All genres charts

Notes: The Beam Splitter is a single pedal meant to create a massive sound. It is three different takes on overdrive, voiced to work together perfectly. Two of them can be delayed in time, and all three can be run in parallel or split out to three separate sources.

Beam Splitter takes a mono input and makes it wildly bigger than before. Things stretch in time and compress in dynamics, and a rich harmonic wash is achieved without sacrificing clarity.

To be washed in sound, does it have to be one big sound, or will a number of small sounds do the trick? To create a wall of sound, same question, but also how does it stay solid? How can sound waves make a wall, and is it just a moment in time; will it always crash down?

Why record your guitar thrice when Beam Splitter exists?

Beam Splitter is best seen in three sections - Purple, Green and Blue.

Purple is a hard-clipping distortion that can be seen as the core gain sound of Beam Splitter.

Of Beam Splitter's three gain sections, it is arguably the heaviest and most compressed. It has three controls, identified by their purple knobs and labels - Gain, Volume and Tone.

Green is an overdrive with both soft and hard clipping. It is the lightest and brightest of the three gain sections in Beam Splitter. Also featuring Gain, Volume controls the green gain circuit features a Time knob, which sets the delay time, up to 125 sections. When blended in parallel with the other drives, this delay time can create anything from tight comb filters to loose doubling delays to short slapback.

Additionally, there is a Decay knob, which sets the feedback of the delay, from one repeat up to many repeats trailing off. In comb filter settings this can increase resonance.

Blue is a transistor Overdrive and the most neutral and reactive of the three gain circuits, with a gain range somewhere in the middle. Its Gain switch sets the amount of breakup. In the down setting, it is less overdriven, with less compression in the mids and highs. In the up setting, it is more overdriven and aggressive. It also boasts Time and Decay controls, on top of the Tone and Volume knobs and gain switch.

The pedal's Deviate control is a shared knob that sets the amount of random variation in the delay time of the Blue and Green drive sections. The more it is turned up, the farther their delay times can deviate, and the faster those deviations happen. When at zero, the delay times are fixed, above zero, each Time knob sets that sections delay time.

Deviate intends to create a more realistic sense of doubled players, with random variations in timing as if you were playing to the track twice. It can also give the impression of flanging, chorusing or broken vibrato, depending on the settings.

The Expression jack is used to externally control the Deviate knob using a TRS expression devices with standard polarity and tip connected to the wiper.

Beam Splitter has a mono input. From there the signal goes out to Purple, Green and Blue drive sections in parallel. If only plugged into the Purple Out Jack, all three sections will join in parallel mono at that Output. Green and Blue can each be broken off into their own output by plugging into the corresponding Out jacks.

In this way you can have a full 'stereo' setup.

Notes: Little box, big reverb. Specially designed for huge, cavernous echo effects and ideal for infinite tails and frozen sounds, the Blackhole is an exceptionally high quality pedal at a very reasonable price.

Supplier's Notes:
Create haunting echoes, ethereal landscapes and otherworldly ambience with Blackhole, a reverb pedal as big and as mysterious as the cosmos. Blackhole takes you there - beyond the ambience of mere earthly Halls, Rooms, Plates or Springs. Blackhole will take you on a journey from cathedral-type spaces to a universe of out-of-this-world soundscapes.

It includes onboard tone controls, modulation, and infinite reverb settings with mono or stereo operation, MIDI control, preset storing, and most importantly a new compact, easy-to-use interface.

Blackhole features two types of infinite reverb. Infinity mode continuously layers new sound on top of a suspended reverb. Freeze mode holds the effect allowing you to play over the reverb tail. The Freeze Footswitch allows instant access to this feature.

Unlike other reverbs which may offer pre or post modulation, Blackhole features modulation built into the reverb structure itself. It's essentially a big multi-voice chorus, with unique tone-shaping ability. You can utilize extreme settings to smooth out the edges.

Like all Eventide pedals, Blackhole allows you to fine tune every aspect of the effect. With a new, user-friendly, intuitive interface, just about anyone can shoot for the moon and land beyond the stars.

Input: 1/4" TRS / Mono = Tip, Stereo = Tip & Ring
Out 1: 1/4" TS Mono / Mono Output
Out 2: 1/4" TS Mono / Stereo Output
EXP: 1/4" TRS / Expression pedal, Aux Switch or MIDI I/O
Mono/Stereo Switch: Sets Input to Mono (Tip) or Stereo (Tip + Ring)
Guitar/Line Level Switch: Optimizes internal gain structure
Mini USB Software updates, MIDI I/O
DC Input Jack: 5.5mm / 2.1mm plug / Center Negative (-)

Input Impedance: 700k ohms Mono, 990k ohms Stereo
Max Input, Guitar: +8dBu
Max Input, Line: +14dBu
Output Impedance: 220 ohms
Recommended Load Impedance: 10k ohms

Power: 9V DC @ 200mA / Center Negative (-)
Dimensions (product): 4" W x 4.25" D x 1.68" H / 102 mm x 108 mm x 43 mm
Weight (product): 1.06 lb / 0.48 kg
Dimensions (package): 7.7" W x 4.75" D x 2.8" H / 178 mm x 121 mm x 71 mm
Weight (package): 1.68 lb / .77 kg

Notes: HI POWER is Crazy Tube Circuits' next endeavour in pedal + amp-in-a-box overdrives recreating legendary sounds, following the success of Crossfire and Unobtanium.

It was inspired by the sonic combination of two British tone machines. The almighty Colorsound Power Boost meets the blistering high-headroom Hiwatt amp.

While the combination of these two units directly hints at the gear setup of David Gilmour and especially the gear used on Pink Floyd's album: Wish You Were Here (think the guitar solo sounds of "Shine on you Crazy Diamond", "Have A Cigar") the sonic options are endless.

The orange enclosure silicon transistor circuit (Colorsound Power Boost) can deliver from a transparent clean boost to an all-out fuzz driving a tube amp to sonic bliss. Crazy Tube Circuits set out to clone the original unit featuring the true-to-the-original spec BC184 transistors running on 18V DC (via an internal voltage booster circuit).

The ultra-flexible 2-band Baxandall EQ circuit can add bite and low-end rumble to any setup. Crazy Tube Circuits used a reverse log gain pot (labelled as volume), compared to the linear taper pot found in the original units and acted as an on/off switch, to be able to set the amount of boost/overdrive more precisely. While the earlier units didn't feature a master volume control (only as an aftermarket mod - Pete Cornish made an external unit master volume for David Gilmour's Power Boost) Crazy Tube Circuits chose to include one that is setup in a way so that when it is all the way clockwise it is bypassed. Later versions of the Power Boost had 9V power supply and were renamed as the "Overdriver" due to the lower headroom and their ability to drive the signal earlier. They were offered in a grey enclosure and can be seen in the gear setups of Jeff Beck, Marc Bolan, etc. Crazy Tube Circuits chose to incorporate this version as well with a flip of a toggle switch (PWR-ODR toggle switch).

On the left side of the HI POWER you will find an all-analogue circuit set out to emulate the sound and feel of a Hiwatt amp. Following the path of the famed British tube amplifier, this circuit offers authentic amp tone and feel resembling guitar tones from guitar greats like David Gilmour, Pete Townsend, Jimmy Page, Noel Gallagher to name a few. From the big bold high-headroom clean sounds to the face-melting crunchy tones.

True to the last detail, Crazy Tube Circuits have included the full EQ section along with a presence control located at the negative feedback of the power amp simulation circuit. A headroom toggle switch selects between the high headroom 100w power section provided by a quartet of EL34s (think Hiwat DR103), or the lower headroom and compression provided by a 50W power section with a pair of EL34s when hit hard (think DR504). Similar in operation to the original amps the master volume was designed to produce more gain at higher settings.

Crazy Tube Circuits taken the design a step further by adding a switch to select between input channels of the amplifier. You can select between the full response of the normal channel of the amplifier, the increased presence and tight low end of the bright channel input or the "Gilmour-ish" enhanced frequency response and added gain of those inputs linked together. This follows the modifications that Pete Cornish did to all David Gilmour's Hiwatt amps.

Like their other dual overdrive/amp-in-a-box designs, Crazy Tube Circuits also included a passive effects loop to give you the option to connect your beloved pedals between your booster/overdrive and amp in a box or use the two sections as separate and independent effects when using an external bypass switcher/looper. Gilmour enthusiasts will love to insert their Big Muff, Tube Driver and Phase 90 in there. Note that all pedals inserted in the passive effects loop are still in the signal chain when any or both sections of HI POWER are in bypass.

HI POWER features a power-up bypass/engage pre-set function for the footswitches. That way you can select which state your pedal will go to when you plug the power supply. This function comes in especially handy to people that use remote pedal switchers / loopers as they only set the state of the pedal once and then operate from the controller.

All-analog dual booster/overdrive - amp in a box.
Recreates the tones of the legendary setup used by David Gilmour in the recordings of Pink Floyd's Wish You Were Here album.
Right side: Faithful reproduction of the Colorsound Power Boost/Overdriver circuits with true-to-the-original-spec BC184 transistors.
Controls: gain, bass, treble, master, voicing toggle.
Wide gain range control: from transparent boost to gnarly and fuzzy overdrive.
Two-band (treble & bass) Baxandall EQ.
Master knob sets overall output. Huge amount of dB boost available.
Toggle switch to select between the 18V Power Boost style circuit or the 9V Overdriver style circuit.
Left side: Hiwatt AMP in a box overdrive.
All analog simulation of the preamp and power amp sound and response.
Controls: gain, bass, middle, treble, master, input channel toggle switch, headroom toggle switch.
Gain control: from clean to big bold British crunch/overdrive.
3-band Hiwatt style EQ (bass, middle, treble).
Presence control follows the original design/is located at the negative feedback of the power amp simulation circuit to control the amount of upper mid and high frequencies.
Master knob sets overall output volume. Designed to respond like the original control producing more gain at higher settings.
Input channel toggle switch selects between normal, bright, or linked input channels of the AMP for different voicing and gain levels.
Headroom toggle switch selects between the high headroom and dynamic response of a 100W amp or the lower headroom and compression of a 50W power amp.
Independent operation of the BOOST/OVERDRIVE and AMP sections
Click-less true bypass design via high-quality relays for each section.
2 Footswitches / 2 Status LEDs - one for each effect section.
Power-up bypass/engage preset function for the footswitches.
Top-mounted jacks
Passive series effects loop to connect pedals between the two sections or use them separately as independent effects.
Power Supply: Use only 9V DC, 2.1 mm x 5.5 mm, center negative (not included).
Runs internally at 18V DC (via voltage doubler circuit) for higher headroom and tube-like performance.
Current consumption: 84mA.
British Racing Green die-cast enclosure with color-coded lettering for the control section (orange for BOOST/OVERDRIVE section, white for AMP section).
Dimensions: (W x L x H): 119 x 97 x 53 mm.
Weight: 444 g.
Made in Greece.

Notes: Transform your electric guitar into a sitar!

Very few instruments offer as much harmonic and dynamic flexibility as a sitar. Electro-Harmonix has streamlined the essence of the sitar into a compact enclosure that offers a polyphonic lead voice and tuneable sympathetic string drones that dynamically react to your playing. With the EHX Ravish Sitar Emulator, you can create your own custom scales for the sympathetic strings while you set the decay time for the lead voice.

Two expression pedal inputs allow you to bend the pitch of the lead voice and control the volume of the sympathetic strings simultaneously. These unique controls offer the player the ability to program the Ravish to become a totally unique and organic instrument unto itself.

The Ravish is a truly new design with the flexibility to be a crossover tonal wonder.

Download free Ravish settings

Transform your electric guitar into a sitar
Lead sitar voice tracks your notes polyphonically with a wide range of tonal possibilities
Selectable decay speed for the Lead voice
Sympathetic string drone simulation with a wide tonal range
Selectable keys and scales including major, minor and exotic provided for the Sympathetic strings
Power adapter included

Specifications

Circuit: Digital
Bypass: Buffered Bypass
Audio: Mono
Power Supply: 9.6VDC-200mA power adapter included
Dimensions (in): 5.75 x 4.75 x 2.5
Current Draw: 160mA
Year Released: 2011

Notes: The TRIO+ is a simple-to-use guitar pedal that listens to the way you play and automatically generates bass and drum parts that match your song. Just plug your guitar into the TRIO+, press the Band footswitch to teach the TRIO+ your chords and rhythm, then press the Band footswitch again to start playing with your own personal band! Bass and drum levels can be adjusted for the perfect mix using the TRIO+'s Bass and Drums knobs. The TRIO+ also features a Simple Bass button lets you select between 3 bass line modes for busy or simple bass lines. Pushing the Band Creator™ paradigm further, the TRIO+ also allows you to loop and custom sequence your looped guitar parts to create full songs on the fly. Press the TRIO+'s Looper footswitch to record a loop along with an unlimited number of overdubs. The Loop level can be individually controlled using the TRIO+'s Loop knob. Loops can be recorded by themselves, operating just like a traditional looper, or along with the band. You can also apply built-in effects to your guitar signal by enabling the TRIO+'s Guitar FX button, or connect your favorite effects to the TRIO+'s FX Send and FX Return jacks. The TRIO+ provides 12 music genres to choose from including Blues, R&B, Rock, Alternative Rock, Metal, Pop, Electronic Pop, Hip-Hop, Country, Folk, Latin, and Jazz. 12 song styles are available for each genre and can be selected using the TRIO+'s Style encoder, including selection between 3/4 and 4/4 time signatures. Multi-colored LEDs around the TRIO+'s Style encoder indicate which styles best match your song. The TRIO+ can learn up to 5 different song parts, perfect for creating an intro, verse, chorus, bridge and outro. Song parts can be recalled on-the-fly as the song plays back or pre-programmed as a sequence for automated playback. An optional DigiTech FS3X Footswitch can be connected to the TRIO+'s Control In jack for additional handsfree control with 3 modes of operation to select from. Up to 12 songs along with loops can be stored to the TRIO+'s Micro SD Card (included). Need to create more songs? No problem. Just insert a new SD Card and you're ready to start teaching the band your new songs. To manage all your songs and loops on a computer, download the free Librarian Manager software from digitech.com, available for Windowsr and Macr. The TRIO+ offers independent Tempo, Genre, Style, Loop Level, Bass Level, Drums Level, Headphone Output Level controls; Guitar, FX Return and Control Inputs; Amplifier, Mixer, FX Send and Headphone Outputs; Built-in Guitar Effects (relative to music genre); a Soft Click Footswitch and includes a 9V DC adapter.

