases by means of standard network cables (RJ45). These cables are available all over world smoothly in different lengths and colours. From the factory two black network cables with 0.5 m length are enclosed.

The upper network connector is wired to the eight sockets 1-8, the lower to the six sockets A-F. That way it's possible to pre-patch different cases and connect signals, that are required in all cases (e.g. clock, start/stop, master CV) by means of one or two cables only instead of 14 individual patch cables. When only eight signals are required only the upper network connector is required and the sockets 1-8 are used. When more than eight signals have to be patched both network connectors have to be used. It's also possible to wire the upper and lower network to different cases (i.e. signals 1-8 to external case #1 and signals A-F to external case#2).

The module is fully passive (no power supply required) and simply wires the 14 sockets to 14 pins of the network connectors.

The A-180-9 comes in pairs for combining two modular systems.
Read more
 9 in stock $104.76
Click for better price!
quote 671561
11
Doepfer A-118-2 Noise, Random, T&H, S&H Module
Cat: 731938 Rel: 10 Jun 19
 
Noise/random generator - 4HP
Notes: Module A-118-2 is the slim version of module A-118-1 and offers essentially the same features as the A-118-1. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-118-1. The module is primarily planned for applications where only limited space is available. The functional difference between A-118-1 and A-118-2 is the additional T&H/S&H unit which is not included in the A-118-1.

The module generates the signals white noise, coloured noise, continuous random voltage and stepped random voltage (derived from the continuous random voltage by means of a S&H/T&H unit).

The noise signal is generated 100% analogue by amplification of the noise of a transistor. White and coloured noise are usually used as audio sources. The random voltages are normally used as control voltages (e.g. for filter frequency or any other voltage controlled parameter).

The A-118-2 gives you the ability to mix the relative amounts of Red (low frequency component) and Blue noise (high frequency component) in the coloured noise output.

For the continuous random voltage the rate of change (Rate) and amplitude (Level) of the random voltage can be adjusted. The continuous random voltage is derived from the coloured noise signal by low pass filtering. Consequently the settings of the controls for the coloured noise (Blue, Red) affect the behaviour of the random voltage! A dual colour LED (red = positive / yellow = negative output voltage) indicates the continuous random voltage.

The continuous random voltage is used as source for the S&H/T&H unit. The type of operation can be set to S&H (sample and hold) or T&H (track and hold). When T&H is chosen the output signal follows the input signal (= continuous random voltage) as long as the Clock input is "high". As soon as the clock signal changes to "low" the last voltage is stored. When S&H is chosen the input signal (= continuous random voltage) is sampled at the rising edge of the Clock signal.

For the Clock signal a "digital" signal (e.g. Clock, Gate, rectangle output of an LFO) is required. It does not work with slowly changing continuous CV signals. Another dual colour LED (red = positive / yellow = negative output voltage) indicates the stepped random voltage.
Read more
 3 in stock $75.42
Click for better price!
quote 731938
12
Doepfer A151 Quad Sequential Switch Module
Cat: 577792 Rel: 06 Jun 19
 
Electronic switch with up to four steps - 4HP
Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in / outputs, and a common out / input. Each time a pulse is received at the trigger input socket, the common out / input is connected to the next in / output. After the fourth in / output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out / input immediately back to the first in / output (see Fig. 1). Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LEDs indicate the active in / output (i.e. the on that is connected to the out / input at any particular time).
Read more
 5 in stock $58.66
Click for better price!
quote 577792
13
Doepfer A-138sv Mini Stereo Mixer Module (vintage edition)
Cat: 684443 Rel: 30 Apr 18
 
Four-channel stereo mixer - 8HP
Notes: A-138s is a simple but useful 4-in-2 mixing tool. It has four inputs available. Each input is equipped with an attenuator (Level) and a panning control that is used to distribute the signal to the left and right output. Beyond stereo mixing it is equally suited to create variable parallel routings. For example: Any of the four inputs may be routed in variable intensity to feed two filters.

You may regard the A-138s as a smaller version of the A-138m Matrix Mixer.

Inputs and outputs are DC coupled, i.e. the module can be used for the mixing of control signals too.

- 3U Eurorack module, 8 HP wide, 30 mm in depth
- Power consumption: 10 mA at +12 V and 10 mA at -12 V
Read more
 5 in stock $81.71
Click for better price!
quote 684443
14
Doepfer A-106-5 12dB SEM Filter Module
Cat: 577753 Rel: 06 Jun 19
 
12dB multi-mode filter - 8HP
Notes: Module A-106-5 is a 12dB multimode filter that is based on the filter circuit of the Oberheim SEM module.

The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates.

The module does not feature self-oscillation in contrast to most of the other filters of the A-100 system.

The module generates a distorted audio signal if the level control is set to about 50% (i.e. centre position) or more with A-100 standard signals like VCOs.
Read more
 5 in stock $77.52
Click for better price!
quote 577753
15
Doepfer A-148 Dual Sample & Hold Track & Hold Module
Cat: 577745 Rel: 29 Nov 17
 
Two sample & hold units in one module for generating stepped random voltages or slicing signals
Notes: Module A-148 (Dual S&H) has two identical sample & hold modules, designed to produce 'staircase' voltages. The signal present at the sample input is sampled at a rate set by the signal at the trigger input, and held at that voltage at the S&H output.

The exact shape of the staircase depends on the sort of waveform at the sample input: NOISE or RANDOM signals produce random patterns; an LFO produces rising or falling staircase patterns.

Two LEDs for each S&H indicate the voltage (positive or negative) of the sampled signal.
Read more
 5 in stock $62.85
Click for better price!
quote 577745
16
Doepfer A119 External Input Envelope Follower Module
Cat: 577771 Rel: 29 Nov 17
 
Envelope follower & pre-amplifier for microphone/line-signals - 8HP
Notes: Module A-119 (External Input / Envelope Follower) is designed to allow external audio signals to be integrated into the System A-100. It comprises a pre-amp, envelope follower, and comparator.

The pre-amp has two inputs: an unbalanced input for line level signals, with a gain factor of from 0 to 20, and a balanced input with a gain factor of from 0 to 500, for insertion of low level signals, for instance from a microphone or electric guitar.

The Envelope Follower reads the signal level of the input, and puts out a proportional voltage as an envelope at its own output.

The comparator generates a gate signal whenever the input goes above an adjustable trigger threshold.

