New releases last four weeks: All genres

Notes: Space-conscious lowpass filter and volume processor.

A combination of VCF + VCA + Mixer that lets you mix three different sound sources, and shape their tone, and levels in a breeze.

The Pony Filter is built around the SSI2144 FATKEYS Chip. Has the elegant sound of the classic transistor filter without the associated distortions, due to Dave Rossum's "improved ladder" topology.

Features

3 Channel Mixer (Out normalized to channel three for feedback)
Temperature-compensated Q and frequency.
Compensated Volume VS Resonance
2 Cuttof CV INs.
CV 1 Selectable routing Cut-Off or Cut-Off+VCA
Voltage controlled Q
Two Segment Peak Meter

Specifications

Four-pole, 24 dB/octave
Current needs: +12V=50mA, -12V=45mA
Width: 6 HP
Depth Assembled Version: 22mm
Depth DIY Kit Version: 40mm
Designed, kits prepared and assembled in Barcelona.

Notes: Lush analogue EQ switchable between tilt and Baxandall high-shelf configurations.

Perform a variety of mixing and sound design duties ranging from subtle brightness and clarity adjustments to low-end rumble removal, boosted low-pass filtering and sweep EQ.

In the default tilt mode, turning the control knob clockwise simultaneously boosts treble and cuts bass. Turning anti-clockwise boosts bass and cuts treble. These boosts and cuts are pivoted around the mid-range. With the control knob at 12 o'clock the frequency response is neutral.

With Baxandall high-shelf mode enabled, turning the control knob clockwise past 12 o'clock introduces and gentle high-shelf EQ weighted around the upper mid-range. Turning the control knob anti-clockwise results in a wide high-shelf cut with subtle bass and mid-range adjustments.

Patching the channels in series allows for radical sound shaping and band-pass responses. Each channel provides up to +/- 8db of low and high-frequency gain control, summing into a low noise output stage. Hot input signals over 15vpp are saturated by active Zener diode clipping.

Features

Precise voltage control of EQ tilt and shelf
Seamless switching between EQ modes
High-quality components used throughout

Specifications

Intellijel 1U format
Width: 18HP
Depth: 32mm
Power requirements: ~60mA +12V/~58mA -12V
Control voltage range: 0-8V
Impedance Input: 100K / Output 1K

Notes: Lush analogue EQ switchable between tilt and Baxandall high-shelf configurations.

Perform a variety of mixing and sound design duties ranging from subtle brightness and clarity adjustments to low-end rumble removal, boosted low-pass filtering and sweep EQ.

In the default tilt mode, turning the control knob clockwise simultaneously boosts treble and cuts bass. Turning anti-clockwise boosts bass and cuts treble. These boosts and cuts are pivoted around the mid-range. With the control knob at 12 o'clock the frequency response is neutral.

With Baxandall high-shelf mode enabled, turning the control knob clockwise past 12 o'clock introduces and gentle high-shelf EQ weighted around the upper mid-range. Turning the control knob anti-clockwise results in a wide high-shelf cut with subtle bass and mid-range adjustments.

Patching the channels in series allows for radical sound shaping and band-pass responses. Each channel provides up to +/- 8db of low and high-frequency gain control, summing into a low noise output stage. Hot input signals over 15vpp are saturated by active Zener diode clipping.

Features

Precise voltage control of EQ tilt and shelf
Seamless switching between EQ modes
High-quality components used throughout

Specifications

Intellijel 1U format
Width 18HP
Depth 32mm
Power requirements ~60mA +12V/~58mA -12V
Control voltage range 0-8V
Impedance Input 100K / Output 1K

Notes: CV Random is a random CV generator with 4 types of randomness and a triggerable sample-and-hold function.

Sliders allow you to set the internal clock tempo (RATE), shape the probability of triggering (PROB), blend old with new values (RND) and set the shape of all four random outputs (SHAPE).