General Specifications
ControlsTempo, Genre, Style, Loop, Bass, Drums, Headphone Volume
Backlit ButtonsGuitar FX, Seq, Part 1-5, Alt Time, Song, Simple Bass
FootswitchesLooper, Band
LEDsGenre types, Style 1-12, Audiolastic, Looper, Band
JacksPower, Control In, Guitar In, FX Return, FX Send, Amp Out, Mixer Out, Headphone
OtherMini USB port, microSD card slot
Bit Depth24-bit
Sample Rate44.1 kHz
Signal-To-Noise Ratio110dB, A-weighted
Maximum Recording Time230 seconds per song part i based on a minimum 50 BPM and 48 bars per part
USB TypeMini-B
SD Card TypemicroSDHC, Class 10
SD Min/Max Storage Size8 GB/32 GB
Power Requirements9 VDC external power adapter
Power Consumption7.2 W
Current Draw800 mA
Dimensions
Length5.4"
Width4.25"
Height2.5"
Weight1.46 lbs.
Audio Output
Amp Output TypeUnbalanced, 1/4" TS
Amp Output Impedance1 kO
Mixer Output TypeUnbalanced, 1/4" TS
Mixer Output Impedance1 kO
FX Send Output TypeUnbalanced, 1/4" TS
FX Send Impedance1 kO
Headphone Output Type1/8" (3.5 mm) Stereo Mini Jack
Headphone Output Impedance120 O
Audio Input
Guitar Input TypeUnbalanced, 1/4" TS
Guitar Input Impedance1 MO
FX Return Input TypeUnbalanced, 1/4" TS
FX Return Impedance1 MO
Control Input Type1/4" TRS (compatible with DigiTech FS3X)

Notes: A Re-envisioning of the Filter Effect

Turning its predilection for parallel signals toward the world of filters and widening out to full stereo, Old Blood Noise Endeavors unveils its first digitally-controlled analogue pedal. Float boasts two independently controllable filters and copious capabilities for motion. Utilising the two filters in tandem can create stereo movement, linked reactive elements, and modulations that approach harmonic tremolo and phaser, as well as classic filter sounds.

Old Blood Noise were familiar with some aspects of the filter pedal. But the slow dual motions, the controls that go a little more left than you expect, the parallel undulations and surely other corners were all left unexplored.

So, turning their predilection for parallel signals toward the world of filters and widening out to full stereo, say hi to Float, the new Dual Moving Filter pedal! As OBNE's first digitally-controlled analogue pedal, Float boasts two independently controllable filters and copious capabilities for motion.
Utilising the two filters in tandem can create stereo movement, linked reactive elements and otherworldly psychedelic modulations. The two independent filters can be set to either low pass, band pass or high pass. The core of each filter is its Cutoff Frequency, which can stay still or move via either its 6 different LFO shapes or through its dynamic Envelope triggering.

The envelope sections can unleash quacky auto-wahs, shooting sonic laser beams or organically rising and falling filter landscapes - all triggered by your playing. While the LFOs lets Float become a mind-bending modulation device that can become everything from a phaser, a harmonic tremolo, a choppy or bubbly step-filter or an automated synth-like sweeper. However, skip the Modulation or envelope sections and the dual sliders come into play. This allows you to use Float as a dual-band EQ for subtle to extreme tone shaping, as a manual filter for on-the-fly futuristic filter sweeps or even for old-school wah-tones. Each filter also sports a resonance control, allowing you to unearth velvety smooth filters, vocal-like formants, screaming sonic squelches and anything in between.

All of this is pretty familiar, but also pretty sweet. Like an amalgamation of all things filtery and good. But where things start to get really different and really fun is when you mess with the Sync and Routing of the two filters. By flicking that tiny toggle labelled Sync to On, the two filters will move like tonal twins - locked in, precise and uniform. This lets you create robotic sequencer-like textures, trippy dual modulations or ultra-long, yet perfectly timed, filter manoeuvres. You can also set it to Off and have them completely free-rolling for organically weaving textures or full-on filter cacophonies. In addition, the filters can be run in either parallel mono, series mono or stereo for all kinds of refined dual movements, cascading filter chaos or lush and dreamy stereo sweeps.

To round off this veritable filter playground, we've added an expression in port, that lets you take hands-free control over either the cut-off frequency or LFO Rate, allowing you to keep your fluttery filter modulation as expressive as the music you play.

So, that's Float... or that's the essence of Float. You'll unlock sounds from this thing that you never knew it was capable of, because it does a lot of good, weird, wild, tame, ugly and absolutely stunning stereo stuff. Float on, friends!

Notes: Another banger from Dreadbox's excellent effects series. Stereo echo effects based around multiple hybrid delay stages, giving bags of character for reverb, modulation effects and classic delays.

Supplier's Notes:
Dreadbox Raindrops is a Hybrid Delay/Pitch Shifter/Reverb pedal that takes the concept of short echoes to a different level.

It is equipped with multiple delay stages and different chips and you can choose between 3 different play modes, where in each one you can have a whole new experience and alternative soundscapes. You can achieve from simple short echoes, to long, dirty and lo-fi delays and from simple pitch shifting bursts to extensively lasting reverbs.

Specifications

Circuit: Analogue Dry signal / Hybrid Delay / Digital Reverb
Bypass: Buffered OpAmp
Audio: True Stereo IN/OUT
Inputs / Outputs: TS Unbalanced 6.4mm jack
Power Supply: 9VDC BOSS style center pin negative 2.1mm (NOT INCLUDED)
Dimensions (cm): 14 x 10 x 5.6
Current Draw: 220mA

Notes: For Eons, man has thought the sound of thunder to be from the heavens above, echoing boastfully over us as we stay safe from its greatness. However, legend tells of a stoic and indomitable beast residing in the highest mountains seen and heard only by the most brash of travelers. With gnarled and twisted horns, this creature emits a sound thicker than Earth's crust to command attention and warn all who stand in his way. This is Eons.

Eons is a five-state fuzz capable of massively thick sounds ready to test the limits of any amp's grill cloth. Use the Voltage (lightning bolt) knob to crank up to 18 volts into the pedal's circuit for massive, open fuzz sounds, or choose to starve it down to 3 volts for spatty, gated fuzz. Experiment with the Voltage and Mode knobs for nearly endless styles of fuzz tones. Find vintage-inspired sounds emanating from the stages of Woodstock to chaotic three-chord punk rock. Eons is ready for a fight.

The Eons features a five-position rotary knob that offers the following clipping configurations. Think of them as different "flavors" of the pedal:
I. Silicon soft clipping traditional fuzz that's well rounded with a huge sound; compressed and smooth.
II. Silicon clipping with an added bass boost that boosts the low end at the beginning of the circuit; compressed and crunchy.III. Germanium soft clipping with a feel of "what if a distortion and fuzz had a kid?"; crunchy and dynamic.
IV. LED clipping diodes with a slight high-end cut; dynamically dark.
V. Hard clipping silicon transistors combined with LED and Silicon soft clipping diodes. The rowdiest of the modes with tons of gain: compressed, loud, and angry.

Specs

The Eons comes in a sandy tan enclosure color with red, cream and black ink. Artwork features a stoic four horned, Markhor goat illustrated by Adam Forster.
9V DC, center negative, 100mA min
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended. Power supply not included.

Notes: This is a digital effects pedal in a compact format, including reverse delay - pitch shifter - delay and modulated reverb.

Effects engine is 12 bit and includes analogue filtering before and after digital conversion, based on vintage eighties units' topologies, but it allows for all the effects to be simultaneously available.

Despite its complexity, operation is simple and intuitive, all functions are directly controlled by the corresponding knob.

Pots controls:

1-Blend controls mix of effects over final output signal
2-Octave blend mix a pitched signal to the input of the reverb
3-Octave -1 +1 controls tuning of pitch component
4-Repeat controls feedback of delay component 5-Balance controls mixture from reverb and
delay.
6-Sample rate controls the frequency operation for the whole pedal, modifying delay time
and reverb decay.
7-Reverse blends the reverse component with the direct signal.

Indicators:

Signal: indicates clipping, the input path has compression and limiting so it gives an idea of how hard you are driving the pedal.

Tap: blinks at the rate of the delay, depending on tap and sample rate.

Tap/freeze: turns red while tapping time, blue indicates reverb freeze.

Bypass: global effect on/off

Footswitches:

1-Tap/ freeze works as a tap tempo for the delay and reverse delay, and freeze/infinite for reverb, selected by the associated toggle switch. Max delay time is around 6 seconds, depending on sample rate setting.

2-Bypass: buffered bypass for the whole pedal.

Power consumption: 150 milliamps.

Notes: Transform your guitar into a classic organ from the '60s and beyond!

With 9 presets that were finely tuned to emulate the most legendary organs from the '60s and beyond, the EHX B9 Organ Machine will transform your guitar or keyboard. Control the instrument's signature percussive click and sweet modulation. Blend your dry signal to create lush layers. Enough tonewheel and combo organ inspiration to light your fire and cook up some green onions!

Transform the tone of a guitar or keyboard into that of a convincing full body, electric organ
9 presets that were finely tuned to emulate some of the most popular and classic electric organ tones
Control over percussive attack level, modulation speed, organ and dry volume
Rugged and easy to use
Power adapter included

Specifications

Circuit: Digital
Bypass: Buffered Bypass
Audio: Mono
Power Supply: 9.6VDC-200mA power adapter included
Dimensions (in): 4.75 x 4 x 2.25
Current Draw: 100mA
Year Released: 2014

Notes: Transform your axe and resurrect the sound of vintage tape-based keyboards!

Now any electric guitar player can have access to nine magically quirky, dark and unique Mellotronr sounds. No more extra devices such as special and cumbersome 13-pin MIDI pickups! In addition to electric guitar, you can trigger the MEL9 with any instrument that produces an electrical output, such as a keyboard or a bass, down to 55 Hz or A1.

The polyphonic EHX MEL9 has superior tracking; you can create single notes or chords with ease. The MEL9 will follow guitar bends, dive bombs, slurs, and any other guitar expression/performance techniques you can throw at it!

Pays homage to nine of the coolest Mellotronr sounds: Orchestra, Cello, Strings, Flute, Clarinet, Saxophone, Brass, Low Choir and High Choir
Works on guitar without modifications, special pickups or MIDI implementation and tracks bends, slides, even whammy dive bombs!
Also works with bass guitar down to the open A string as well as keyboards within the limits of its polyphony (5 notes) and range (A1 to A5)
Includes independent Effect and Dry volume controls so you can create the perfect mix at the Effects output
Dry Output jack outputs your input signal at unity gain
Attack control sets the volume swell speed. As it's turned clockwise the notes fade in more gradually
Sustain control adjusts the release time after a sound is stopped. As it's turned clockwise, the fade out time increase
Power adapter included

SPECIFICATIONS
Circuit
Digital
Bypass
Buffered Bypass
Audio
Mono
Power Supply
9.6VDC-200mA power adapter included
Dimensions (in)
4.75 x 4 x 2.25
Current Draw
100mA
Year Released
2016

Notes: Seriously potent effects power as usual from EarthQuaker. Octave reverb with clever modulation options and eight different modes, from sub-octave generation to pitch-bent harmonies.

Supplier's Notes:
Unrelenting, radicalized reverb for the modern world; an array of haunting, unearthly delights and ethereal sonic sorcery designed to take you on a deep journey through both time and space. This is your new destiny should you choose to accept it. Welcome to your new Astral Destiny.

The Astral Destiny is a compact and powerful modulated octave reverb pedal that features 8 reverb modes with 8 editable presets, assignable expression control, tails for natural reverb decay when the effect is bypassed and a super cool stretch feature that doubles the length of the reverb while adding an adjustable pitch bending effect.

Astral Destiny features a completely analog dry signal path, totally digital delay path, buffered bypass with and two different bypass states- Tails or Full Bypass. Tails Mode, which the is the pedal's stock setting, allows the reverb to naturally decay after the effect is bypassed, slowly letting you drift back from your ethereal dream state into the waking world. Full Bypass, on the other hand, will cut the reverb effect completely when the effect is bypassed and instantly throw you back into cold clutches of reality.

Let your fate spin out of control by pressing the Stretch footswitch doubles the length of the reverb effect while adding a temporary change in pitch. While a short tap will immediately change the pitch, holding the Stretch footswitch depressed gives you a temporary pitch bending effect with the speed of the of the pitch bending effect created by holding the Stretch footswitch easily adjusted by turning the Length knob.

While the Astral Destiny offers two different modes of operation, it ships in Live Mode, where each control will operate manually, laying out your fate for you, clearly visible. Preset Mode in contrast lets you chose from one of the 8 unearthly, ethereal factory preset reverb fates, 1 for each reverb mode, the Astral Destiny comes with. Each of these can be edited or completely overwritten just like when the ancient Fates plucked or cut the strings of ones destiny. Save settings for Length, Depth, Rate, Tone, Mix as well as EXP assignment and Stretch length and recall them instantly. Any of the Astral Destiny's 8 reverb modes can be used as the basis for each of the 8 presets.

But beware! - There is no undo for preset saving, so make sure you are not overwriting your favorite sound, especially when you are saving presets from Live Mode! - Once the string of your fate is cut, there is no turning back on your destiny. Freely express any aspect of your Astral Destiny - Shipping with the EXP jack mapped to the Depth control, the expression control can also be swiftly assigned to Length, Rate, Tone, or Mix, plus different EXP assignments can be saved in each preset and you can also use Control Voltage with the EXP Jack.

Each Astral Destiny is built one at a time by a team of Los Angeles-based robots and a handful of real life humans in the occupied Erie territory presently known as Akron, Ohio.