Three LED's help you keep track of overload, the envelope, and the gate signal.
Read more
 4 in stock $68.09
Click for better price!
quote 577771
17
Doepfer A199 Federhall Spring Reverb Module
Cat: 577748 Rel: 15 Aug 18
 
Reverb effects module with spring reverb tank - 8HP
Notes: Module A-199 is a spring reverb module. The reverb effect is electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical properties of the springs like signal delays, audio resonances, limited frequency range, acoustic feedback behaviour, sensitivity to mechanical shocks and others.

The 3-spring system used in the A-199 ensures a "dense" reverb because of the different properties of the three springs.

The A-199 implies some special features that are not self-evident for spring reverb units:

The reverb signal can be fed back to the input using the Feedback control. Even self-oscillation of the springs similar to the self-oscillation of filters is available. The feedback loop can lead even via external modules like VCA, VCF, phaser, frequency shifter, vocoder, distortion/waveshaper, ring modulator and others. In this case the reverb output of the A-199 is connected to the input of the external module(s) and the output of the external module(s) is fed back to the Ext. Feedback In socket of the A-199. This socket contains a switch that interrupts the internal feedback loop as soon as a plug is inserted.

Another feature is the Emphasis control. This enables the adjustment of the accentuation of middle frequencies (around ~ 2kHz).

With the Mix control the relation between original and reverb signal appearing at the mix output is adjusted.

Using all these features very extreme and unusual effects can be generated with the A-199.
Read more
 2 in stock $117.33
Click for better price!
quote 577748
18
Doepfer A138b Exponential Mixer Module
Cat: 577776 Rel: 29 Nov 17
 
Four channel mixer module - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain, i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138b has potentiometers with logarithmic response, so is especially suitable for audio signal mixing.
Read more
 3 in stock $55.52
Click for better price!
quote 577776
19
Doepfer Dark Time MIDI/USB Analog Sequencer (supplied with 2 pin Euro plug)
Cat: 427842 Rel: 14 Jun 11
 
MIDI/USB analog sequencer with red LEDs (240V only)
Notes: Dark Time is an 2x8 step analog sequencer with CV/Gate, USB and MIDI interface. It is intended as an add-on for the Dark Energy but may be used in combination with other MIDI, USB or CV/Gate equipment too.
Read more
 4 in stock $466.20
Click for better price!
quote 427842
20
Doepfer A100 LC1V Low Cost Eurorack Module Case With Integrated Power Supply & Bus Board (vintage edition, 100-240V)
Cat: 743113 Rel: 20 Aug 19
 
Compact budget Eurorack case
Notes: The A-100LC1v is a smaller version of the A-100LC3 with 48 HP of space. It is made out of raw wood, a black coating gives the Eurorack frame a vintage look. The built-in power supply, type A-100SSB, delivers up to 380 mA at +12 V and -12 V as well as 100 mA at +5 V.

The A-100LC1v comes equipped with one 48 HP measuring row for 3U modules. Its power supply features eight connectors for oscillators, filters and so forth. The case is connected to the grid via an IEC power socket.
Read more
 2 in stock $139.33
Click for better price!
quote 743113
21
Doepfer A-197-3 RGB LED Stripe Controller Module
Cat: 714708 Rel: 25 Mar 19
 
Controller module for static & dynamic control of RGB LED stripes - 4HP
Notes: Module A-197-3 is a control unit for RGB LED stripes. The LED stripe is glued e.g. to the inner edges of the cases A-100P6/P9/PMS6/PMS9/PMS12 to illuminate the modules and patching statically or dynamically. Especially during live events the dynamic illumination in sync with the sound is an eye-catcher. Each colour (red, green, blue) has available a manual control for the background brightness and a CV input with attenuator that enables the dynamic brightness controlled by other control voltages of the modular system. For example three envelopes can be used which also control the loudness or filtering of sound processing modules. But even other control applications are possible, e.g. LFO, random voltages, clock/gate/trigger signals, sequencer, Midi-to-CV.
Read more
 1 in stock $78.56
Click for better price!
quote 714708
22
Doepfer A-108 6/12/24/48dB Low Pass Filter Module
Cat: 692510 Rel: 19 Jun 18
 
Classic Moog voltage-controlled lowpass filter - 12HP
Notes: Module A-108 is a completely new voltage-controlled low pass filter based on the well-known transistor ladder (Moog ladder). The module has internally an 8-stage low pass filter with different slopes available: 6, 12, 18, 24, 30, 36, 42 and 48 dB per octave. In addition, it features a band pass output (i.e. band pass with transistor ladder). In the factory, the 4 low pass outputs of the A-108 are internally connected to the filter stages 6, 12, 24 and 48dB.

Resonance (Emphasis or Q) can be adjusted manually right up to self-oscillation, in which case the filter will behave like a sine wave oscillator. The A-108 features an external feedback input that enables the insertion of additional modules into the feedback path (e.g. VCA for voltage-controlled resonance or phaser/frequency shifter for phase/frequency shifting effects). The socket is normalized and internally connected to the 48dB low pass output if no cable is inserted into the feedback socket.

The frequency can be adjusted manually, or by voltage control. Three CV inputs (CV1, CV2, CV3) are available. CV2 and CV3 are equipped with attenuators.

The filter audio input is very sensitive so that distortion - if desired - is possible even with normal A-100 levels (e.g. VCO output). Self-oscillation will break off at high distortion levels as the internal feedback signal is drown out by the distorted audio signal. This feature may intentionally be used to create new sounds.

In combination with the Voltage Controlled Mixer A-135 and the Morphing Controller A-144 a filter with voltage-controlled slope can be realized (i.e. controlling the slope from 6dB to 48dB via CV).
Read more
 1 in stock $137.23
23
Doepfer A-100B2v Vintage Blank Panel 2TE (black)
Cat: 731209 Rel: 29 May 19
 
Robust, blank front panel for use with modular racks & other applications - 2HP wide
Notes: Blank panel, 2HP (10mm), constructed from anodised aluminium, black.
Read more
 1 in stock $5.76
24
Doepfer Dark Energy 3 Semi Modular Analogue Monophonic Desktop Synthesizer
Cat: 676098 Rel: 04 Apr 18
 
Fully analogue, monophonic stand-alone synthesiser with USB & MIDI interface
Notes: The Dark Energy III is a monophonic stand-alone synthesizer with USB and MIDI interface. The sound generation and all modulation sources are 100% analog, only the USB/MIDI interface contains digital components. It is built into a rugged black metal case with wooden side plates. High quality potentiometers with metal shafts are used and each potentiometer is fixed to the case (no wobbly shafts and knobs). The distance between the controls is wider compared to A-100 modules, and knobs with vintage look are used.

