Coming soon: Studio Equipment

Notes: Following ADDAC's ADDC503 Marble Physics here is a new simulation of a physical system. This time, imagine a small area in the middle of the ocean, in this area we place 4 equally spaced buoys anchored to the bottom in such a system that we can control the spacing between the buoys. Imagine we can control the elements and agitate the waters at will which in turn will make the buoys move up and down as the water surface moves.

Finally imagine the buoys would wirelessly transmit their absolute height directly to your module outputs where they would be mapped to a voltage signal.

ADDAC use a Gerstner Wave as the motor behind the two-dimensional wave generation. In fluid dynamics a Gerstner Wave is described as "a progressive wave of permanent form on the surface of an incompressible fluid of infinite depth". Gerstner waves are often used in computer graphics to simulate any type of water surface, if you've seen any animation film or computer game with water surfaces in it most probably it features a Gerstner wave generating it.

Tech Specs:

10HP
4.5cm deep

70mA +12V
40mA -12V

Notes: Alter 2 is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 2. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and filter as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects.
(note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y.)
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and filter all have CV control inputs.
- Each control level or cv input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input.
- Mono input is made stereo within the DSP and outputs to both left and right channels.
- Stereo outputs for right and left channels.

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 2 are as follows:
1 - Analogue delay
2 - Reverb with infinite capture and LP + HP filters
3 - Choral reverb
4 - Palindrome reverse delay - backward/forward repeat
5 - Time stretch
6 - Pitch shift (notated semi-tones)
7 - Time stretch glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: Alter is an effects processor for Eurorack format. There are two versions of the Alter which are visually identical except the names "Alter 1" and "Alter 2". This is Alter 1. Internally, 1 & 2 have an entirely different set of effects from the other. Each version features 7 unique and meticulously designed DSP effects.

Control

- Controls for mix, X, Y and Sift as well as clock.
- All effects have a variation of a filter which may change effect to effect.
- X and Y control various rates, feedback and time over the different effects (note that some of the images shows a prototype which says "rate" under two of the pots. The faceplate has been changed to X and Y).
- Clock control adjusts the rate which controls the DSP which can drastically change the effect. In doing so it does slightly lower the quality of the output signal but the results are fantastic. This clock is not for synchronization.
- Mix, X, Y and Sift all have CV control inputs.
- Each control level or CV input is visualized on the control panel.

Ins and outs

- Stereo inputs with separate level/gain control for right and left channels. These levels can also act as mute as it can take the signal to 0. They can also add gain to a quiet signal.
- Peak level indicator for clipping levels at the input
- Mono input is made stereo within the DSP and outputs to both left and right channels
- Stereo outputs for right and left channels

Effects

The effect is selected by the hexagonal touch pad. The effects for Alter 1 are as follows:
1 - long delay
2 - tight, notated granular delay
3 - plate reverb
4 - shimmering reverb
5 - distortion multi-filter
6 - pitch delay
7 - stutter glitch

Specs

Includes printed manual
+12V: 160mA
-12V: 0mA
+5V: 0mA
16HP width
25 mm Depth

Notes: The CubuSynth Engine V2 is their updated dual analogue VCO with wave shaping functions, internal modulations and a chaos generator. It is based around the 3340 chip and features 4 Waveforms + Wavefolder per VCO and 4 Modulated Outputs, all simultaneously.

The CubuSynth Engine can work as 2 independent VCOs, or as one complex FM oscillator.

With its internal "Chaos Engine" it creates semi-random voltages, generated by the 2 oscillator cores. This signal is then normalized to the CV inputs for Pulse width modulation and exponential FM.

Each of the 2 VCOs offers a switch to select one of the 4 waveshapes to be used by the wavefolders, and the linear FM input normalisations.

Features:

2 VCO cores (voices)
4 simultaneous wave forms per voice + 4 Modulation Outputs
Wavefolder per voice
Pulse Width modulation
Linear and exponential FM inputs
1 V/oct tracking stable over up to 10 octaves
Chaos generator with external clock input
Complex internal normalized modulations

Dimensions:
24 HP
24 mm deep

Current Draw:
87 mA +12V
74 mA -12V
15 mA 5V