Notes: Seeking to recreate the sounds of the Klon Centaur overdrive pedal and Dumble guitar amps, the Crazy Tube Unobtanium combines the holy grails of germanium diodes and all-analogue amp-in-a-box tone. Incredible value.

Supplier's Notes:
Introducing the Unobtanium, a rare sonic element born out of legendary tones.

A mythical overdrive meets the tone and feel of two iconic amplifiers. Crazy Tube Circuits have accurately recreated the circuit of the high headroom overdrive with the magic blend of clean and overdriven tones and added extra features for versatility. The amp-in-a-box section uses an all-analogue circuit to capture the essence of two legendary D-style tube amplifiers. From tube-like compressed fat clean to sweet singing overdrive with blooming harmonic overtones. Combine both sides for near infinite smooth sustain and enter sonic bliss while a passive series effects loop gives you the option to connect your beloved pedals between the overdrive and amp section, building your ideal rig

Right side: K-style pedal overdrive circuit including the fabled germanium diodes
Controls: gain, treble (tone), volume, bypass mode and clipping / compression
Wide gain range control: from transparent boost to high headroom overdrive
Treble control is an active circuit to boost or cut treble
Volume knob sets overall output. Huge amount of dB boost available
Toggle switch to select between the original buffer bypass to add clarity and run long cables or
true bypass
Toggle switch to select between stock clipping / compression or enhanced gain and
headroom/output

Left side: D-style Amp in a box overdrive
Controls: gain, emphasis, tone, volume, amplifier voicing toggle
Gain control: from clean boost to sweet singing overdrive
Emphasis control is a pre-drive EQ to control presence and bottom end response
Tone knob controls the amount of post overdrive high end frequencies
Volume knob sets overall output. Match bypassed volume or use as a clean boost or preamp
Toggle switch selects between 2 distinct D-style overdrive circuits
SSS: clean and transparent overdrive with natural organic compression
ODS: higher gain overdrive with enhanced mid frequencies and harmonic overtones
External footswitch input to select amplifier voicing (bypasses on board toggle switch)
Internal trimmers adjust EQ and volume boost of D-style overdrive voicings

Features:

Dual overdrive with independent operation
Two legendary sonic elements combined in one device
Passive series effects loop to connect other pedals between the two sections or use them separately
Runs internally at 18V DC for higher headroom and tube-like performance
Exceptional pick attack response - almost infinite smooth sustain when both sides are combined
Top mounted jacks
Click-less True Bypass design via high quality relay
Power Supply: Use only 9V DC center negative power supply (not included)
Current consumption 83mA
Pebble grey die-cast enclosure with black ink in old school type print
Made in Greece

Notes: Eventide's Riptide pedal is the result of extensive research into overdrives and Uni-vibes. With stereo overdrive and Vibe, each effect features dual voicings versatile enough for funky bright tones to explosive and warm lead tones.

The Vibe knob delivers classic Hendrix-style Uni-Vibe to full-on vibrato perfect for modern soul and lo-fi tones. With the power to engage each effect individually, swap the order, and store presets, Riptide makes it easy to get caught up in the excitement.

Drive features a balanced distortion with superb dynamics and touch sensitivity. Use the "Green" voicing for a classic transparent overdrive or activate the "Red" voicing for a tight modern overdrive.

Features:

Five presets loaded at your feet with dozens more available by software update in Eventide Device Manager
Dual-action Active Footswitch is latching or momentary
Rear panel Guitar/Line Level switch for matching impedances with guitar, synths, FX loop, or DAW interface
Map any combination of parameters to an Expression Pedal
Use a single Aux switch to Tap Tempo or a triple Aux switch for easy preset changing
MIDI over TRS capable
Multiple Bypass options: Buffered, Relay, DSP+FX or Kill dry
Catch-up mode helps dial in your sound when toggling between presets/parameters
Eventide Device Manager PC or Mac application for software updates, system settings and creating/saving presets

Notes: Inspired by the vintage Bell and Howell 385 Filmosound projector that guitarists have modified and used as guitar amps, Walrus has created a dynamic and responsive overdrive modeled after the projector's tone.

The 385 was developed to have the same simple but effective tone control as it's older relative, but unlike the projector, the 385 breaks up the single tone control and integrates separate, boost and cut bass and treble, allowing the player to get more creative with mid-frequency scoops and bumps allowing for a much wider array of tones to be achieved.

The pedal is internally running at 18v, which helps us nail the same dynamic feel of the amp in a stomp box.

This means it is extremely sensitive to how hard you dig in - just like the amp.

Updated for 2023.

Controls:

Bypass: Soft touch, relay true-bypass. Press the switch to engage/disengage the pedal. LED indicates whether the circuit is engaged or not.
A/B: Soft touch switch. Press to swap between using either A (White) or B (Red) Volume and Gain controls. LED indicates which controls are being used - White for A, Red for B.
Volume A: Controls the overall volume in the A setting. Turn clockwise for more volume, counter-clockwise for less volume.
Gain A: Controls the overall gain in the A setting. Turn clockwise for more gain, counterclockwise for less gain.
Volume B: Controls the overall volume in the B setting. Turn clockwise for more volume, counter-clockwise for less volume.
Gain B: Controls the overall gain in the B setting. Turn clockwise for more gain, counterclockwise for less gain.
Treble: Used to adjust the level of the treble frequencies. Turn clockwise to increase the level of the treble frequencies. Turn counter-clockwise to reduce the level of the treble frequencies.
Bass: Used to adjust the level of the bass frequencies. Turn clockwise to increase the level of the bass frequencies. Turn counter-clockwise to reduce the level of the bass frequencies.
385+ Switch: When the switch is down, you are able to achieve classic 385 sounds. Flip the switch up to add an additional gain stage to the input of the pedal, achieving heavier gain sounds and driving the pedal harder.

Specifications

The 385 comes in a matte black finish with yellow and red ink featuring original artwork of a vintage Belle and Howell 385 projector by David Huttner ready to give you the dynamic tone you've been searching for.
The die cast enclosure's exact size is 12.1 x 6.6 x 3.5 cm
Power requirements are 9VDC (100mA minimum). The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended. Power supply not included.
Input: 1/4" TS, Unbalanced, 1M impedance
Output: 1/4" TS, Unbalanced, 10k impedance
True Bypass

Notes: Analogue Ring Modulation Pedal With LFO, MOD, Frequency & RATE Controls.

Reviving An Avant-Garde Pedal For Music's Trailblazers

From light Lo-Fi modulation all the way to the piercing sound of infinity ring-modulation, the Warm Audio RingerBringer accurately recreates the ultimate all-analogue ring modulation effect used for experimental tones. Like the original, loved by artists like Jeff Beck, Radiohead, Omar Rodriguez-Lopez, Trent Reznor, and many more, RingerBringer delivers the original distinct set of controls, extensive in/out options, and rich sonic textures to inspire boundless sonic experimentation.

Don't Just Play, Create

The ideal platform for the sonic tinkerer, RingerBringer inspires you to generate layered frequencies and harmonics, explore a wide range of sonic possibilities for guitar & beyond, and design your own sounds from the ground up. Extensive controls including LFO, MOD, Frequency & RATE open up sonic possibilities that range from subtle overdriven textures all the way to wobbling, warped leads soaked in texture and tone. RingerBringer is 100% analogue and sports premium components including hand-selected op-amps and transistors. RingerBringer is no emulation or "patch", instead it delivers true-to-spec performance of the boutique, analogue original.

For Original Artists Building Memorable Sounds

Delivering tones ranging from nuanced drive to out-of-this world modulation, RingerBringer helps develop a unique sonic signature for any instrument, on any track.

A Sandbox For Synths & Keys:

Send any keyboard or synth through the WA-RB for added harmonic content and endless modulation. Try sending digital synths, keys, and pads from your interface through the WA-RB for added analogue vibe and "fattened up" tone on otherwise dry digital signals.

Technical Specifications

100% Analogue Ring Modulation Pedal With LFO, MOD, Frequency & RATE Controls
Accurate Recreation Of The Ultimate Ring Modulator For Experimental Tones
Premium Components Including LM13700M & TL072ACDR Op-Amps + Hand-Selected Transistors (DMMT3906W & MMBT3904) For True-To-Spec Performance
LFO Controls: Amount, Rate, & Sine/Square Wave Switch
Modulation Controls: Mix, Frequency, & Lo/Hi Switch
Universal Drive Control + LED Indicators For Level, LFO, & Bypass
CV Inputs: Rate | Amount | Mix | Frequency
1/4" Input Jacks: Audio In | Audio Out | LFO Out | Carrier IN/Out
Output Impedance: 600 Ohms | Buffered Bypass
9-Volt Battery Or /External 9V Regulated (Centre-Negative) DC Adapter
Nominal Current Draw: 100 mA (9V)
Custom Black Panel Enclosure With Retro Faux-Wood Sides
Dimensions: 6.5" x 5.25" x 3" | Product Weight: 1.90 lbs

Notes: The EHX 1440 Stereo Looper is a compact powerhouse that provides 1440 seconds of high-quality, uncompressed, stereo recording time plus the ability to store 20 different loops. It can even tempo sync to an external MIDI device and is packed with features you'll want. Unlimited overdubbing means you can lay down as many parts as you like while variable tempo playback plus Reverse and Octave speed effects really enhance creative control.

A 1 Shot function is also included, adjustable fadeout times and optional external footswitch control for selecting loops and Undo/Redo. The affordable 1440 Stereo Looper puts a ton of looping power on your pedalboard.

Notes: Introducing a new addition to the DigiTech Whammy Family -- Whammy DT! We've taken the premier pitch shifting effects pedal added drop tuning and true bypass to bring you the ultimate Whammy pedal, the Whammy DT. With the Whammy DT, you can modify your tuning without having to change guitars or pause awkwardly to make adjustments for the next song. Key changes are at the tips of your toes and take just moments, which is crucial when the audience is feeling your vibe. Pitch shifting effects really help your guitar performance stand out and the Whammy pedal has been the core pitch shifting effect for famous artists for over 20 years. Now add full drop and raised tuning in addition to classic Whammy shifting to your effects arsenal and find out why the Whammy DT is the premiere pitch shifting effects pedal for every guitarist.

General Specifications
D/A Conversion24 bit
Pitch Bend Range+2/-3 Octaves
Detune Range-4 to -30 cents
Drop Tune Range1-7 Semitones, Octave, Octave + Dry
Power Consumption2.6 Watts (< 288 mA @ 9 VDC)
Power Adapter9 VDC External Adapter
Sample Rate44.1 kHz
Frequency Response20 Hz to 20 kHz
Signal to Noise Ratio> -105 dB (A weighted); ref = max level, 22 kHz bandwidth
THD0.004% @ 1 kHz; ref = 1 dBu w/ unity gain
Dimensions
Height2.36"
Width8.2"
Depth7.73"
Audio Output
Output Type1/4" Unbalanced TS
Max Output Level+10 dBu
Output Impedance1 kO
Audio Input
Instrument Input Type1/4" Unbalanced TS
Max Input Level+5 dBu
Input Impedance1 MO
MIDI Input5-Pin Din
Footswitch Input1/4" TRS - for use with optional FS3X Footpedal

What's in the box?
1 x Whammy DT Pedal
1 x Power Supply

Notes: The Bitmap is a bitcrusher with fractional bit reduction and sample rate modulation. The Bitmap 2 adds waveshaping, wavefolding, and a window comparator for extreme digital distortion. A drive control handles everything from single coil guitars to synthesizers, with +8 dBu maximum signal level and enough gain to sound like an overdriven mixer channel. Modulation and envelope control create dynamic, responsive distortion and digital artifacts.

The Bitmap 2 is tuned to provide maximum sustain without sputtering on staccato notes. Less extreme settings add layers of nonlinearities that interact in subtle ways, giving you the warmth and grit of 8- and 12-bit samplers. Sample rate reduction turns your guitar into 8-bit video game sounds or twists scales into inharmonic melodies. Sample rate modulation adds subtle motion or morphs your guitar into entirely new textures.

The Bitmap works with guitar, bass, synthesizers, drum machines, and other instruments or line level sources.

Size:3.05" x 4.75" x 2.5"
Input impedance:1 MO
Output impedance:< 1 kO
Bypass: analog buffered
Power: 9 VDC, center negative
Current: 250 mA

Notes: The ultimate metal tone? An evolution of the brand's excellent Wurm distortion with the addition of an ultra-fast VCA-based noise gate, ideal for HM-2-inspired chainsaw tones. Heavy.

Supplier's Notes:
Fusing together the powerful evolution of KMA's highly regarded Wurm Distortion with an intuitive, yet versatile and ultra-fast Noise Gate, Guardian of the Wurm is the perfect metal monster. From chugging hard-rock, droning doom metal and grinding Swedish death metal, the beast abides. But through its highly tweakable control set, the pedal can be tamed to provide impeccable clarity to your riffs, making this the definitive dirt pedal for metal, prog-rock, shoegaze, indie and beyond.

Power by opt. 9 V PSU (9 V DC, centre -, 2.1 mm, >150 mA max. current draw)

Notes: Atlas Compressor

The Atlas Compressor offers a comprehensive collection of compression circuits that perfectly capture the tone and feel of the industry's most sought-after compressors. Straight out of the box, Atlas delivers six different styles of compression, ranging from classic stompbox compressors like the now-discontinued Diamond Optical Compressor to high-end rack units such as the snappy 1176 compressor and the smooth and gentle LA2A optical compressor. Atlas also features advanced dual-band compression, which provides an independent set of controls for both the high and low frequencies. Each compression engine has onboard controls for Threshold, Ratio, Attack, Release, Output, Tone, and Blend, allowing for fine-tuned control over the compact One Series hardware.

A History Lesson in Compression

The Atlas is packed with so many different types of compression that it could serve as a tour guide through the history of compressor equipment. First stop: classic stompbox squashers such as the legendary the Dan Armstrong Orange Squeezer and the excellent (but discontinued) Diamond Compressor. Next stop: universal and ubiquitous studio rack gear like the smooth and gentle LA2A optical compressor and the ultra-responsive 1176 FET compressor. Finally, we're taking you to all-out nerd territory with Peak, RMS, VCA, and Dual compression, and an onboard Expander circuit... the Atlas has it all and does it well.