Doepfer say that the main differences between II and III are an improved VCO (no warm-up period, additional triangle waveform, wider frequency range), resettable LFOs, improved ADSR and a lot of internal access points for DIYers.
Read more
 1 in stock $416.96
25
Doepfer A-110-1 Standard VCO Module
Cat: 577769 Rel: 29 Nov 17
 
Standard VCO providing two CV inputs for pitch, an octave switch, four waveforms with separate outputs, pulse width modulation & hard sync - 10HP
Notes: Module A-110-1 is a voltage-controlled oscillator. This VCO's frequency range is about eight octaves (ca. 15Hz ... 8kHz). It can produce four waveforms simultaneously: rectangle, sawtooth, triangle, and sine wave (triangle and sine shapes are not perfect, see remark below). The output levels are typically 8Vpp for saw and rectangle, and 10Vpp for triangle and sine. The frequency or pitch of the VCO is determined by the position of the octave (Range) switch and tuning (Tune) knob, and by the voltage present at the CV inputs. Frequency modulation (FM) of the VCO is therefore a possibility. Footage (the octave of the fundamental) is set by the Range control in five steps, and Fine tuning controlled by the Tune knob by about +/-1 one semitone (can be modified for a wider range).

You can control the pulse width of the square wave either by hand, or by voltage control - Pulse Width Modulation or PWM.

For more detailed information please look at the user's manual A110_man.pdf. In addition, the A-110 service manual is available as an example for the A-100 service manual that is available at extra charges. This document describes also how to modify the sensitivity of the tune control, how to re-adjust the 1V/octave scale and the frequency offset (i.e. the absolute pitch). Such modifications should be carried out by experienced users only!

The core of the A-110-1 is a sawtooth oscillator (in contrast to the A-111-1, which is based on a triangle oscillator). The other waveforms are derived from the sawtooth by internal waveform converters. As the sawtooth reset (i.e. the back-to-zero slope) is not infinite fast but takes a little bit of time the derived waveforms triangle and sine are not perfect! At the top of the waveform they have a small glitch or notch that is caused by the sawtooth reset and cannot be eliminated by the waveform converters. The sine is derived from the triangle by a simple diode-based converter and the sine shape is not perfect (only a rounded triangle).

If a perfect triangle is required, the A-111-1 is recommended. For a perfect sine wave the quadrature LFO/VCO A-143-9 is recommended.
Read more
 2 in stock $143.52
Click for better price!
quote 577769
26
Doepfer A-106-5 12dB SEM Filter Module (special edition cream version)
Cat: 671592 Rel: 29 Nov 17
 
12dB multi-mode filter based on classic SEM filter circuitry
Notes: Module A-106-5 is a 12dB multimode filter that is based on the filter circuit of the Oberheim SEM module. The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal. If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates. The module does not feature self oscillation in contrast to most of the other filters of the A-100 system. The module generates a distorted audio signal if the level control is set to about 50% (i.e. centre position) or more with A-100 standard signals like VCOs.

Inputs: Audio In, CV1 In without attenuator, CV2 In with Polarizer
Outputs: Bandpass Out, Low/Highpass Mix-Out
Controls: Audio Attenuator, CV2 Polarizer, Frequency, Resonance, LP/HP Mix

The function and operation of this module is very similar to the Wasp filter module A-124. But the sound of both filters is very different! We will publish no separate user's manual for the A-106-5 but a combined manual for both A-106-5 and A-124. The only functional difference is the position of the sockets and controls, and the function of the controls CV2 (A-124: normal attenuator, A-106-5: polarizer)

Width: 8HP / 40.3mm
Depth: 55mm (Measured from the rear side of the front panel)
Current: +12V: +30mA, -12V: -20mA
Read more
 3 in stock $86.95
Click for better price!
quote 671592
27
Doepfer A138a Linear Mixer Module
Cat: 577762 Rel: 06 Jun 19
 
4 channel mixer - 8HP
Notes: Module A-138 is a four channel mixer, which can be used with either control voltages or audio signals. Each of the four inputs has an attenuator, and there's a master attenuator, so that the mixer can be used at the end of the audio chain - i.e. it can be used to interface directly with an external mixer, amplifier, etc.

The A-138a version features potentiometers with linear response, so especially suitable for control voltage mixing.
Read more
 2 in stock $55.52
Click for better price!
quote 577762
28
Doepfer A-121-3 12dB Multimode Filter Module
Cat: 731939 Rel: 11 Jun 19
 
Voltage controlled 12dB/octave filter - 8HP
Notes: Module A-121-3 is functionally nearly identical to module A-121-2. Only the distances between the controls and sockets are smaller and rubberized, small rotary knobs are used. Therefore the front panel width is only 4HP compared to 8HP of the A-121-2. In the first place it is planned for applications where only limited space is available. The only functional difference compared to the A-121-2 is the missing attenuator for the resonance CV input CQ.

These are the most important features of the module:

- Voltage-controlled multi-mode filter with a cut-off slope of -12 dB / octave (identical to the filter of the Dark Energy II/III but has been expanded by the voltage controlled resonance feature)
- Four simultaneous outputs are available, each with different characteristics: low-pass (LP), high-pass (HP), band-pass (BP) and notch (N)
- Manual control Frequ. for the cut-off frequency of the filter (the cut-off frequency determines the point at which the respective filter effect appears)
- Two inputs for frequency control by means of external control voltages (frequency modulation, e.g. by ADSR or LFO):
- Control voltage input CV1 without attenuator, about 1V/octave sensitivity
- Control voltage input CV2 with attenuator FCV2 for the adjustment of the modulation depth of input CV2
- Frequency range about 10Hz ... 20kHz
- Manual control Q for the resonance of the filter
- Control voltage input CQ without attenuator for voltage control of the resonance
- Resonance up to self-oscillation, in which case the module will behave like a sine wave oscillator even without audio input signal
- Audio input In with attenuator Level for the adjustment of the filter input level (beyond about pos. 5 clipping/distortion occurs with typical A-100 audio levels)
Read more
 1 in stock $93.23
Click for better price!
quote 731939
29
Doepfer A-130-2 Dual Linear & Exponential VCA Module
Cat: 731940 Rel: 11 Jun 19
 
Compact two-channel VCA - 4HP
Notes: Module A-130-2 is the slim version of module A-132-3 and offers essentially the same features. But the distances between the controls are smaller and rubberized small-sized knobs are used. In return the front panel has 4 HP only which is half the width of the A-132-3. The module is primarily planned for applications where only limited space is available.

