100% Compra Segura

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Compra Segura

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Coming Soon: Studio Equipment

Inicio  Coming Soon  

Studio Equipment

Options
Artículos del 1 al 24 de 24 en la página 1 de 1
FORTHCOMING
Wavefonix 3340 Voltage Controlled Oscillator Module
Cat: 796464 Rel: 14 Dec 20
 
Voltage controlled oscillator module
Notes: Featuring the legendary CEM3340 IC, the 3340 Voltage-Controlled Oscillator (VCO) module offers that classic, rich analog sound found in many famous synthesizers from the past, along with a wide range of sound shaping and modulation possibilities.

Specifications

Format: Eurorack
Width: 13hp
Depth: approx. 40mm
Power consumption:
+12V: 60mA
-12V: 50mA
+5V: 0mA
Read more
coming soon $190.94
FORTHCOMING
Tesseract Modular Sweet Sixteen Mk2 Module
Tesseract Modular Sweet Sixteen Mk2 Module (attenuater / controller / MIDI synth module)
Cat: 797258 Rel: 31 Jan 21
 
Synth module
Notes: This module is a eurorack version of the 16n Faderbank, implemented with 16 CV inputs and some other smart add ons. Almost everything is in the front panel.

This new version is oriented for firmware tweaks and future expansions, still being fully compatible with the 16n and the previous Sweet Sixteen.

Changes from previous versions:

Function push button
Function led
Expansion header in the back
i2C pull-up switchable with jumpers (aux pcb not required)
Mate black & gold panel with brass nuts

There are 16 channels, which can be used as:
Midi controller
Manual CV generator (0 to 8v range)
Attenuator
CV to Midi CC
i2C controller
CV to i2C data

The Midi CC number and channels can be different for the TRS jack and the USB port. The firmware has been tweaked to allow also Pitch Bend, which is pretty handy because you can get much better resolution through Midi (from min to max values Midi CCs have 128 steps and Pitch Bend has a resolution of 16.384 steps).

The voltage generated by every fader is up to 8v, which is good enough to control eurorack modules (like wide open/close the cutoff frequency of a filter etc).

In the midi CC messages, 0 volts will correspond to a value of 0, and 8 volts to a value of 127. But the CV to Midi can handle also negative voltages, for such task there are 4 slide switches (1 for every 4 faders) that swaps the internal voltage reference in a way that, when activated, 0 volts will be the middle position of the midi controller, -4 volts the minimum value and +4 volts the maximum. Those switches only affect the Midi/i2C outs, CV outs won't be affected by them in any way.

If you plug in a bigger voltage source (like a -5v+5v LFO or a 10v envelope) the fader will work as attenuator, so you'll be able to adapt how that signal affects the Midi CC out, covering the whole Midi CC range, saturating the waveform or just affecting it briefly.

Panel USB port is type B, which seems to be stronger than mini or micro ones.

i2C could connect directly to an ER-301, monome Ansible or a monome Teletype.

The Teensy can be powered via the internal regulator or the +5v eurorack rail (selectable via a switch on the back).

The partial kit comes with all SMD populated, so only through hole components requires soldering work.

size: 24 HP

92 mA +12V

86 mA -12V
Read more
MRP:$197.89 SAVE 17%
coming soon $164.90
FORTHCOMING
Tesseract Modular Step Fader Dual Sequencer Module
Tesseract Modular Step Fader Dual Sequencer Module (sequencer / slew limiter / CV modulation / dual & stereo synth module)
Cat: 797267 Rel: 31 Jan 21
 
Synth module
Notes: This is a dual sequencer, nothing really new but fun to play with. Oriented to facilitate the interaction of both sequencers in order to get more complex patterns and polyrhythms. Very "hands on" CV source & good complement for more complex digital sequencers like Eloquencer, Performer etc.