Optical Rack

The Optical Rack compressor engine is based on the legendary LA2A studio opto compressors from the early 60s. Optical compression controls its output level with light. Increasing the incoming audio level in the original units caused an electro luminescent panel to shine brighter. A photo resistor monitors that light panel and decreased the audio output level, as the panel got brighter. The result is a very smooth and gentle attack that imparts a full-bodied and natural sound on guitar, bass, or vocal. This compressor sounds great with clean strummed or arpeggiated guitar lines as well as acoustic guitars.

Studio 76
The Studio 76 compressor is based on the 1176 studio rack compressors of the late 60s and early 70s. This solid state FET compressor is known for its full body and super-fast attack. All of the attack times in 1176 compressors clock in at less than a millisecond. Studio 76 is a great compressor for fast and aggressive country pickin' (think Johnny Hiland), slap bass, slide guitar and much more.

Cubic Zirconia

The Cubic Zirconia was inspired by opto compressors that use an LED in place of the LA2A's electro luminescent panel. This technology is usually what you find inside effects pedals. Using an LED as an optical compressor's light source creates faster attack and release times, which generate artifacts that tend to make the compression sound a bit dirtier. This is a great sound for playing tight and funky riffs on the guitar.

Studio snap

A very aggressive and modern sounding compressor. It's based on hard-knee, VCA feed forward type compressor. It uses two compressors in parallel to handle both RMS level controls ("Root Mean Square" compression means that the compressor will react according to the "average loudness") AND the peaks. The combination of these two compression approaches gives STUDIO SNAP its character.

Dual band

The Atlas has two independent compressors that can be routed in a number of different ways. They can run in Series Mode (one running into another). They can also run in Parallel Mode and be mixed together with a Crossfade control. The Dual Band compressor runs in Band Split Mode, which is a version of parallel routing where one compressor controls only the higher frequencies (everything above 333Hz) and the other controls the lower frequencies (everything below 333Hz). With the Dual Band Compressor the high frequencies release faster than the lower frequencies, so as you sustain a chord the low frequencies remain compressed while the second compressor releases the high frequencies. The result is a beautiful blooming effect that accentuates high harmonics. This is a great compressor for slow ringing chords or lead lines with long sustained notes.

Includes 9v DC power supply (300mA / Negative Tip)
Includes 1/8" to 1/4" cable for Neuro Mobile App connection.
Power Consumption - 165mA
USB port - Connects to Mac or Windows PC for firmware updates and the forthcoming in-depth effects editing software.
Brushed anodized aluminum housing.
Dimensions: L: 4.5 in./11.4cm x W: 2.75 in./7cm x H: 2 in./5.1cm (including knobs)

Notes: Bags of character courtesy of 'tone wizard' Andy Timmons (Danger Danger). Dual delay lines work in tandem, creating stereo effects from vintage tape delay to infinite hold.

Supplier's Notes:
Andy Timmons' mysterious sounding "Halo" effect is a modulated dual echo sound that has long been kept a secret by the tone wizard himself. Andy spent decades combining and crafting the sounds you can now get from the HALO. Notes from the HALO dance rhythmically, almost creating a reverb diffusion. Those notes are held together with tape-style effects like modulation, saturation and compression. The results are stunning!

The pedal comes loaded with his signature delay tone and you can program your own sounds and save them as presets. Easily bounce between Side A and B on the fly, essentially giving you two delay pedals in one. In addition to Andy's signature "Halo" sound, there are numerous other rhythmic delays including: quarter note, dotted 8th, stereo rack mount analogue delay, and a vintage multi-head tape echo. Stunning stereo and pristine sound quality are further enhanced with controls for saturation, tone, and shelving filters that give you the ultimate delay pedal.

Think of HALO as two delay pedals that work in tandem, letting you switch between your main delay (side A) and an alternative (side B). With up to 1500 ms of available delay, set sides A and B for different delay times, then simply foot switch between the two. Keeley's Smart Stomp System allows you to press and hold either stomp switch to engage tap tempo mode. Press and hold the alternate stomp switch for infinite repeat/hold.

Each Preset bank gives you 2 delays settings for a total of 8 user-storable effects. Use the Rhythm control to select between different echoes like HALO, Analog, Tape, Quarter and Dotted Eighth. HALO's Saturate control adds tape compression texture to your tone. The Tone and High Pass Filter controls your overall delay shape and mix. The Rhythm Mode selector delivers 5 delay types, including Andy's unique "Halo" sound. Set the Time and Feedback controls low, and you can open up a world of ambient chorus and flanger effects.

Run the HALO in stereo for incredible true-stereo imaging or save your favourite combination of settings as a preset and the HALO becomes an incredibly compact multi-effect workstation!

Notes: The #1 EQ pedal returns - better than ever

Empress Effects have brought back the most sought-after Parametric EQ pedal, with groundbreaking upgrades.

Everything people loved about the original ParaEq was kept, and more fidelity and control have been added.

More Control

Whether you're trying to cut through a mix or fix a feedback issue, you need precision! The ParaEq MKII offers the most control of any pedal EQ on the market.

More Sweetness

Effortlessly sweeten your tone with beautiful sounding, super smooth Baxandall filters for broad high and low frequency shelving adjustments on the Deluxe.

More Power

The ParaEq MKII pedals operates internally at 27V, providing clean headroom without unwanted clipping.

More Purity

This pedal is able to offer the most control without degradation to the tone due to minimal circuit topology00-the opposite of graphic EQs.

Why Choose Parametric EQ over Graphic EQ?
Parametric VS Graphic EQ Graph
Graphic equalizers provide a convenient visual sense of the EQ curve. However, there is a tradeoff in transparency and precision.

The graph here shows the ParaEq MKII Deluxe (cyan) and a 7-band graphic EQ pedal (magenta) both providing a +4dB boost at around 2 kHz. As can be seen, the ParaEq is much more precise in the changes it can make, whereas the graphic EQ affects nearly the entire frequency spectrum. Furthermore, at around 10kHz the ParaEq is providing unity gain, whereas the graphic EQ is attenuating the signal by nearly 6dB. This makes the ParaEq a more transparent circuit than the graphic EQ.

This combination of transparency and precision is why recording studio control rooms are dominated by parametric equalizers, and why they're a great choice for creative and corrective EQ on your pedalboard.

Which ParaEq Do You Need?

The original ParaEq has been loved and trusted by musicians on a variety of instruments for over a decade. Both the ParaEq MKII and the ParaEq MKII Deluxe feature a low-noise, transparent signal path that is extremely versatile.

With three fully parametric bands, you can simultaneously achieve broad tonal shaping and precise fine-tuning to sculpt your perfect sound.

The ParaEQ MKII Deluxe will appeal to players who:

Need high-pass and low-pass filters for precision work at the frequency extremes
Want the glorious sound of Bandaxall filters for sparkling high end or extra weight in the low end
Want to be prepared for any EQ situation

Specifications

Input Impedance: 1MO
Output Impedance: 100O
Frequency Response (-3dB): 22Hz - 25kHz
Total Harmonic Distortion: < 0.05%
Noise: > 107dB
Headroom: +30dBu
Input Voltage: 9VDC Centre-Negative
Required Current: 300mA
Power Input Connector: 2.1mm Barrel Connector
Height (Enclosure Only): 1.5"
Height (Including Controls): 2.5"
Length: 3.5"
Width: 4.5"
Weight: 1lb

Notes: Distortion and reverb meet in this unique pedal, sporting a joystick to tweak the sound and the option to flip the order of the two effects in the signal chain. Simple, quirky and effective.

Supplier's Notes:
Walrus Audio give you the two most quintessential effects that yield unruly amounts of power and influence to an instrumentalist: reverb and distortion. They have been harnessed and woven together for an eternity of ethereal power with The Melee: Wall of Noise. The Melee unapologetically uses a joystick to meld reverb and distortion into one massive blaze of sound. With the flip of the order switch, run the distortion into the reverb or reverb into distortion; signal chain is your call now. For the explorer, the Melee can run one of three different reverb programs Ambient, Octave, and Reverse.

In a less is more approach, Walrus Audio have intentionally decided on controls that are fun to use and will inspire a wealth of creative output. Use the joystick to control the amount of distortion by moving it up and down. Moving the joystick left and right will adjust your reverb mix. The tone and decay toggles have low, medium, and high settings. Modulation can be added to the wet signal by holding down the bypass switch and moving the decay toggle. The left position is no modulation, the middle is a slight modulation, and the right is a high modulation.

Algorithms

The Melee is equipped with three different reverb programs, which can be changed by simultaneously pressing the bypass and sustain stomp switches. Experiment with the order toggle switch to hear how differently these all react in front and after the distortion!

Ambient Reverb (Pink LED) - Huge reverb capable of massive trails and engulfing your chords into an angry wash of sound. Great for soaring melodic lines or shoegaze-driven chord progressions.
Octave Down Reverb (Yellow LED) - Similar to the Dark mode in the Slo, you'll find an eerie lower octave hovering in the reverb trail for a nice and dark atmospheric touch.
Reverse Reverb with Feedback (Blue LED) - Add reversed reverb trails back into your signal, create gentle melodies or push into reverse feedback overload. Big, slow, and sad chords love to hang out here.

Momentary

Press and hold the sustain switch to ramp up the reverb trails. Release and the trails will ramp back down to where the decay switch is currently set. The sustain switch can also latch in all three programs. Press and release the Sustain switch to capture and sustain the current reverb decay for long pad-like sounds in your wet mix. Press again to release the latch, and the reverb trail will taper off based on the position of the decay knob.

Specs

The Melee comes coated in a glossy neon pink enclosure with white, yellow, and green inks with art by
David Huttner.
The die-cast enclosure's exact size is 3.62" x 4.79" x 3.14" (including joystick height).
Three bypass modes, DSP, DSP + True, True Bypass
Power requirements are 9VDC, centre negative (200mA minimum).
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended.
Power supply not included.

Notes: Psychdelic Vocal Trip

Designed for vocals, the Echo Master is a lo-fi, analogue tape-style delay unit that can transform your voice into a chaotic realm of noise and feedback. The effects loop allows additional effects to be placed in the signal chain, making it easy to use with any of your favourite effects pedals on your vocal sound without any adapters.

The Echo Master is not just a delay unit, however. It utilizes matched Bourns transformers on the input to create a vibrant-sounding and feedback-minimizing preamp to bring you phenomenal vocal quality before you even hit the PA. Your sound engineer will hate you because you'll sound better than ever without their help. Top it off with high-quality Neutrik XLR jacks and the Echo Master is the ultimate tool for taking total control of the sound of your voice.

Controls

Time: Controls the delay time, with numbers labelled in milliseconds. In the Red Zone, the delay chip is pushed to the extreme. The signal decreases in fidelity as the time increases.

F-Back: Controls the number of repeats in the delay circuit, anywhere from one to an infinite to a wall of oscillation.

Mix: Controls the level of the delayed channel in comparison to the dry signal, from fully dry to an equal mix.

Send/Receive: Plug out of the Send jack into any additional effects, then back into the Return jack to introduce new sounds into your vocals. This loop is before the delay line, allowing you to affect your dry vocals as well as the delay generated by the Echo Master.

*Alternate Backplate: Back in stock baby! The Echo Master can also be purchased with a backplate that mounts to your mic stand. Puts the pedal within hands reach to maximize live performance tweak-ability. This recently upgraded V3, comes with a handgrip screw for more torque (although it resembles the V1, this is a much sturdier model). **Please note- cords, microphone, and stand are not included.

Specifications

Dimensions: 6.09" x 3.45" x 2.75" (including hardware).
Weight: 16oz. (w/ Alternate Back Plate 30oz.)
Power: 9V (runs on standard 2.1mm negative center 9V adapter).
Current Draw: 25 mA.

Notes: An 'otherworldly' take on the classic delay pedal from Death By Audio, with the addition of a fuzz circuit allowing you to dial in grit and texture as well as ethereal atmospheres with shimmering feedback.

Supplier notes:
Lush Modulating Echo

A powerful, ethereal, and nuanced delay pedal with otherworldly controls. Push the feedback for vast worlds of colourful sound. Introduce a bit of warble with the modulator for ghastly chorus tones, or a ton of it to absolutely warp the delayed signal. Once your delay is thoroughly contorted, turn up the fuzz and pulverize it into repeating, shattered pieces. This is the preferred echo for recording engineers and touring pros around the world because, simply put, it just sounds that good. From delicate, beautiful sounds to yawning voids of fuzz and feedback, the Echo Dream II is ready to transform anything you throw at it.

Controls

Master: Sets the overall volume.
Fuzz: Sets the amount of gain, from clean to fuzzed-out bliss.
Delay: Sets the volume of the delayed signal.
D Time: Controls the delay time (numbers shown in milliseconds) between 20 ms and 1 second. Long delay times can create flutter, noise, and distortion.
FBack: Controls the feedback of the delays, from slapback to wild runaway oscillation.
Left Toggle: Up for clean blend, down to kill the dry signal and hear only the repeats.
Speed: Controls how fast the modulator runs.
Depth: Sets how far the modulator will swing the delay time. At high intervals, the pitch of the repeats will shift several semitones!
Right Toggle: Up for a smoother modulator waveform, down for a sharp, square-shaped wave.

Specifications

Dimensions: 5.87" x 4.72" x 2.35" (including hardware).
Weight: 21 oz.
Power: 9V (runs on standard 2.1mm negative center 9V adapter or included 9V battery).
Current Draw: 40 mA.

Notes: Unearth the Walrus Audio Silt Harmonic Fuzz, a collaborative creation with tube expert Jim Hagerman.

Wielding an internal pre-amp tube, the Silt is a two-in-one fuzz that creates massively rich fuzz tones perfect for chords and rhythmic parts or with the press of a switch, adds uniquely harmonic overtones to the signal before hitting the tube. Crafted specifically for those seeking a harmonically rich fuzz experience, the Silt boasts an analogue circuit with the distinctive warmth of a 12AU7 tube as its drive section, letting you explore a unique and wild sonic landscape.

Main Features:

1. 12AU7 Tube Drive

The Silt's 12AU7 tube section drives the warm, bone-rattling fuzz. We unearthed this sonic fossil to encase your sound in an amber warmth, while still providing the grit, growl, and harmonically complex textures that only a tube-driven fuzz can provide.