The module is composed of two identical voltage controlled amplifiers (VCA). Each VCA has a manual gain control (also named Initial Gain) and a control voltage input with attenuator. The character of the control scale can be switched to linear or exponential. All inputs and outputs are DC coupled. Consequently the VCAs can be used to process both audio and control voltages (e.g. for voltage control of the level of LFO or envelope signals). The signal input has no attenuator available but is capable to process up to 16Vpp signals (i.e. -8V...+8V) without distortion. For the processing of higher levels an external attenuator (e.g. A-183-1) is recommended.

The amplification range is 0...1. Even with a higher external control voltage the amplification remains at 1 (kind of "amplification clipping" at 1).

Controls (for each of both units):

- Gain: manual gain control (Initial Gain) in the range 0...1
- CV: attenuator for the CV input
- Lin/Exp: switches the VCA characteristic to linear or exponential, in center position the VCA is off (mute function)

Inputs and outputs (for each of both units):

- CV: control voltage input, min. +5V required for max. amplification (1) with CV control fully CW and Gain fully CCW
- In: signal input, max. 16Vpp (+8V...-8V) without distortion
- Out: signal output
Read more
 2 in stock $75.42
Click for better price!
quote 731940
30
Doepfer A-182-2 Quad Switch Module
Cat: 731951 Rel: 11 Jun 19
 
Quad passive switch - 4HP
Notes: A-182-2 is a simple passive module that contains four changeover switches, which are used to connect or disconnect the sockets of the corresponding socket triplet:

- In the upper position of the switch the upper socket of the corresponding socket triplet is connected to the centre socket
- In the lower position of the switch the lower socket of the corresponding socket triplet is connected to the centre socket
- In the centre position of the switch the sockets are not connected

Each unit of the module can be used to switch between two signals or to interrupt/connect a signal. In the last case the third socket of the triplet is not used.

The module is fully passive and both audio or control signals can be switched.
Read more
 2 in stock $57.61
Click for better price!
quote 731951
31
Doepfer A-134-2 Dual Voltage Controlled Crossfader Module
Cat: 716922 Rel: 29 Jan 19
 
Dual crossfader module for voltage controlled morphing between two audio or CV signals
Notes: Module A-134-2 contains two identical voltage controlled crossfader units.

Each unit has two voltage controlled amplifiers (VCAs) with opposite control behaviour available. The outputs of the two VCAs are mixed together to obtain a common output. The behaviour of the control voltage inputs can be chosen with an internal jumper:

Symmetrical mode: If the corresponding jumper is not set both VCAs of the crossfader have the same 50% amplification with zero CV. If the applied CV becomes positive the amplification of VCA1 decreases and those of VCA2 increases in the same way. A negative CV has the opposite result. The CV voltage range to obtain the maximum/minimum positions of the crossfader is about -2.5....+2.5V. This mode is useful for bidirectional (i.e. positive and negative) control voltages, for example LFO or joy stick (adjusted to 0V CV in centre position).

Asymmetrical mode: If the corresponding jumper is set VCA2 is fully closed and VCA1 has full 100% amplification with zero CV. If the applied CV becomes positive the amplification of VCA1 decreases and those of VCA2 increases in the same way. The CV voltage range to obtain the maximum/minimum positions of the crossfader is about 0...+5V. A negative CV has no function in this mode. This mode is useful for unidirectional (i.e. only positive) control voltages, for example ADSR, ribbon controller or Theremin control voltage.

The CV input of the upper unit (CV1) is normalled to the CV input of the lower unit (CV2). I.e. if no plug is inserted to CV2 the CV input of the upper unit (CV1) also controls the lower unit.

The second signal input of the upper unit (In1B) is normalled to the first signal input of the lower unit (In2A). I.e. if no plug is inserted into In2A the signal In1B is used as the first signal input of the second unit.

As the inputs and outputs are DC coupled the module can be used for both audio and control voltage signal processing.
Read more
 2 in stock $69.14
Click for better price!
quote 716922
32
Doepfer A-132-1 Dual VCA Module
Cat: 710942 Rel: 29 Nov 18
 
Dual VCA with linear response - 4HP
Notes: Module A-132-1 (Dual Low Cost VCA) contains two voltage controlled amplifiers, with a linear response most suited to regulating the level of control voltages (ADSR amount, level of vibrato effect, etc).

In non-critical situations, though, its VCAs can be used to control audio signals.

Amplification is governed by the sum of the voltages patched into the two CV inputs.
Read more
 1 in stock $64.94
Click for better price!
quote 710942
33
Doepfer A-180-2 Multiples Module
Cat: 577779 Rel: 14 Jun 19
 
Passive multi-port distributor - 2HP
Notes: 2HP narrow version of the A-180 multiples module. It is a passive signal splitter suitable for audio or CVs. Two sets of four jacks are interconnected, by placing a solder bridge you can connect all eight jacks.
Read more
 2 in stock $35.16
34
Doepfer A-137-2 Voltage Controlled Wave Multiplier II Module
Cat: 716933 Rel: 29 Jan 19
 
Generates four phase shifted copies of a VCO signal applied to the audio input
Notes: Module A-137-2 is another version of a wave multiplier. In contrast to the A-137-1 Wave Multiplier I, the A-137-2 generates four phase-shifted copies of a VCO signal applied to the audio input. The four shifted signals are added to the original signal to obtain a fat sound similar to five independent VCOs. The phase shifting is made by a simple circuit that works only for sloped signals like sawtooth, triangle or sine, but not for rectangles or pulses.

The audio input signal (typically a sawtooth, triangle or sine wave from a VCO) is compared with a slowly varying control voltage (CV Shift In). The output of the comparator is a rectangle wave with variable pulse width. When the output of the comparatur is added to the input signal (a sawtooth in the example) with the correct level relation between both signals one obtains a phase shifted sawtooth. The left picture shows the incoming sawtooth wave on top. The two horizontal dashed lines (blue and orange) indicate two different comparison levels. Below the incoming sawtooth the two resulting comparator outputs (rectangle waves) and the two resulting shifted sawtooth waves are shown. It is not a "real" phase shift but an algebraic function. But the result is virtually the same. One could obtain the same function even with several comparator modules A-167 and mixers A-138a/b or polarizing mixers A-138c. But this would require a lot of modules.

The module has available four manual shift controls and four control voltage inputs with attenuators for the four internal shifting circuits. Typical sources for these inputs are LFOs, VCLFOs, random voltages, envelope generators, sequencers or other control voltage sources. Internally eight single outputs are available at single pins: the four shifted signals and in addition four rectangle outputs. A corresponding breakout module with eight sockets is in the planning stage and will be released provided that there are sufficient inquiries. The original signal and the four shifted signals are equipped with internal jumpers. If external toggle switches are used instead of the jumpers each of the 5 signals can be turned on/off individually.