4 different sliders

RATE

Sets the tempo of the internal clock. The CV input below the slider adjusts the clock rate, with 1V/oct calibration when the CV attenuverter is 100%. Upon each clock trigger, the RATE slider light blinks, and there is a chance for the internal random source to generate a new value.

PROB

This probability is set by the PROB slider, and if a new value was generated, the PROB slider light blinks and a pulse is emitted from the TRIG output.

RND

When the internal random source generates a new value, it mixes the previous value with a random value, with an amount specified by the RND slider.

SHAPE

The SHAPE slider sets the shape of all four random outputs. At its lowest position (0%), all outputs immediately jump to the new random value (the target value) when the clock is triggered.

At non-zero positions, the outputs interpolate between the previous and the target value, using a different behaviour for each output.

Internal random clock source

Whenever the clock activates, the RATE slider's light flashes. At the same time, there's a chance that the internal random source will create a new value, depending on the PROB slider's setting.

If it does create a new value, the PROB slider's light flashes too, and a pulse comes out of the TRIG output.

External IN & TRIG inputs

If the TRIG input is patched, the RATE slider is ignored, and the internal clock is only triggered when an external trigger is received. The PROB slider is used to filter this trigger by applying some probability.

Self-modulation

Thanks to a switch in the back of the module, you can normalize the LIN output to the 4 CV inputs and adjust the amount of modulation for each parameter with the attenuverters.

This adds another layer of randomness to your results, enabling more dynamic and unpredictable outcomes.

SHAPE Outputs

The STEP output jumps to the new value in one step at 0% SHAPE, and divides the transition into 16 steps at 100% SHAPE.

The LIN output immediately reaches the new value at 0% SHAPE, and takes the whole clock cycle to do so at 100% SHAPE, staying constant in between.

The EXP output shifts exponentially, becoming linear at 100% SHAPE, with its pace adjusted by the SHAPE slider.

The SMTH output transitions smoothly, with the speed controlled by the SHAPE setting, holding at the target until the cycle ends.

Specifications

Dimensions 10HP - 50×128,5mm
Current 63 mA +12V / 11 mA -12V / 0 mA +5V
Input & Output Signals +/-10V
Impedance Input 10k - Output 10k
Materials PCB and Panel - FR4 1,6mm
Depth 40mm including connectors (Skiff friendly)

Notes: Zeus Guitar Pedal Power Supply

NU-X have built an enviable reputation as guitar pedal experts and great guitar sound starts with the power source. Using standard 9Vdc power adaptors usually releases unwanted noise into the signal chain and unstable power can adversely affect the operation and even life expectancy of some boutique pedals. Zeus is an extremely low noise, high current power supply designed specifically for audio effect circuits with 6 fully isolated 9V outlets, 3 switchable 9/12/18V outlets and a fully variable 6-12V outlet. This lightweight and efficient power supply has the flexibility and reliability to run a full pedal board, even with multi-effect units added, with problem-free operation.

Extremely low noise circuitry
Fully isolated outputs
Multiple voltage options
High current capacity
Supplied with various DC link cables to havndle most pedal input types
Supplied with a 2-outlet combiner lead with 2.5mm DC plug for higher power units.

Power supply: 100-240Vac, 50/60Hz (IEC)
Outputs: 6 x 9VDC, 3 x 9/12/18vDC, 1 x 6-12Vdc variable (all DC5521 jack)
USB output current: 1.5A (Type-A outlet)
Dimensions: 195 x 101 x 42mm
Weight: 658g

In the box

The box for this item contains :

Zeus guitar pedal power supply
5 x DC jack link cables (5.5x2.1mm) straight to angle 0.5m
5 x DC jack link cables (5.5x2.1mm) straight to angle 0.3m
1 x DC jack reverse polarity cable (5.5x2.1mm) straight to angle 0.5m
1 x DC jack (5.5x2.1mm) to 3.5mm plug cable 0.5m
1 x twin DC jack (5.5x2.1mm) socket to single DC plug (5.5x2.5mm)
1 x IEC power lead