2. Harmonic Mode

Harmonic Mode acts as a frequency doubler before the drive section of the pedal. This produces crispy, octave-like sounds, lending a unique edge to your lead tones. Try this with your guitar tone knob rolled off.

3. Contour Control for Precision Tone Sculpting

Refine your fuzz tones with the precision of the Contour control to achieve a wide spectrum of timbres.

Toggle between highpass, flat, and lowpass curves in the pre-tube EQ stage, like uncovering layers of sonic strata. Especially helpful when switching between different styles of pickups. Whether you're chasing searing leads or wooley rhythm, the Silt adapts to your style with roaring precision.

4. Designed for Operation at 9v-12v for Plenty of Gain

Supercharge your fuzz experience by operating the Silt anywhere between 9v and 12v. Running the pedal at 12v will give you an extra gain boost, letting you push the primal boundaries of fuzz to deliver the searing tones you've been searching for.

5. True Bypass Circuit

Maintain the integrity of your original tone with the relay bypass circuit. When disengaged, the Silt ensures your signal remains pure, allowing your guitar's natural voice to shine through undisturbed.

Controls:

Volume: Control the output volume level of the pedal.
Tone: Sculpt your output tone with a lowpass/highpass tilt tone control.
Gain: Control the input gain into the fuzz circuit, from subtle, distortion-like crunch to full-throttle fuzz.
Contour: Toggle between highpass, flat, and lowpass curves in the pre-tube EQ stage.
Bypass Switch: Enable or disable the effect with the relay bypass switch, preserving your original signal when the Silt is not in use.
Harmonic Switch: Activate or deactivate the frequency doubler circuit before the clipping stages, infusing your sounds with octave-like textures for a unique sonic edge.

Notes: Music's best octave pedal in a powerhouse pico package!

EHX's smallest and most powerful compact Polyphonic Octave Generator yet. The Pico POG takes the streamlined simplicity of the Micro and Nano POGs and fits it all into an ultra-compact chassis and adds a powerful tone control. The tightest octave effect now fits on the tightest of pedalboards.

The EHX Pico POG features a lighting fast feel that will track every note and chord you play with precision. Dial in Sub Octave to add stumble rumble or monstrous thunder. Add Octave Up for ethereal air or max it out to shred into another galaxy. Perfectly blend 3-voice tones for fat synthy madness. The 3 mode Tone control lets you tailor your sound to fit into any pocket no matter how massive or small.

Controls on the Pico POG include dedicated volumes knobs for the SUB OCTAVE, OCTAVE UP, and DRY voices. These three controls act as a mixer for infinite possible voice mixes. The TONE knob features three modes controlled by the FILTER button. In Tone Mode, the knob acts as a tilt-EQ with a flat frequency response in the center, more treble and less bass as you turn the knob clockwise, and less treble and more bass as you turn the knob counterclockwise. In this mode, the EQ is applied to all 3 voices. In Low Pass Filter mode, the knob cuts highs in the Sub and Octave Up voices, while High Pass Filter mode cuts lows in the Sub and Octave Up Voices.

Lightning-fast tracking with perfectly precise octave tones

3 volume knobs control level of SUB OCTAVE, OCTAVE UP, and DRY tones

TONE knob with 3 filter modes

Tone Mode applied tilt-EQ to all output

Low Pass Mode applies a resonant low pass filter, which allows low frequencies to pass while cutting higher frequencies of the Sub and Octave Up voices

High Pass Mode applies a high pass filter, which allows high frequencies to pass while cutting lower frequencies of the Sub and Octave Up voices

Power adapter included

Specifications

Circuit: Digital
Bypass: Buffered Bypass
Audio: Mono
Power Supply: 9.6VDC-200mA power adapter included
Dimensions (in): 3.65 x 2.0 x 2.0
Current Draw: 100mA
Year Released: 2023

Notes: Tweaking the platform of their Fault overdrive/distortion, Old Blood Noise have carved out room for greater gain range, voice control, and clipping options in the Fault Version 2. The Fault remains a great overdrive with footswitchable second gain stage and three band EQ, and now excels as a clean boost and tweakable high gain distortion as well.

Notes: Amazingly versatile phaser business in this brilliantly designed pedal. Watch the demo video to hear the amazing range of sounds this one can do. Best phaser ever? Might just be.

Supplier's Notes:

Jump into spaceship Horizont and begin your trek into star- filled galaxies, all while discovering the incredible vastness of the sounds created by this inter-dimensional multi-spatial stereo analog JFET Phaser. The unexpected is waiting for you behind the far away horizon and it will be a journey you'll never forget!

The Horizont's mission is to push way beyond the classic phasing sounds of yesteryear, and take you to uncharted phaser worlds the second you plug in. By combining lush analog JFET phasing with digitally controlled dynamics, Horizont creates a vivid and expressive modulation experience, all while providing experimental and creative features that'll kick phasing well into the 21st century.

Besides the more common phaser controls, the Horizont offers a plethora of new and exciting options for all the interstellar tone chasers out there. To greatly broaden the range of phasing tones available, KMA implemented a digital LFO with no less than eight different waveforms: Ramp Up/Down, Sine/Triangle/Square wave, a sweeping waveform, Sample & Hold and a random slope waveform going from 20s down to 40ms.

The implemented envelope generator is one of Horizont's absolute key features. It transforms your input signal into a control source to modulate the speed of the digitally controlled LFO or lets you manually phase for a resonant touch wah- like sound, depending on the state of the SWP- and SPURTCONTROL-Switch.

Set the SPURTCONTROL switch to LFO to let the SPURT knob adjust the internal phasing speed. However, by flicking the switch to ENV (Envelope) mode, it allows you to dynamically modulate the speed along the full LFO speed range, based on how loud the input source is (e.g. when you attack the strings hard). You can also combine the SPURT knob and the envelope by flicking the toggle to LFO+ENV where SPURT then sets the minimum speed. For even more control, you can even plug in an external expression pedal/CV-source (0-5V) to alter the minimum speed on-the-fly or you can use the TAP TEMPO switch (tap just twice) to set the speed to fit in with the tempo of your music.

The EXP-Mode switch also lets you choose between a manual phasing mode, controlled by an expression-pedal or an external CV source. Setting the EXP-Mode switch to the middle position will disable any external expression control.
The SWP (Sweep) switch lets you decide to use either the LFO or the envelope of your instrument signal to control the phasing.

The envelope can be set to upwards or downwards operation via the ENV switch, seeing the LFO either slowing down or speeding up, or flipping the orientation when phasing manually from lows to highs and vice versa. In conjunction with the FUEL (Sensitivity) and the DECAY controls, the envelope can be tailored perfectly to your needs.

The EMPH (Emphasis) mode from the original Astrospurt Phaser was kept, but have reworked and refined it extensively for the Horizont. The four toggle-switches determine the stage in which the phase-shifted signal is fed back into itself, while the REG (Regeneration) control sets the feedback amount. We also smoothed out the overall sound of the EMPH mode for a more pronounced, and crisp vocal-like tone. Each of the different switch variations and turn of the REG control will yield different results, seeing you discover new wild, fuzzy and noisy galaxies as you travel deeper down this sonic wormhole.

In order for you to levitate through spacetime, a stereo output has been added to the Horizont. You can switch between a standard stereo output or a panning output, via the STEREOPAN switch. Synchronized with the LFO speed, the upper cycle of the LFO sends the signal to the OUT1 and the bottom cycle to the OUT2. This is without a shadow of a doubt the most liquid and astonishing phasing experience you'll ever embark upon. But wait, there's more! Stop and take a deep breath, set the MIX control to fully clean and the Horizont is transformed into a Tremolo on-the-spot, with all the other aforementioned features.

Last but by no means least, the Horizont was equipped with an FX-Loop right in front of the phase-shifting line. This enables you to add your own secret sonic weapons to this spaceship, seeing you create your very own unique phasing sounds.The pedals' headroom was also increased drastically by boosting the internal circuit voltage to 18V, from the regular 9V input, to give the cleanest phasing possible no matter what instrument or line source you use.

Notes: The EHX 22500 is a stereo looper with two independent loops that can be played in sequence or in parallel. Flexible performance controls and creative effects allow you to loop in any way you imagine. It records high quality, non-compressed audio directly to a removable SDHC card (4 to 32 GB) and each card holds up to 100 individual loops. Includes an 8GB card for up to 12 hours of recording time.

Creative controls over looping functions such as adjustable tempo, programmable loop/overdub length, and two loops that can playback independently or locked to one another makes the 22500 act like the looper of your dreams.

Download free drum loops for the EHX 22500

Dual stereo loops with independent or locked loop lengths
Sequential looping mode enables verse/chorus switching
Parallel looping mode allows simultaneous playback of two loops
16 built-in drum loops
Selectable microphone input with phantom power
Reverse and Octave functions
Undo-Redo your last overdub or recording
Quantize or non-quantize (free running) modes
USB port enables backup/restore to PC or Mac
Programmable third footswitch for Stop or Tap Tempo
Optional external Loop Up/Down Foot Controller
Power adapter included

SPECIFICATIONS
Circuit
Digital
Bypass
Buffered Bypass
Audio
Stereo
Power Supply
9.6VDC-500mA power adapter included
Dimensions (in)
5.75 x 4.75 x 2.5
Current Draw
235mA
Year Released
2015

Notes: A truly super tremolo with powerful controls and signal routing.

Sculpt the tremolo's shape with adjustable sine, triangle and pulse waveforms while tap tempo and tap divide ensure synchronicity.

Create your own rhythmic patterns and store them.

Save and recall up to eight customized preset programs.

Conjure moving tremolos on-the-fly with EXP control over Rate, Depth, Shape, Phase or Volume. Deluxe I/O lets you choose stereo in/out, mono in/stereo out, stereo in/mono out or mono in/mono out operation.

Analog circuitry yields warm, lush tone that will envelop you in shape shifting waves.

*UK 230V power adapter included*

Notes: Multi-tap delays go next-level with Eventide's incredible heritage distilled into this compact pedal format. Line level options allow you to process synths, drums, guitars and just about any other signal.

Supplier's Notes:
A Multiverse of Tone UltraTap is a unique multi-tap effect pedal capable of rhythmic delays, glitchy reverbs, huge pad-like volume swells, and extraordinary modulation.

It's the perfect tool for staccato leads, swelling chords, and other evolving effects - everything from reversed reverbs to the sound of ripping it up in the Grand Canyon!

Think of UltraTap as the mother of all Echoplexes and you won't be too far off.

That's basically how it operates but with the flexibility to add as many 'tape heads' as you want and expressively control their positions and levels.

UltraTap's controls make possible new and unexpected effects. The controls that you would expect in a multi-tap delay pedaliNumber of Taps, Delay and Feedback- are just the basics.

Controls for Spread, Slurm, and Chop open up a new world of possibilities.

Effect Features:

"Slurm" An exclusive and innovative control that smears/slurs taps together to create truly unique reverbs and choruses.

"Chop" and "Spd/Rise/Rel" combine to allow unusual and expressive modulation of the taps based on LFO shapes or the audio's envelope.

"Feedback" unlocks further tone shaping capability.

"Taps" selects up to 64 taps to create simple repeats or morph delays into chorus and reverb.

"Spread" controls the 'distance' between' taps. With the knob centered, the taps are equally spaced, turn clockwise and the later taps are bunched together, counterclockwise and the early taps are bunched together. Use this control to dial in the perfect rhythmic space between taps.

Onboard LFOs and envelopes to chop the sound source into stuttered rhythms.

"Tap Footswitch" allows you to set the tempo of the taps.

Connectors:

Input: 1/4" TRS / Mono = Tip, Stereo = Tip & Ring
Out 1: 1/4" TS Mono / Mono Output
Out 2: 1/4" TS Mono / Stereo Output
EXP: 1/4" TRS / Expression pedal, Aux Switch or MIDI I/O
Mono/Stereo Switch: Sets Input to Mono (Tip) or Stereo (Tip + Ring)
Guitar/Line Level Switch: Optimizes internal gain structure
Mini USB: Software updates, MIDI I/O
DC Input Jack: 5.5mm / 2.1mm plug / Center Negative (-)

Analog I/O:

Input Impedance: 700k ohms Mono, 990k ohms Stereo
Max Input, Guitar: +8dBu
Max Input, Line: +14dBu
Output Impedance: 220 ohms
Recommended Load Impedance: 10k ohms

Specifications:

Power: 9V DC @ 200mA / Center Negative (-)
Dimensions (product): 4" W x 4.25" D x 1.68" H / 102 mm x 108 mm x 43 mm
Weight (product): 1.06 lb / 0.48 kg
Dimensions (package): 7.7" W x 4.75" D x 2.8" H / 178 mm x 121 mm x 71 mm
Weight (package): 1.68 lb / .77 kg

Notes: The Nemesis Delay is the culmination of three years of intense research, listening, and engineering. The mission was to create a compact, powerful, and easy-to-use delay pedal with unrivaled tone, flexibility, and style. Nemesis offers 26 distinct effect engines ranging from vintage tape and analog delays to highly advanced pitch-shifting, reverse, filter modulating, and rhythmic delays. It also features 128 presets, multiple delay taps, a hold function, tap tempo, full MIDI control, deep editing functionality with the Neuro Mobile App, and much more.

Nemesis captures the full spectrum of delay effects, starting with a comprehensive collection of meticulously crafted vintage delay tones. The Source Audio engineering team spent over a year studying numerous iconic and sought after tape and bucket brigade delay units with a staunch dedication to identifying their every nuance and idiosyncrasy. The Nemesis's Tape, Noise Tape and Slapback delays capture all the characteristic flutter, warmth, and color that give vintage tape delay machines like the Echoplex and Space Echo their classic charm. The Analog delay engine beautifully achieves the resonant peaks combined with high and low frequency decay that typifies classic bucket brigade delay pedals. The pedal's Digital delay manufactures pristine, high definition repeats with or without filtering effects for a classic rack-system tone.