The audio input is equipped with an attenuator to adjust the level for the right summation of the original and the comparator signals (as described above).
Read more
 2 in stock $76.47
Click for better price!
quote 716933
35
Doepfer A-134-1 Voltage Controlled Panner & Crossfader Module
Cat: 716920 Rel: 29 Jan 19
 
Voltage-controlled panning module consisting of 2 linear VCA's - 8HP
Notes: A-134-1 is a voltage controlled universal panning and/or crossfader module. If the module is used a voltage controlled Panning device one audio signal is panned to two different outputs. If the module is used a voltage controlled Crossfader two audio signals are mixed to one common output. The module enables even compositions of both functions.

The module contains two linear high quality VCAs (made with CEM3381/PA381 until April 2013, SSM2164 from May 2013). VCA2 works in the opposite direction of VCA1 i.e. the more VCA1's loudness increases the more VCA2's loudness decreases. The panning or crossfading is adjusted with a control knob (manual control) and by two external control voltages, one equipped with an attenuator. Suitable control voltage sources are e.g. LFOs (A-145, A-146, A-147), envelope signals (A-140, A-141, A-142, A-119), random (A-118), Theremin (A-178) or a voltage coming from a MIDI-to-CV-Interface (A-190, A-191). The panning/crossfading is displayed with 2 LEDs.

A-134-1 has an audio input with attenuator for each VCA. If the audio input of VCA2 is not used the audio input of VCA1 is connected with audio in of VCA 2, i.e. the sockets are "normalled". The module has three audio outputs: Left Output (VCA1), Right Output (VCA2) and Mix. For Panning applications the outputs Left Out and Right Out are used. If the module is used as a Crossfader the Mix Output functions as output.

Module A-134-1 enables voltage controlled stereophonic panning effects (one audio signal distributed to two outputs), crossfading effects (two audio inputs mixed to one audio output with voltage controlled loudness proportion) and combinations of both effects.
Read more
 1 in stock $81.71
Click for better price!
quote 716920
36
Doepfer A-141-4 Quad Poly VCADSR Module
Cat: 676693 Rel: 18 Jul 18
 
Quad voltage controlled envelope generator - 8HP
Notes: A-141-4 is a quad voltage controlled Envelope generator and is primarily planned for polyphonic applications. The module contains four ADSR type voltage controlled envelope generators with common manual controls and CV inputs with polarizers for the all parameters Attack (A), Decay (D), Sustain (S) and Release (R). Each of the four envelope generators has available a gate input, a control LED and an envelope output.

The module has these controls and in/outputs are available:

- Attack (manual control)
- Decay (manual control)
- Sustain (manual control)
- Release (manual control)
- CVA control (polarizer for Attack CV input)
- CVD control (polarizer for Decay CV input)
- CVS control (polarizer for Sustain CV input)
- CVR control (polarizer for Release CV input)
- CVA socket (Attack CV input)
- CVD socket (Decay CV input)
- CVS socket (Sustain CV input)
- CVR socket (Release CV input)
- Gate inputs 1 - 4
- Envelope outputs 1 - 4
- LED displays 1- 4 (envelope display)

The output voltage range for each envelope is 0 - 10V.
Read more
 3 in stock $144.57
Click for better price!
quote 676693
37
Doepfer A-180-4 Quad CV Buffer Module
Cat: 714707 Rel: 22 Jan 19
 
4HP Eurorack module consisting of four buffer circuits for control voltages
Notes: Module A-180-4 is a fourfold CV buffer. Buffers are required if the control voltage coming from a CV source shows a voltage drop in case of changing loads or due to other reasons a buffering is required.

For the lower three units the input is normalled to the output of the above unit. That way the module can work as 1-in-4 buffered multiple provided that no signals are applied to the inputs of the three lower units.

Typical applications:

- Buffering the outputs of voltage controlled switches (e.g. A-150-1, A-150-8, A-151, A-152). Comment: in case of bidirectional switches it's not possible to integrate the buffers into the switching module because the direction is not known (i.e. which terminal of the switch is working as input and which as output). All electronic switches suffer from a small residual restistance that may cause a small voltage drop without buffering. This may become a problem especially when VCOs are controlled by the switched voltages.
- Buffering of CV interfaces, quantizers, slew limiter, S&H/T&H, sequencer etc. when VCOs are controlled by the CV (provided that the module in question does not feature a buffered output)
- Buffered multiple (similar to A-180-3)
Read more
 1 in stock $51.07
Click for better price!
quote 714707
38
Doepfer A-111-4v Quad Precision VCO Module (vintage edition)
Cat: 734878 Rel: 09 Jul 19
 
Quad precision VCO - 18HP
Notes: A-111-4 contains four precision VCOs and has individual controls, inputs and outputs for each VCO available as well as a common control and output unit. After all the A-111-4 is very similar to four A-111-3 without LFO mode but built in output mixers for the three waveforms, and a master unit for all four VCOs.

Controls, inputs and outputs for each of the four VCOs:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: ~ 2 semitones / ~ 1 octave / ~ 4 octaves)
- Modulation CV input
- Modulation destination: Upper position: exponential frequency modulation (XM) / Lower position: linear frequency modulation (LM) or pulsewidth modulation of the rectangle (PM), selectable via internal jumper
- Frequency Modulation (FM) or Pulsewidth Modulation of the rectangle (PWM)
- Modulation intensity
- Triangle output
- Sawtooth output
- Rectangle output (about 50% without external PWM)
- Sync input (hard or soft sync internally selectable via jumper, CEM3340 hard sync type)
- CEM3340 based VCO (triangle core)
- Each VCO has it's own separate internal +/- power supply for each for best stability and the prevention of unwanted synchronisation of the VCOs

Controls, inputs and outputs of the master section:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: 2 semitones / 1 octave / 4 octaves)
- Frequency Modulation CV input (FM)
- FM intensity
- Triangle sum output
- Sawtooth sum output
- Rectangle sum output
- As soon as the single waveform output of a VCO is patched this waveform of the VCO in question is removed from the sum (this function can be turned off for each single output socket by means of solder bridges on the pc board, i.e. the sum contains then all signals independent of the patching of the single output)
- CV output (outputs the sum CV that is used to control all four VCOs)
- Bus CV (via jumper, optional, please remove the bus jumper if this feature is not used to avoid unwanted frequency modulation as then the unused CV line of the bus works as a kind of antenna)

Typical applications:

- Fat sounding monophonic VCO with the possibility to adjust any intervals
- Paraphonic patches in combination with the polyphonic CV interface A-190-5 (all four VCOs processed by one VCF/VCA)
- Full polyphonic patches in combination with the polyphonic CV interface A-190-5 and four complete VCF/VCA sections
- Complex VCO patches with up to four VCOs by means of the frequency modulation features (exponential an linear) and the sync functions
Read more
 2 in stock $414.27
Click for better price!
quote 734878
39
Doepfer A-132-8 Octal Poly VCA Module
Cat: 676692 Rel: 18 Jul 18
 
Octal VCA module containing four VCA pairs - 8HP
Notes: A-132-8 is an octal VCA and primarily planned for polyphonic applications. The module contains four VCA pairs. Each pair includes two daisy-chained VCAs. One VCA has a linear control scale, for the second VCA linear or exponential control scale can be chosen by means of jumpers. We decided to provide two VCAs for each voice because usually one VCA is required for loudness envelope and a second one for velocity (or other functions like individual voltage-controlled loudness of each voice, amplitude modulation and so on).

These controls and in/outputs are available:

- Default Gain 1 (GL)
- Default Gain 2 (GX)
- CV Input VCA 1
- CV Input VCA 2
- Audio Input
- Audio Output

In addition, an Audio Sum Output is also available.

The module features two Default Gain controls (GL, GX), that enable the opening of the first VCAs (L) and/or second VCAs (X). For this the controls GL and GX generate two internal control voltages 0...+10V which are connected to the switching contacts of the sockets 1L...4L (control GL) and 1X...4X (control GX). As long as no patch cable is inserted into the socket in question the internal default control voltage (GL or GX) is used to control the corresponding VCA. This is necessary when the VCA in question is not in use (i.e. no external CV available). Otherwise the VCA would close and there would be no output signal even if the other VCA in the chain is open. The controls GL and GX are also useful for testing polyphonic patches (e.g. for tuning the VCOs).

In the factory the CV inputs are adjusted for a CV range 0...+10V - matching to the polyphonic ADSR module A-141-4. But the sensitivity of each CV input can be adjusted by means of a trimming potentiometer to adapt the CVs even to other control voltage ranges.
Read more
 2 in stock $146.66
Click for better price!
quote 676692
40
Doepfer A-106-6 XP Multimode Filter Module
Cat: 692508 Rel: 19 Jun 18
 
Multimode filter based on the filter circuit of the Oberheim Xpander - 12HP
Notes: Module A-106-6 is a multimode filter that is based on the filter circuit of the Oberheim Xpander. The module features 15 different filter types (those filters of the A-107 that were available in the Xpander) with 8 filters available simultaneously. The toggle switch Filter Group is used to switch between 2 filter groups.

These filter types are available:

- 1L (6 dB low pass)
- 2L (12 dB low pass)
- 3L (18 dB low pass)
- 4L (24 dB low pass)
- 1H (6 dB high pass)
- 2H (12 dB high pass)
- 3H (18 dB high pass)
- 2B (6 dB band pass)
- 4B (12 dB bandpass)
- 2N (notch)
- 3A (allpass)
- 2H1L (asymmetrical band pass made of a 12 dB high pass and a 6 dB low pass)
- 3H1L (asymmetrical band pass made of a 18 dB high pass and a 6 dB low pass)
- 2N1L (combination of notch and 6 dB low pass)
- 3A1L (combination of allpass and 6 dB low pass)

The module features voltage-controlled resonance. For filter group 2 (2L, 4L, 2B ...) even self-oscillation is possible.

All standard VCF controls are available: manual filter frequency control Frq, one control voltage input with attenuator (FCV2) and one without attenuator (FCV1, ~ 1 V/octave). In addition, voltage-controlled resonance with manual control (Q) and a CV input with attenuator (QCV) are available.

The circuit is based on a 24dB lowpass filter. The outputs of the four internal filter stages (i.e. the 6, 12, 18 and 24dB outputs) are mixed together with different levels and polarities to obtain 15 different filters. Because of this special circuit the outputs have slightly different levels and noise floor. This is caused by the different internal amplifications and numbers of stages that are required to generate the filter in question. If e.g. a filter is derived by one stage only (e.g. the 6 dB, 12dB, 18dB and 24dB low pass) the noise floor is smaller compared to a filter that is derived by a combination of all four filter stages.
Read more
 2 in stock $135.14
41
Doepfer A-138i Interrupting Mixer Module
Cat: 731945 Rel: 10 Jun 19
 
Multi-featured mixer - 6HP
Notes: Module A-138i is a four channel mixer with an additional mute switch for each input. On top of that it is equipped with two types of single outputs and a dual mix output. All inputs and outputs are DC coupled. Consequently the VCAs can be used to mix both audio and control voltages.

Each input is - apart from the mute switch - equipped with the usual attenuator.

The single outputs offer the attenuated and possibly muted signal of the channel in question. Two version of single outputs are available:

Single Output A: If a plug is inserted into the single output "A" socket the channel in question is removed from the sum signal.

Single Output B: If a plug is inserted into the single output "B" socket the channel in question is not removed from the sum signal. This type of single outputs is available only for the channels 1 and 2.

The output is twice available (two sockets, hard-wired like a multiple).

The distances between the controls and sockets are smaller as for the standard A-100 modules and rubberized small-sized knobs are used. In return the front panel has 6 HP width only. The module is primarily planned for applications where only limited space is available.
Read more
 1 in stock $75.42
Click for better price!
quote 731945
42
Doepfer A-122 VCF3 24dB Low Pass II Filter Module
Cat: 703570 Rel: 05 Oct 18
 
24dB low pass filter based on a Curtis filter circuit - 8HP
Notes: Module A-122 is a voltage-controlled low-pass filter, which filters out the higher parts of the sound spectrum, and lets lower frequencies pass through.

The cut-off frequency determines the point at which filtering takes effect. You can control this manually, or by voltage control (filter modulation, for instance by an LFO). Two CV inputs are available.

The cut-off slope is -24 dB/octave. The circuitry uses a Curtis chip, and is very similar to the classic Oberheim filter sound. Because of its different circuitry and controls, the A-122 has a considerably different sound to the A-120 'Moog-like' filter, especially in the way the resonance behaves.

Voltage controlled resonance: on the A-122, resonance can be controlled not just manually, but by voltages as well, right up to self-oscillation. In this case, the filter behaves like a sine wave oscillator.
Read more
 2 in stock $93.23
Click for better price!
quote 703570
43
Doepfer A-103 18dB Low Pass Filter Module
Cat: 692504 Rel: 18 Jun 18
 
18dB low pass filter based on a modified Moog cascade - 8HP
Notes: Module A-103 is a voltage controlled low pass filter with 18dB/octave slope. The circuit is based on a modified transistor ladder (Moog ladder) and is a reproduction of the legendary TB303 filter.

As for the rest the A-103 is identical to the A-120 Moog low pass filter (same controls, inputs/outputs) only the filter sound is different.
Read more
 2 in stock $78.56
Click for better price!
quote 692504
44
Doepfer A-102 Diode Low Pass Filter Module
Cat: 692503 Rel: 18 Jun 18
 
Reproduction of the legendary British diode lowpass filter - 8HP
Notes: Module A-102 is a reproduction of the legendary low pass filter design that uses diodes in the filter stage as frequency controlling elements - resulting in "strange" resonance behaviour and frequency response, as resonance and frequency are not independent from another.

As for the rest, the A-102 is identical to the A-120 Moog low pass filter, the A-103 (18dB TB303 Filter) i.e. the same controls, inputs and outputs. Only the filter sound is different:

- Manual control of filter frequency
- 3 CV inputs (CV1, CV2, CV3), 2 of them with attenuator (CV2, CV3)
- Input level control
- Resonance control up to self-oscillation (depends upon the frequency setting for the A-102)
Read more
 1 in stock $77.52
Click for better price!
quote 692503
45
Doepfer A-101-3 Vactrol Modular Phaser Module
Cat: 682321 Rel: 30 Apr 18
 
Complex 12-stage phase shifter with separate in- and outputs for all phaser stages
Notes: Module A-101-3 is a 12-stage phase shifter with vactrols as phase shifting elements. Vactrols are known for their smooth sound behaviour. In contrast to other phaser designs, the A-101-3 is much more flexible and offering a lot of new features not available from other phasers on the market. The main difference is that the Doepfer design offers access to each of the 12 input and output stages leading to a lot of new filters that cannot be obtained in other ways. Especially the free patchable feedback loops (yes, not only one feedback loop is possible) between each of the 12 stages, the separate phase shift control for the stages 1-6 and 7-12, and the 2 polarizers intended to control the feedback loops lead to completely new filter types (a polarizer is a circuit that is able to generate positive and negative amplifications in the range -1...0...+1 with -1 = inversion, 0 = full attenuation, +1 = unchanged signal, for details concerning the polarizer function please look at the A-133 VC Polarizer or A-138c Polarizing Mixer module).

Internally, the module is made of 2 independent 6 stage phase shifters (1-6 reps. 7-12) with separate audio inputs (with attenuators), audio outputs (with mix control), and phase shift control units. The phase shift control units feature both manual and voltage-controlled phase shifting (e.g. from a LFO, ADSR, Random Voltage, Theremin CV, Foot Controller CV ...). For each sub-module a phase shift display (LED) is available. The LED shows the illumination state of the 6 vactrols of the sub-module in question as it is connected in series with the internal vactrol LEDs.

Each of the 12 phase shift states is equipped with an audio output socket and feedback input socket to obtain full flexibility to create a multitude of different filters. The audio input signal and the output signals of stage 6 resp. stage 12 are mixed with 2 manual controls to obtain effects at two audio outputs (for normal phase shifting effect this is 50% input signal and 50% phase shifted signal). The two submodules are internally connected via normalized sockets so that two 6 stage phase shifters can be obtained without external patches. Audio output of stage 6 is normalized to audio input of stage 7 and CV input 1-6 is normalized to CV input 7-12. But due to the open structure of the module even other stages than stage 6 and stage 12 can be used as outputs to generate different sounds (simply patch the desired stage output to the normalized mix input socket).
Read more
 2 in stock $259.81
46
Doepfer A-149-1 Quantized Stored Random Voltages Module
Cat: 745776 Rel: 09 Sep 19
 
12HP random voltage generator for Eurorack, with 4 CV outputs
Notes: Module A-149-1 is the first module of the A-149-x range. In this group we present by popular request several functions of Don Buchla's "Source of Uncertainty 265/266" (SOU) modules that cannot be realized with existing A-100 modules. Many functions of Buchla's 265 and 266 SOU can be realized with existing A-100 modules. For details please refer to A-100 patch examples.

Module A-149-1 has available four different analogue random control voltages that are generated in different ways.

The "Quantized Random Voltages" section has available 2 CV outputs: "N+1 states" and "2N states". N is an integer number in the range 1...6 that can be adjusted with the manual control (Man N) and an external control voltage CVN with attenuator. Whenever the rising edge of the input clock signal (Clk In) appears a new random voltage is generated at the N+1 resp. 2N output. The N+1 output is capable to generate N+1 different voltage levels (or states), the 2N output up to 2N different states. If for example N is set to 4 the N+1 output generates up to 5, the 2N output 16 different states. The voltage steps of the 2N output are adjusted to 1/12 V in the factory. Consequently, exact semitones can be obtained in combination with a VCO. The voltage steps of the n+1 output are adjusted to 1.0 V in the factory corresponding to octave intervals in combination with a VCO. For each output a trimming potentiometer is available on the pc board that enables the user to select other voltage steps for the output in question.

Even the "Stored Random Voltages" section has 2 stepped CV outputs available: one with even voltage distribution of the max. 256 output states and second one with adjustable voltage distribution probability. The distribution probability is adjusted by a manual control (Man D) and an external control voltage CVD with attenuator. With the control set fully counter-clockwise most of the random voltages will be low magnitude but even medium and high magnitude voltages may appear but with smaller probability. As the control is turned to the right (or a positive control voltage appears at the CVD input) the distribution moves through medium to high magnitude voltage probability. The symbol at the lower jack socket shows this coherence graphically. The voltage range is 0...+5V for both outputs of the "Stored Random Voltages" section. For each output a trimming potentiometer is available on the pc board that enables the user to select another voltage range for the output in question.

The A-149-1 can be extended by 8 random digital voltages with the A-149-2 Digital Random Voltages module.
Read more
 2 in stock $103.71
Click for better price!
quote 745776
47
Doepfer A-111-4 Quad Precision VCO Module
Cat: 671550 Rel: 29 Nov 17
 
VCO module featuring four precision oscillators - 18HP
Notes: A-111-4 contains four precision VCOs and has individual controls, inputs and outputs for each VCO available as well as a common control and output unit. After all the A-111-4 is very similar to four A-111-3 without LFO mode but built in output mixers for the three waveforms, and a master unit for all four VCOs.