At the opposite side of the spectrum, you'll find an advanced collection of sophisticated and specialized delay effects. The Shifter delay generates perfect polyphonic pitch intervals with repeats jumping to either an octave (up or down), major or minor third, 4th, or 5th. Sweeper applies modulating filter effects to repeats for a unique delay/wah hybrid tone. Backwards effects like Helix and Reverse provide a perfect blend of chaos and control with multi-tap reverse patterns and angelic pitch shifting effects. A Rhythmic delay features an engaging and musical collection of non-standard multi-tap delay patterns.

The 12 engines included on the face of the Nemesis represent a perfect cross section of delay effects, from classic essentials to the highly progressive. But don't stop there, we strongly recommend connecting your Nemesis to the Neuro Mobile App or Neuro Desktop Editor and checking out the 14 additional delay engines not accessible with the effect selector knob. Click the links below for deep-dive videos on some of these bonus delay effects, plus a closer look at the original 12.

Includes 9v DC power supply (300mA / Negative Tip)
Includes 1/8" to 1/4" cable for Neuro Mobile App connection.
Power Consumption - 200mA
USB port - Connects to Mac or Windows PC for MIDI control of firmware updates.
Brushed anodized aluminum housing.
Dimensions: L: 4.5 in./11.4cm x W: 4.5 in./11.4cm x H: 2 in./5.1cm (including knobs)
Wieght: 1 lb./0.45 kg.

Notes: Echolution 3 is a multi-tap stereo modulation delay offering a myriad of sound design options including reverse, jump, pong, modulation tempo sync, variable low pass filter, flexible signal routing and comprehensive MIDI control. Delay times ranging from 100ms to 5 seconds can be dialed in using the Time knob or via Tap Tempo using the left footswitch. A second delay tap can be set to the same length or a fraction of the main delay time to create rhythmic echoes. The ¾ fraction creates a dotted eight note delay, while the Golden fraction uses the sacred geometry of the Golden Ratio (.382) as the multiplier for the second tap. The multi-tap settings can be even further enhanced by the stereo ping pong effect, which causes the different delay taps to switch sides on each repeat. Store up to 4 presets, unlock hidden features with the Universal Remote footswitch, and design yet unheard delay lines. Runs on standard 9VDC.

KNOB-BY-KNOB
Time: Sets the length of the delay line. Overrides tap tempo and vice versa. Select sub-divisions with the small push button. Can activate any two sub-divisions at once.

Mix: Sets the volume level of the delay signal.

Repeats: Sets the amount of regeneration in the delay line.

Mod: Select and set the modulation Speed, Depth, and Tone. Hold push button to sync Speed to tap tempo.

Preset Select: Push to toggle through presets, press and hold to select. To save a preset after making changes, press and hold. Presets can be toggled and selected using only footswitches (see manual).

Special FX: Reverse makes the delay line go backwards. Jump makes the delay line jump up one octave. Pong (activated with a push and hold) causes echoes to alternate between the left and right channels, meant to be used in stereo.

BREAK RULES AND BUILD WORLDS
Designed to offer a streamlined user experience and a massive feature set, Echolution 3 is a worldbuilder. In a compact package, "E3" offers multi-tap delay lines, with sound design FX options ranging from the subtly cinematic to the outlandishly dramatic. I/O options include stereo output, MIDI sync, and additional footswitch features. On board presets make revisiting your favorite corners of the Echolution 3 universe simple.

HOW TO DISAPPEAR COMPLETELY
Marvin has come across Echolutions in the Pigtronix universe beforeibut never quite like this. Echolution 3 is a supermassive black hole leading to a vivid dimension stuffed with color, light, and the unexplainable, causing the voyager to lose his or herself more deeply than they knew was possible. In this dimension, the imagination tends to expand: familiar figures appear in cloud formations, meteorites can be sat on like bean bag chairs, and ropes of light can be swung on like vines.

MODEL ECHOLUTION 3

MODEL NAME: Echolution 3
SKU: E3
FUNCTION: Stereo Multi-Tap Delay
CATEGORY 1: Delay
CATEGORY 2: Modulation
EXPRESSION: TRS Remote / MIDI
BYPASS: Buffered

ELECTRONICS
VOLTAGE: 9VDC
CURRENT DRAW: 100mA
INPUT IMPEDANCE: High
OUTPUT IMPEDANCE: 1k

BODY
LENGTH (IN): 3.25
WIDTH (IN): 4.5
HEIGHT (IN): 2.2
WEIGHT (LBS): 1

Notes: MG-30 is the flagship modelling effect processor in the NuX range. Dual high speed processing offers accurate modelling of 30 different amplifier options, including bias tweaking for an extra dimension of response adjustment, all using the proprietary NuX TSAC-HD algorithm. Impulse response programming presents a choice of 8 guitar cabinets, 8 bass cabinets, 8 microphones in 3 different axis positions and even 3 acoustic guitar emulation profiles. Once the main guitar tone is programmed, there are 8 effects blocks which can be assigned to different positions in the signal chain, including WAH, CMP, GATE, EFX, EQ, MOD, DLY & RVB. An expression pedal covers wah and swell effects amongst other possibilities. Each has modes and/or parameters which can be adjusted and saved within the patch as needed. Real-time editing uses rotary encoders and switches, making for a natural and organic process and all prameters and graphics are displayed on a vibrant 4" colour display. Add to this a fully functioning USB audio interface, phrase looper, PC/Mac editor/librarian/updater, aux input, effects loop, drum machine and NMP-2 footswitch control and the MG-30 covers practically all bases. This unit provides all the processing power and audio quality that could be asked from any professional guitar processor at a fraction of the price of its component features.

Specifications:

Power supply: 9Vdc, 400mA pin-negative (adaptor included)
Inputs: 6.3mm jack (guitar), 3.5mm jack (aux input)
Outputs: 2 x 6.3mm jack (L/mono + R) to amp or mixer
Sends: returns: 6.3mm jack send (1k ohm) & return (220k ohm)
Headphone output: 3.5mm stereo jack
USB port: USB type-C for audio interface, PC/Mac editing & updating
Remote control connection: EXP1 TRS 6.3mm jack
Sampling format: 48kHz, 32-bit
Frequency response: 20Hz - 20kHz (i1dB)
Input impedance: 1M ohm
Output impedance: 1k ohm
Dynamic range: 110dB
Dimensions: 313 x 166 x 54mm
Weight: 1.5kg

The box for this item contains :

MG-30 multi-effects modeler pedal
1 x 9Vdc power adaptor (UK)
1 x NMP-2 dual footswitch (173.352UK)
1 x patch cable
1 x USB cable

Notes: Like the Iguana that's malleable to its environment, blending into its surroundings for harmonious balance or standing out with vibrant confidence, the Polychrome Flanger is a uniquely colourful tool for adding modulated textures to songs.

The Polychrome Flanger is a true bypass, all analogue Flanger pulling in familiar layout controls from the Julia and Lillian.
Dial in a wealth of colourful flange with the D-F-V blend knob and the shape and voice switches.
The Shape Switch lets you select from sine, triangle, or random LFO wave to modulate the delay line

The Voice Switch lets you select between two voices for the flanging effect.
In the down position, the flanger is more traditional and full frequency.
In the up position, you get a more complex and notched flange effect with less low end.

Like the other members of the Walrus Audio modulation family, the Polychrome has a blend knob. The D-F-V (Dry, Flange, Vibrato) knob lets you blend the dry and delayed signal from full dry at minimum (no effect), to traditional flange at noon to full pitch vibrato at maximum. Don't sleep on the vibrato sounds in the Polychrome.
Set the D-F-V knob to maximum, feedback to a minimum, and the voice switch up for some unique pitch vibrato.

Top mounted input, output, and power jacks as well as soft switch relay bypassing make the Polychrome fit well on your board and ensure smooth operation for years to come.

Specs
The Polychrome comes in a flat black enclosure with purple, yellow, coral, green and white ink, featuring original artwork by David Huttner.
Power supply not included.

Dimensions and power consumption:
0.25kg
6,6 x 12,2 x 5,6 cm (W x D x H)
50 mA

In the box:

Walrus Audio Polychrome
Manual
Sticker
Guitar pick
Pouch

Notes: Dusky drama

Gloamer is an all-analogue, polyphonic amplitude synthesizer that alters the attack and decay time of any sound source without sacrificing the fidelity of the original tone. Its attack function provides a pick-triggered volume swell: a cinematic "slow gear" effect that is smooth and controllable with variable timing from extremely fast to very slow. The volume swell cycle can be reset at any moment by muting, allowing players to craft bowed string-like lines and chords with ease. Gloamer also features a powerful optical compressor that can add subtle punch or extreme sustain, helping to maintain a smooth volume swell effect even with very long attack times. A Volume knob controls loudness at the peak of the attack cycle, while a master Blend control allows players to layer an uncompressed clean sound in with the volume swell effect. Additionally, when activated, the Decay function causes notes to fade out once the attack cycle is complete. When the decay cycle is completed, an auto-reset function causes the attack to begin again immediately, as long as there is audio input. This allows you to create a wide range of undulating, asymmetrical tremolos at slower settings as well as pulsating stutter effects when using faster attack and decay times.

Knob-by-knob

Volume: Sets the master output volume of the effect when engaged.
Compression: Determines the balance of clean and compressed signal.
Blend: Determines the balance of clean signal and effect.
Attack: Determines the duration of time it takes for a note to swell in from silent to full volume.
Decay: Determines the duration of time it takes for a note to fade out from full volume to silence.
Sensitivity: Determines how much input signal is needed to reset the attack and decay cycle.
Ready (LED): Signals when the pedal is armed and ready to begin the attack and/or decay cycle.

A hi-fi attack and decay master
Gloamer was designed to allow players to change the nature of their attack and decay while maintaining pristine, hi-fidelity audio. Easily swell blooming single note lines or full, lush chords and become the string section you've always wanted to hire but can't afford.

Model name: Gloamer
SKU: ATS
Function: Volume Swell with Compressor
Category 1: Modulation
Category 2: Compression

Bypass: True Bypass

Electronics

Voltage: 9VDC
Current draw: 100mA
Input impedance: 470K
Output impedance: 150 ohms

Body:

Length (in): 3.5
Width (in): 4.75
Height (in): 2.5
Weight (lbs): 1

Notes: Cutting Room Floor V3 Pedal

(Vintage Reel-to-Reel Tape, Echo, and Stutter)

The Cutting Room Floor has been updated and now has separate controls over the saturation of the input signal and tape delay signal. With this change, it's possible to have any amount of emulated tape saturation on the input signal and an adjustable tape delay level.

Housed in a smaller, compact footprint, the Cutting Room Floor V3 provides beautifully marred saturated tape tone and ethereal repeats. Imagine an abandoned factory with a fluttering tape machine left on infinite replay.

The Cutting Room Floor was designed to emulate the sound and functionality of vintage reel-to-reel tape overdrive and echo. This pedal reaches into the 21st century with characteristics that traverse the world of modulation and delay. Other features include a freeze button that traps a tone while still playing, and expression/CV control for time.

Designed and assembled in Seattle, Washington. Includes a limited 1-year warranty, if registered within 30 days of purchase.

- 150ma current draw

New in V3:

- Independent control of the tape saturation and tape delay levels

- High-quality knobs with textured grip

- Tape reel design lights up when the pedal is on

- Better layout of the knob placement

- Smaller 125B enclosure (4.77" x 2.6" x 1.39")

Notes: Simply sophisticated

With the 200 series, BOSS introduces a new generation of pedals that pack advanced sound and versatility into a streamlined size that saves space on your board. Grab-and-go controls and multi-function switches make operation easy and intuitive, while onboard memories allow you to store multiple setups for instant recall. All 200 series pedals feature premium audio quality with 32-bit internal processing and offer support for external control via footswitches, an expression pedal, or MIDI.

The OD-200 Hybrid Drive brings next-level sound, feel, and flexibility to overdrive and distortion, combining decades of BOSS tone expertise with innovative technologies. Powered by hybrid analogue/digital circuitry, this dream pedal delivers any drive tone you can imagine via 12 primary modes, 15 boost types, series/parallel gain paths, and more. There's even an advanced gate on board, ideal for both eliminating noise and adding tightness to high-gain drive tones.

Version 1.1 Update: User Memory Expansion

The free Version 1.1 software update brings increased flexibility to the BOSS 200 series, greatly expanding the onboard memory capacity for storing and recalling sounds. There are now 128 user setups available. Setups can also be recalled directly via MIDI program change.

For optimal performance, stay up to date with the current OD-200 system software

Premium Drive Tones with BOSS's Advanced Hybrid Design

The OD-200's next-generation hybrid design seamlessly brings analogue and digital clipping circuits together for the best of all worlds, putting a universe of expressive drive colours under your fingers. Twelve modes offer a variety of premium overdrive, fuzz, and distortion sounds, including a high-gain Brown mode derived from the acclaimed Katana amplifier series. And with the three high-performance "X" drive modes powered by BOSS's cutting-edge MDP tech, you'll experience enhanced definition, clarity, and dynamic response that's perfect for modern playing styles.

Powerful Gain Shaping with Series and Parallel Boosts

While each of the OD-200's 12 main drive modes sound fantastic on their own, you're able to craft tones even further with 15 switchable boost circuits. Placing the boost in series lets you create traditional stacked drive voices, complete with post-gain level to balance with the bypassed sound or kick up the volume for solos. The boost circuit can also be used in parallel with the main mode, enabling side-by-side blending for an unlimited range of unique drive textures.

Kill the Noise and Tighten Your Tone

With its integrated gate circuit, the OD-200 always keeps your signal clear and quiet when you're not playing. The default setting is a great starting point, providing gentle, transparent gating that works well for general playing styles. The decay and threshold controls can also be adjusted for super-fast gate performance when needed, perfect for bringing tightness to heavy modern styles that combine full-throttle gain with precision staccato riffing.

Dial in Sounds Fast

The OD-200 offers a ton of advanced capabilities, but remains as simple to use as any regular distortion stomp. With dedicated controls, you can quickly dial in the gain and overall level for any selected mode, then sculpt the tone with wide-ranging low, mid, and high EQ. There's also a multi-function parameter knob, which changes operation based on the group selected with the panel's parameter switch and LED status indicators.