Controls, inputs and outputs for each of the four VCOs:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: ~ 2 semitones / ~ 1 octave / ~ 4 octaves)
- Modulation CV input
- Modulation destination:
- Upper position: exponential frequency modulation (XM)lower position: linear frequency modulation (LM) or pulsewidth modulation of the rectangle (PM), selectable via internal jumper
- Frequency Modulation (FM) or Pulsewidth Modulation of the rectangle (PWM)
- Modulation intensity
- Triangle output
- Sawtooth output
- Rectangle output (about 50% without external PWM)
- Sync input (hard or soft sync internally selectable via jumper, CEM3340 hard sync type)
- Min. 10 octaves range (with appropriate external CV)
- CEM3340 based VCO (triangle core)
- Each VCO has it's own separate internal +/- power supply for each for best stability and the prevention of unwanted synchronisation of the VCOs

Controls, inputs and outputs of the master section:

- 1V/Octave CV input
- Octave switch (+1 / 0 / -1 octave)
- Tune control (range internally adjustable by jumpers: 2 semitones / 1 octave / 4 octaves)
- Frequency Modulation CV input (FM)
- FM intensity
- Triangle sum output
- Sawtooth sum output
- Rectangle sum output
- As soon as the single waveform output of a VCO is patched this waveform of the VCO in question is removed from the sum (this function can be turned off for each single output socket by means of solder bridges on the pc board, i.e. the sum contains then all signals independent of the patching of the single output)
- CV output (outputs the sum CV that is used to control all four VCOs)
- Bus CV (selectable via jumper)

Typical applications:

- Fat sounding monophonic VCO with the possibility to adjust any intervals
- Paraphonic patches in combination with the polyphonic CV interface A-190-5 (all four VCOs processed by one VCF/VCA)
- Full polyphonic patches in combination with the polyphonic CV interface A-190-5 and four complete VCF/VCA sections
- Complex VCO patches with up to four VCOs by means of the frequency modulation features (exponential an linear) and the sync functions
Read more
 1 in stock $385.53
Click for better price!
quote 671550
48
Doepfer A-150-8 Octal Voltage Controlled Switch Module
Cat: 671556 Rel: 29 Nov 17
 
Octal VC/manual programmable switch - 12HP
Notes: Module A-150-8 contains eight manually/voltage controlled switches. Each of the eight switches has a manual control button (Man.), a control voltage input (CV), a common Out / Input (O/I), and two In / Outputs (I/O1, I/O2). The switches are bi-directional, i.e. they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Two LEDs show which in / output is active (i.e. which is connected to the common out / input). In addition, the LEDs are used for the programming of the module:

For each unit the operating mode can be selected: Toggle or Level controlled. In Toggle mode the rising edge of the CV input or operating the manual control button changes the state of the switch. In Level mode the switch state is defined by the voltage applied to the CV input (low voltage = I/O1, high voltage = I/O2) or by the state of the manual control button (not pressed = I/O1, pressed = I/O2). The modes are programmed very easily: Operating the Toggle/Level button of the program section displays the current state of each switch with the LEDs: left LED on = Toggle mode, right LED on = Level mode. Operating the manual control button of the switch in question changes the toggle/level mode while the Toggle/Level button of the program section is operated. During the programming patched CV signals may have to be removed as the CV signals would interfere with the manual operating buttons during the programming process.

In addition, it's possible to define master/slave groups. In such a group the upper unit (= master) controls also the state of the following switches provided that they are defined as slaves. Master/slave programming is also very simple: Operating the Master/Slave button of the program section displays the current state of each switch with the LEDs: left LED on = Master, right LED on = Slave.

When all 8 units are defined as master all switches are independent from each other. If for example the sequence is MSSSMSMS the control unit of the first switch also controls the switches 2, 3 and 4. The control unit of switch 5 also controls the switch 6, and the control unit of switch 7 also controls the switch 8. The current states of the slave switches are overwritten by the state of the master switch.

Technical note: To protect the electronic switches in case of an unsuitable patch (e.g. connection of two outputs) a 1k protection resistor is inserted into the O/I line of each switch. If control voltages used for VCOs are switched this may cause a small voltage drop and lead to undesired audible detuning. For this application we recommend to insert a CV buffer between A-150-8 and the VCO(s), e.g. the Buffered Multiple A-180-3 or the Precision Adder A-185-2. Integrating the buffers into the module A-150-8 was not possible because this would ruin the bidirectionality of the switches.
Read more
 1 in stock $130.95
49
Doepfer A-140 ADSR Envelope Generator Module
Cat: 577754 Rel: 29 Nov 17
 
Envelope generator with CV outputs for modulation - 8HP
Notes: Module A-140 is an envelope generator, and, since it puts out control voltages, counts as one of the modulation devices in a modular system. As soon as the gate input receives sufficient voltage, the ADSR generates a variable voltage, changing in time, called an envelope. This varying voltage is output in normal (positive) and inverted form, and can be used, eg. for voltage controlled modulation of a VCO, VCF, or VCA, or for processing other modules' inputs and outputs.

The shape of the envelope is governed by four parameters: Attack, Decay, Sustain and Release.

The envelope is started (triggered) by a gate signal either from the INT.GATE voltage on the system bus, or, if a signal is put into it, from the gate input socket.

The envelope can also be re-triggered, i.e. start from scratch again, each time a trigger signal is sensed at the Retrig. input socket, when the gate is still open.

Module A-140 has available a three-position toggle switch to select one of three time ranges. The envelope duration ranges from about 50us (microseconds) up to several minutes.

In combination with the Comparator module A-167 a free-running "ADSR-LFO" can be realized.
Read more
 1 in stock $79.61
Click for better price!
quote 577754
50
Doepfer A124 Wasp Filter Module
Cat: 577743 Rel: 29 Nov 17
 
12dB multimode filter module - 8HP
Notes: Module A-124 is a special 12dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies, manufactured by the UK company "Electronic Dream Plant").

This design "abuses" digital inverters as analog operational amplifiers leading to distortions and other "dirty" effects that generate the specific sound of this filter.

The filter is equipped with a band pass output and a combined low/notch/high pass output. For this output a control knob defines the relation between low and high pass signal.

If both signals appear at the same level (i.e. middle position of the Mix knob) one obtains a notch filter. Otherwise the low or high pass signal predominates.

The module does not feature self oscillation in contrast to most of the other filters of the A-100 system.
Read more
 1 in stock $81.71
Click for better price!
quote 577743
Artículos del 1 al 50 de 122 en la página 1 de 3
1  2  3  »

Filter

Bestsellers: All Genres
Show titles sold
Close