Save and Recall Your Favourite Setups

The OD-200 features 127 user memories plus a real-time panel setting, giving you 128 total setups to choose from. Any range of consecutive memories and the panel setting can be assigned for scrolling access from a footswitch. It's also possible to limit the scrolling range or assign memories directly for even faster recall.

Specifications

Sampling Frequency: 96 kHz
AD/DA Conversion: 32 bits
Processing: 32-bit floating point
Drive Circuit: Analogue + Digital

Modes:
12 modes
OVERDRIVE, BLUES, SCREAM, CNTR OD, X-DRIVE, DIST, X-DIST, STACK DRIVE, FAT DIST, BROWN, X-METAL, FUZZ

Memory: 127 + Manual
Nominal Input Level: INPUT: -10 dBu
Maximum Input Level: INPUT: +7 dBu
Input Impedance: INPUT: 1 M ohm
Nominal Output Level: OUTPUT: -10 dBu
Maximum Output Level: OUTPUT: +7 dBu (Load Impedance: 220 k ohms or greater)
Output Impedance: OUTPUT: 1 k ohms
Recommended Load Impedance: OUTPUT: 10 k ohms or greater
Bypass: Buffered bypass

Controls: ON/OFF switch, MEMORY/BOOST switch
MODE knob, DRIVE knob, LEVEL knob, PARAM knob, LOW knob, MIDDLE knob, HIGH knob
PARAM button, MEMORY button
Display: 7 segments, 3 characters (LED)
Indicator: PARAM indicator, MEMORY (MAN, 1--4) indicators

Connectors:
INPUT jack, OUTPUT jack: 1/4-inch phone type
CTL 1, 2/EXP jack: 1/4-inch TRS phone type
MIDI (IN, OUT) jacks: Stereo miniature phone type
DC IN jack
USB port: USB micro B-type (program update only)

Power Supply: Alkaline battery (AA, LR6) x 3, AC adaptor (sold separately)
Current Draw: 220 mA

Expected Battery Life Under Continuous Use:
Alkaline: Approx. 6 Hours
* These figures will vary depending on the actual conditions of use.

Accessories:

Leaflet "USING THE UNIT SAFELY"
Leaflet "To obtain the Owner's Manual"
Alkaline battery (AA, LR6) x 3
Rubber foot x 4

Options (sold separately):
AC adaptor: PSA-S series
Footswitch: FS-5U
Dual footswitch: FS-6, FS-7
Expression pedal: FV-500H, FV-500L, EV-30, Roland EV-5
MIDI/TRS connecting cable: BMIDI-5-35, BMIDI-1-35, BMIDI-2-35, BCC-1-3535, BCC-2-3535

Size & weight:

Width: 101 mm / 4 inches
Depth: 138 mm / 5-7/16 inches
Height: 63 mm / 2-1/2 inches
Height: (including rubber foot)65 mm / 2-9/16 inches
Weight: 600 g / 1 lb 6 oz
Weight (including battery): 670 g / 1 lb 8 oz

Notes: This new pedal in Maneco's line is a versatile fuzz device , true stereo and with powerful tone shaping capabilities.

Main features:

True Stereo operation
Silicon Transistors gain stage.
Big Muff tone stack
Buffered clickless Bypass
Input gain for fine tuning distortion quality, also adapting for wide range of input signals
Bass, guitar , drum machines and synthesizer friendly
9v standard power supply, center tip negative

Notes: The perfect companion now comes in a smaller package - introducing Sidekick JR by Crazy Tube Circuits!

Drawing inspiration from the original Sidekick pedal released back in 2019, the aim was to create a compact pedal that combines the most widely used time-based effects, suitable for any gear setup seeking 80s tones and beyond.

From the jangly, ambient, and shimmering sounds of New Wave, Shoegaze, and Synth Pop to the wet tones of Hair / Glam Metal. Crazy Tube Circuits' Sidekick JR offers even more sounds / algorithm selections compared to the original unit.

The modulation effects / algorithms take inspiration from classic 80s stompboxes. The "Ensemble" algorithm replicates warm and mild modulated chorus sounds, while the "dimension" algorithm enhances the 3D image of your sound without the typical chorus warble. The "flanger" algorithm draws from a classic flanger pedal set up as a slow chorus with mild feedback added for a more metallic sound.

The Echo / delay section provides the sweet and vibrant sound of a tape echo with a freshly installed tape running through a colourful preamp, or the pristine repeats of an 80s digital delay rack unit.

The Reverb section in Sidekick JR is inspired by definitive examples of 80s reverb rack units and offers two algorithm banks. Bank A includes all-time classic reverb sounds like "plate," "spring," and "hall," while Bank B features signature 80s reverb sounds like "gated," "exciter" (Crazy Tube Circuits' trademark big-hall reverb algorithm with almost infinite reflections and decay), and octave-up "shimmer."

To provide full flexibility in the smallest enclosure possible, Crazy Tube Circuits has devised a smart switching setup. The delay and reverb effect sections of Sidekick JR operate independently from each other, and the modulation is assignable to any of these sections as standard. With the addition of the XT footswitch (available separately), the modulation section becomes entirely independent and can be switched on/off (true bypass) on its own.
Crazy Tube Circuits' Sidekick JR also features a power-up bypass/engage pre-set function for the onboard footswitches. This feature allows users to select the state the pedal will go to when the power supply is plugged in. It's particularly useful for individuals who use remote pedal switchers /loopers, as they can set the power-up state of the pedal once and then operate it from the controller.

Notes: DigiTech announces SDRUM Strummable Drums, the first-ever intelligent drum machine for guitarists and bassists. Boasting studio-quality samples and five professional sounding drum kits and BeatScratch technology, SDRUM allows users to create drum patterns by simply strumming strings.

As a player scratches across guitar or bass strings, he or she "teaches" SDRUM a kick/snare pattern that defines a desired beat. Once that pattern is established, SDRUM then enhances and enriches the beat, resulting in a realistic accompanying drum part. From the five different kits, users are able to choose sounds appropriate to a broad variety of musical styles. Via the KICK and SNARE Pads, players can audition the various kits and tap in specific beats, while the GUITAR AUDITION Button enables the user to turn the drum output on or off while strumming.

Up to 36 songs can be stored in SDRUM, and the unit supports three different components - e.g. verse, chorus, bridge - for each that can be switched on in real-time to easily facilitate live performance and aid in composition and creativity. Additionally, JamSync functionality facilitates compatibility with JamMan loopers, further boosting SDRUM's capacity in concert, practice, and studio settings.

The compact SDRUM (5.25" x 3.15" x 2.3") is similar in size to most compact effects units and fits easily on standard pedalboards. A sturdy metal chassis, robust footswitch, and four knobs (GROOVE/KIT, LEVEL, TEMPO, and HAT/RIDES) ensure that SDRUM is stage- and road-ready.

Eliminating the need to sift through libraries of rhythm patterns in search of an appropriate match for individual songs and styles, SDRUM is the fastest way to go from a beat idea to a working drum track.

BeatScratch Technology
JamSync Support
Studio-quality samples
Five drum kits
Verse/Chorus/Bridge parts
Alternate instruments/voicings
External FS3X support
Kick/Snare pads
Controls: Tap Tempo, Verse/, Chorus, Bridge, Song, Groove/Kit, Hats/Rides, Level, Temp, Alt Kit, Alt Hats/Rides, Guitar Audition, Kick Snare, Footswitch
5.25" (L) x 3.15"(W) x 2.3" (H)/ 133mm (L) x 80mm (W) x 58mm (H)
1.12 lb./.51 kg
Power Supply (external - included): PS0913DC-04 (US, JA, EU, AU, UK)
Warranty: 1 Year

Notes: Inspired by the vintage Bell and Howell 385 Filmosound projector that guitarists have modified and used as guitar amps, Walrus has created a dynamic and responsive overdrive modeled after the projector's tone.

The 385 was developed to have the same simple but effective tone control as it's older relative, but unlike the projector, the 385 breaks up the single tone control and integrates separate, boost and cut bass and treble, allowing the player to get more creative with mid-frequency scoops and bumps allowing for a much wider array of tones to be achieved.

The pedal is internally running at 18v, which helps us nail the same dynamic feel of the amp in a stomp box.

This means it is extremely sensitive to how hard you dig in - just like the amp.

Updated for 2023.

Controls:

Bypass: Soft touch, relay true-bypass. Press the switch to engage/disengage the pedal. LED indicates whether the circuit is engaged or not.
A/B: Soft touch switch. Press to swap between using either A (White) or B (Red) Volume and Gain controls. LED indicates which controls are being used - White for A, Red for B.
Volume A: Controls the overall volume in the A setting. Turn clockwise for more volume, counter-clockwise for less volume.
Gain A: Controls the overall gain in the A setting. Turn clockwise for more gain, counterclockwise for less gain.
Volume B: Controls the overall volume in the B setting. Turn clockwise for more volume, counter-clockwise for less volume.
Gain B: Controls the overall gain in the B setting. Turn clockwise for more gain, counterclockwise for less gain.
Treble: Used to adjust the level of the treble frequencies. Turn clockwise to increase the level of the treble frequencies. Turn counter-clockwise to reduce the level of the treble frequencies.
Bass: Used to adjust the level of the bass frequencies. Turn clockwise to increase the level of the bass frequencies. Turn counter-clockwise to reduce the level of the bass frequencies.
385+ Switch: When the switch is down, you are able to achieve classic 385 sounds. Flip the switch up to add an additional gain stage to the input of the pedal, achieving heavier gain sounds and driving the pedal harder.

Specifications

The 385 comes in a matte black finish with yellow and red ink featuring original artwork of a vintage Belle and Howell 385 projector by David Huttner ready to give you the dynamic tone you've been searching for.
The die cast enclosure's exact size is 12.1 x 6.6 x 3.5 cm
Power requirements are 9VDC (100mA minimum). The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
Daisy chain power supplies are not recommended. Power supply not included.
Input: 1/4" TS, Unbalanced, 1M impedance
Output: 1/4" TS, Unbalanced, 10k impedance
True Bypass

Notes: How It Works

Chaining up an EQ, compressor and overdrive pedal will never give you the same result as SkarBassOne achieves, not by a long shot! The precise filters in SkarBassOne is what gives you the extremely surgical tone and the wide range of possibilities without breaking a sweat!

No matter the settings you will always keep the clean powerful low end with this multiband overdrive and that is a must for bass. Controlling the mids of a bass sound has never been easier! You will get out of the way from other instruments masking frequencies and take up all the space that is ment for you and ONLY you!

It might look simple on the outside, but I assure you the inside is a matrix of years with development. The flexible multiband drive is smooth all the way thru it's range and I promise you it will never ever mess with your low end!

Details

Compression:

One knob FET compressor with fast attack and release. It handles dynamics with ease and creates a solid wall of tone.

Compression LED:

Visual indication of how hard the compressor is working.

Mid:

Mid filter to achieve the surgical studio tone! Create a defined, in the pocket frequency response for the bass to sound massive and to make it sit with other instruments. Your band mates will never beg you to turn down your bass again!

Mix:

Quickly set the tonal balance between low frequencies and high frequencies. Find the sweet spot in any situation.

Footswitch:

On/Off switch for Drive and Tone.
Red channel =Drive and Tone active.
Blue channel = Drive and Tone off.
Compression, Mid and Mix is active on both channels.

Drive:

Set the amount of multiband drive, from gentle push to full on bark!

Tone:

Hi-cut filter to control the high frequencies of the output.

Notes: Part of the new Boss 200 series, the RV-200 is a seriously classy reverb. With a choice of 12 algorithms, things quickly move from classic ambience to the pitch-shifted arpeggiated madness of the new Arpverb program.

Supplier's Notes:
Ambient Bliss

The RV-200 delivers inspiring reverbs and premium sound in the streamlined BOSS 200 series design. Twelve versatile reverb types-including the newly developed Arpverb-provide everything from subtle spatial colour to complex, dreamy textures for ambient explorations. Quickly dial in sounds with the fast-access interface. Save favourites in 127 memories. And take performances to the next level with flexible onboard footswitches, deep external control support, and head-turning creative tools like Warp, Twist, and more.

Studio-Grade Processing

The RV-200 features a powerful reverberation engine with class-leading sound quality, backed by custom BOSS DSP, 32-bit AD/DA, 32-bit floating point processing, and a 96 kHz sampling rate. Every algorithm offers true studio-grade performance, with exceptional detail and definition from the shortest early reflections to long, floating tails spanning multiple seconds.

Twelve Distinctive Reverbs

From essentials like Room and Hall to deeply immersive reverbs like Shimmer, Slowverb, and the cool new Arpverb, the RV-200 gives you the ambient colours you need for every song and style.

Room

Simulates the reverberation characteristics of a small room. Select from four room sizes with the Param knob.

Hall

Simulates the reverberation characteristics of a concert hall. Select from three hall sizes with the Param knob.

Plate

Simulates the reverberation characteristics of a studio plate reverb. Balance the high and low damping of the reverb with the Param knob.

Spring

Simulates the distinctive sound of the hardware spring reverb effect found in guitar amplifiers. Select the number of springs with the Param knob.

Shimmer

Creates long, dreamlike reverberations rich in harmonic content. Adjust the harmonic character and diffusion with the Param knob.

Arpverb

A newly developed BOSS reverb that creates an arpeggio type of sound with evocative pitch-shifted tails. Use the Param knob to adjust the attack of the arpeggio sound.

Slowverb

A sweet ambient reverb with gentle attack and soft harmonics. Param adjusts the amount of direct sound blended with the reverb, allowing you to create deep, immersive tones.

Modulate

Adds a modulation effect to a rich hall reverb sound. Adjust the modulation depth with the Param knob.

+Delay

Combines a delay with reverb, with the length of both effects controlled with the Time knob. Use the Param knob to adjust the delay level.

Lo-Fi

A specialty reverb with limited bandwidth and added distortion. Adjust the distortion amount with the Param knob.

Gate

A distinctive reverb effect that abruptly cuts off the reverb tail. Use the Param knob to control the timing of the gate effect.

Reverse

Plays the reverb sound in reverse. Adjust the high-frequency character with the Param knob.

Instant Sound Creation

Like all 200 series pedals, the RV-200 offers a powerful yet intuitive panel that lets you realize great sounds with minimal effort. Along with core parameters such as reverb time, effect level, and pre-delay, there are variable high and low filters to perfectly balance the verb for your application. You also have a density control to adjust the weight of the sound, plus a parameter knob with access to multiple sound-shaping tools that are unique to each type.

Expressive Performance Control

The RV-200 includes memories for storing 127 reverb sounds, so your favourite setups are always ready to go. Two onboard footswitches pack a lot of performance versatility, with numerous options to reassign their targets to suit your needs. For example, you can bypass the effect, scroll through memories, and activate a Hold function to carry on the reverb effect for as long as the switch is pressed. It's also possible to assign powerful performance effects such as Warp, Twist, and Fade.

Specifications

Sampling Frequency: 96 kHz
AD/DA Conversion: 32 bits
Processing: 32-bit floating point
Modes: 12 modes- ROOM, HALL, PLATE, SPRING, SHIMMER, ARPVERB, SLOWVERB, MODULATE, +DELAY, LO-FI ,GATE, REVERSE
Memory127 + Manual
Nominal Input Level: INPUT A/MONO, B: -10 dBu
Maximum Input Level: INPUT A/MONO, B: +7 dBu
Input Impedance: INPUT A/MONO, B: 2 M ohms
Nominal Output Level: OUTPUT A/MONO, B: -10 dBu
Maximum Output Level: OUTPUT A/MONO, B: +7 dBu
Output Impedance: OUTPUT A/MONO, B: 1 k ohm
Recommended Load Impedance: OUTPUT A/MONO, B: 10 k ohms or greater
Bypass: Buffered bypass
Controls: ON/OFF switch, MEMORY/HOLD switch, MODE knob, TIME knob, PRE-DELAY knob, E. LEVEL knob, PARAM knob, LOW knob, HIGH knob, DENSITY button, MEMORY button
Display: 7 segments, 3 characters (LED)
Indicator: DENSITY indicator, MEMORY (MAN, 1--4) indicators

Connectors
INPUT (A/MONO, B) jacks, OUTPUT (A/MONO, B) jacks: 1/4-inch phone type, CTL 1, 2/EXP jack: 1/4-inch TRS phone type, MIDI (IN, OUT) jacks: Stereo miniature phone type, DC IN jack, USB port: USB2.0 micro B (program update only)
Power Supply: Alkaline battery (AA, LR6) x 3, AC adapter (sold separately)
Current Draw: 260 mA

Expected Battery Life Under Continuous Use: Alkaline: Approx. 4 Hours
* These figures will vary depending on the actual conditions of use.
Accessories: Leaflet "USING THE UNIT SAFELY", Leaflet "To obtain the Owner's Manual", Alkaline battery (AA, LR6) x 3, Rubber foot x 4

Options (sold separately):
AC adaptor: PSA-S series
Footswitch: FS-5U
Dual footswitch: FS-6, FS-7
Expression pedal: FV-500H, FV-500L, EV-30, Roland EV-5
TRS/MIDI connecting cable: BMIDI-5-35, BMIDI-1-35, BMIDI-2-35, BCC-1-3535, BCC-2-3535

Size & weight

Width: 101 mm / 4 inches
Depth: 138 mm / 5-7/16 inches
Height: 63 mm / 2-1/2 inches
Height(including rubber feet): 65 mm / 2-9/16 inches
Weight: 610 g / 1 lb 6 oz
Weight (including battery): 680 g / 1 lb 8 oz

Notes: Dial in Professional Sounds in Seconds

The BOSS ME series has been a favourite of performing guitarists for over three decades, combining multi-effects power with intuitive hands-on control for crafting tones in seconds. The ME-90 is the most advanced ME model to date, offering exceptional audio quality, flagship-grade AIRD amp models, IR loading, an effects loop, and more. Compact, battery-powered, and filled with premium BOSS tones, this versatile all-in-one processor makes it easy to build customized sound setups for every playing situation.

Fast Sound Creation

With its knob-driven interface and diverse effects selection, the ME-90 lets you build configurations and tweak tones with the ease of a stompbox-filled pedalboard-without the hassle of fastening tape, power distribution, and multiple connection cables. Just dial up an amp model or effect type within a category and turn the knobs to get the sound you want. There are 36 preset patches with ready-to-play pro tones, plus 36 user patches for storing your custom creations.

Flexible Real-Time Control

The ME-90 features eight footswitches with smooth, quiet operation and an expression pedal with an integrated toe switch. Use Memory mode to call up complete patch setups with the footswitches, and then switch to Manual mode for direct on/off control of each effect category within the patch. The footswitch LEDs light in different colours for quick identification in the heat of a performance. It's also possible to set all LEDs to light in a fixed colour for each mode if desired.

High-Quality BOSS Effects

The ME-90 puts a massive library of BOSS effects at your command, offering seven different categories filled with selections derived from the flagship GT-1000. Everything you need is here, from overdrives and distortions to pitch/mod effects, delays, and high-quality reverbs. You also get 11 dedicated Pedal FX, a looper, and specialized effects such as acoustic simulation and down tuning. There are 60 effect types in total, with access to over 20 more via BOSS Tone Studio. A send/return loop is available for external pedals, complete with the ability to save the on/off status in patches and place the loop before or after amp models in the signal chain.

Premium Amp Sounds with AIRD Technology

Along with its effects, the ME-90 includes amp models ported from the GT-1000, driven by our advanced AIRD technology for authentic tube tone and touch response. Eleven onboard amp types offer everything from clean combo sounds to punishing high-gain stacks, and you can access more selections in BOSS Tone Studio. Each amp includes a dedicated cab sound for connecting to a PA or recording device, and you can load three of your favourite speaker IRs to personalize sounds to your taste.

Edit, Customize, and Expand

BOSS Tone Studio for macOS and Windows extends your creative range, allowing you to edit tones and change out some amp and effect types with alternate selections. In addition, you can save and organize patches for different gigs, download pro setups at BOSS Tone Central, and swap patches with the ME-90 community on BOSS Tone Exchange. The ME-90 also supports the optional Bluetoothr Audio MIDI Dual Adaptor, enabling you to stream music from a mobile device and wirelessly shape tones using the dedicated BTS editor app for iOS and Android.

Light, Durable, and Ready to Travel

The ME-90 is lighter than its previous generation model while maintaining the rock-solid durability that BOSS is famous for.

Specifications
Sampling Frequency: 48 kHz
AD Conversion: 24 bits + AF method
AF method (Adaptive Focus method) This is a proprietary method from Roland & BOSS that vastly improves the signal-to-noise (SN) ratio of the AD and DA converters.
DA Conversion: 32 bits
Processing: 32-bit floating point
Effects: 97 Types
Memories: 36 (User) + 36 (Preset)
Phrase Loop: 38 sec. (MONO)
Tuner Internal Detection: +/-0.1 cent
Nominal Input Level: INPUT: -10 dBu, RETURN: -10 dBu
Maximum Input Level: INPUT: +7 dBu, RETURN: +7 dBu
Input Impedance: INPUT: 1 M ohm, RETURN: 1 M ohm
Nominal Output Level: OUTPUT (L/MONO, R): -10 dBu, PHONES: -10 dBu, SEND: -10 dBu
Output Impedance: OUTPUT (L/MONO, R): 1 k ohm, PHONES: 44 ohms, SEND: 1 k ohm
Recommended Load Impedance: OUTPUT (L/MONO, R): 10 k ohms or greater, PHONES: 44 ohms or greater, SEND: 10 k ohms or greater

Controls:BANK DOWN/AMP switch, BANK UP/EQ switch, CTL/REV switch, MEMORY/MANUAL switch, 1/COMP switch, 2/OD/DS switch, 3/MOD switch, 4/DELAY switch, PEDAL FX switch, Gt. AMP/LINE switch, POWER switch, EXIT button, WRITE button, CTL button, EDIT button, PREAMP TYPE knob, GAIN knob, BASS knob, MIDDLE knob, TREBLE knob, LEVEL knob, REVERB knob, COMP/FX1 TYPE knob, SUSTAIN/SENS/-1OCT knob, ATTACK/TONE/-2OCT/DEPTH knob, LEVEL/PEAK/DIRECT knob, OD/DS TYPE knob, DRIVE knob, TONE knob, LEVEL knob, MOD TYPE knob, RATE/KEY knob, DEPTH/HARMONY knob, E.LEVEL/RESONANCE knob, DELAY TYPE knob, TIME knob, FEEDBACK knob, E.LEVEL knob, OUTPUT LEVEL knob, PEDAL FX TYPE knob, PEDAL FX pedal
Display: 7 segments, 2 characters (LED)

Connectors: INPUT jack, OUTPUT (L/MONO, R) jacks, SEND jack, RETURN jack: 1/4-inch phone type
PHONES jack: Stereo miniature phone type
USB COMPUTER port: USB Type-C(R)
Bluetooth ADAPTOR connector: Dedicated connector
DC IN jack

Power Supply: Alkaline battery (AA, LR6) x 4 or AC adapter
Current Draw: 190 mA

Expected battery life under continuous use:
Alkaline battery: Approximately 6.5 hours
* This can vary depending on the specifications of the batteries, capacity of the batteries, and the conditions of use.
Accessories: STARTUP GUIDE, Alkaline battery (AA, LR6) x 4, Leaflet "USING THE UNIT SAFELY"

Options (sold separately)
AC adaptor: PSA-S series
Bluetooth(R) Audio MIDI Dual Adaptor: BT-DUAL
Carry Bag: CB-ME80,CB-BU10

Size & weight

Width: 443 mm / 17-1/2 inches
Depth: 220 mm / 8-11/16 inches
Height: 67 mm / 2-11/16 inches
Maximum Height: 93 mm / 3-11/16 inches
Weight(including battery): 2.9 kg / 6 lb / 7 oz

Notes: A reverb processing powerhouse!

The EHX Oceans 12 is the Oceans 11's big brother with even more reverbs and functionality. It features two simultaneous, independent, stereo reverb engines, series and parallel control for the dual reverbs, 24 presets and advanced I/O allowing for stereo in/out or mono send/return with pre and post reverb options. The pedal also includes a new Tide Control for stereo image alteration, a Lo-fi Control, an infinite attenuation control and an input jack for external expression and 3-button footswitch control.

A Tails switch provides a choice of whether the reverb effect fades out naturally or stops immediately when the pedal is switched to bypass. In most settings the pedal is also capable of producing infinite reverb which can be played over with a different reverb effect.

The Oceans 12's reverbs are:
• ROOM - two modes: reverb algorithms modeled after a lively room and a spacious performance hall
• SPRING - two modes: vintage 1962 Fenderr 6G15 tube reverb emulation and the spring algorithm from the EHX Holy Grail
• PLATE - two modes: two emulations of the smooth, metal plate reverb often used in high-end recording studios during the 1960s and '70s
• REVERSE - two modes: a reverse reverb effect as well as true reversed echoes
• ECHO - three modes: a digital delay with various echo rhythms feeding into a plate reverb
• TREM - three modes: a classic, periodic volume envelope with various shapes applied to both the wet and dry mix of a hall reverb
• MOD - three modes: combinations of chorus and flange reverbs that create rich reverb tails
• DYNA - three dynamic, experimental reverb algorithms: swell, gate and duck
• AUTO-INF - three modes: auto-infinite reverb (w/optional chorus or flange) that "listens" to your playing and crossfades to a new reverb wash upon detection of newly struck notes.
• SHIMMER - two modes: two configurations of a rich octave-shifted reverb wash
• POLYPHONIC - two modes: two configurable bi-directional pitch shifts that add dimensionality to the reverb tail
• RESONANT - two modes: reverb excited by tunable resonators and configurable self-oscillating filters on the reverb tail

2 simultaneous, independent, stereo reverb engines
Series and parallel control for the dual reverbs
24 presets
Stereo in/out or mono send/return with pre and post reverb options
Tide Control for stereo image alteration
Lo-fi Control
Infinite attenuation control
Tap tempo to set your pre-delay time, echo time and more
Input jack for external expression and 3-button footswitch control
Power supply included

SPECIFICATIONS
Circuit
Digital
Bypass
Buffered Bypass
Audio
Stereo
Effects Loop
Yes
Power Supply
9.6VDC-200mA power adapter included
Dimensions (in)
4.75 x 3.9 x 2.5
Current Draw
150mA
Year Released
2020

Notes: The Wash is a dream come true for ambient player and ushers in a new chapter in the world of delays. It accomplishes the arduous task of creating an organic, below-the-mix wash. Normally this requires stacking 3-4 reverb and delay pedals at the end of your chain. The unique "Wash Circuit" creates the perfect wash with only one pedal.

For the new version (V2), Hungry Robots worked hard to squeeze the circuit into a smaller enclosure while keeping the build quality and tone quality identical. The circuit that hundreds of users have fell in love with is unchanged. The new versions are 2 inches smaller left and right. In addition to the smaller enclosure, the new option for top mounted jacks can save you a lot of board space.

At its most basic utility, The Wash is an outstanding analog-voiced, tap-tempo delay with just over 1000ms of delay time.

The Wash circuit is what makes the pedal stand out from other delays on the market. The Wash circuit adds reverb to the signal and through a complicated network of internal feedback loops, subtle multi-head Binson effect, and what is known as "ripple effect," It works to add a hauntingly beautiful wash to your signal in ways that can't be accomplished by stacking a reverb and a delay in series. It does all of this while keeping the clarity and presence of your original signal without getting lost in the soup of decay.

The Wash reacts to your playing unlike the common DSP reverb/delays with an infinate sustain function. There is a dynamic quality to it that is hard to replicate with any other single pedal.

The "Ripple" knob controls The Ripple Effect. The Ripple Effect is a feature in which each successive delay trail slowly scatters and transforms into reverb. The "Resonance" knob is to fine-tune the resonance and decay of the wash. The Middle "The Wash" knob controls the mix/level of the wash.

Current Draw: 92-93 mA

Switching: True-Bypass

Dimensions: 4.7" x 3.7" x 1.96"

Powering: 9V DC - Negative Center - 2.1mm Barrel