There are 3 GLOBAL STYLES:
DUAL (2 totally independent 8 step sequencers)
PARALLEL (one sequencer with 2 rows of CV and 8 steps)
SINGLE (one sequencer with 16 steps)
There are also those PLAY MODES:
Normal
Reverse
Pendulum
Random

There are 2 dedicated buttons (and trigger inputs) to change the sequencer behaviour, pressing 1 button will cycle between the play modes, pressing 2 buttons will do it within the global styles.

Each sequencer has:
8 faders & 8 switches (1 per step)
1 master fader
1 switch for manual step & reset
clock, reset and mode inputs
2 gate outs (activated with the switches, center position is no gate)
1 cv out (0 +8 volts range, unquantized)

There is also an output which is the sum of the 2 CVs of both sequencers and 2 gate outs which are a combination of both sequencer gate lines, pretty handy if it's being used as a 16 steps single sequencer but also interesting when used in dual style.

8 position rotary switch to control the number of steps of the second sequencer, but also other switch allows to send that "reset" signal to the first sequencer instead of the second one, useful for the single 16 step style or to make both sequencers interact.

It has 2 slew limiter circuits with input and output, so they can be used independently, by default processing the CV out of each sequencer, forcing the slew to the max will give as result like a weird-synched LFO, but also the gate outs could be plugged in to get like rudimentary envelopes.

The first sequencer has CV control over step repetition, there's a switch to select the CV IN or the second sequencer as source for such purpose (the master fader has no effect over this, so the 8 lines of the faders correspond to the step repetition, from 1 clock per step to 8) Than means that when used in parallel style the lower row of faders could control the step duration, Metropolis or System 100m style.

Two jumper in the back of the module allows to use the "mode 2" input as reversed CV sum output, giving a total of 6 CV and 6 GATE outs.

26 HP
53 mA +12V
14 mA -12V
Read more
MRP:$209.61 SAVE 17%
coming soon $174.66
FORTHCOMING
Tesseract Modular 12x12 Buffered Matrix Module
Tesseract Modular 12x12 Buffered Matrix Module (multiple / utility synth module)
Cat: 797270 Rel: 31 Jan 21
 
Synth module
Notes: This module is a 12 ins and 12 outs precision buffered matrix.

Is conceived to be a semi-permanent matrix for medium to big systems, with white silkscreen labels to customize ins and outs names.

Every output has a rotary switch to select an input. You can make the same input go through several outputs but not several inputs go to the same output.

There's also a bicolor led next to every output for visual info of the signal that is going through it.

Allows fast patch changes and easy rerouting signals, both audio and cv.

Can be used as a traditional buffered multiple, pretty flexible one: 1 x 12 outs, 2 x 6 outs, 3 x 4 outs etc.

26 HP
45 mA +12V
45 mA -12V
Read more
MRP:$233.04 SAVE 17%
coming soon $194.19
FORTHCOMING
Noise Engineering Sono Abitus Output Module (silver faceplate)
Cat: 795625 Rel: 31 Jan 21
 
High-quality output module
Notes: Sono Abitus is a high-quality output module. It has a stereo pair of Eurorack-level 1/8" inputs that feed a pair of 14" TRS jacks for line output and a 14" headphone output. The headphone output and line outputs have separate level controls, making it easy to monitor while performing or recording.

Size and power:
4 HP

+12v: 50mA

-12v: 50mA

+5v: 0mA

Sono -- from Latin: "to make a noise"

Abitus -- from latin: "way out, exit"

"Make noises exit"
Read more
MRP:$223.93 SAVE 22%
coming soon $173.58
FORTHCOMING
Noise Engineering Sono Abitus Output Module (black faceplate)
Cat: 795629 Rel: 31 Jan 21
 
High-quality output module
Notes: Sono Abitus is a high-quality output module. It has a stereo pair of Eurorack-level 1/8" inputs that feed a pair of 14" TRS jacks for line output and a 14" headphone output. The headphone output and line outputs have separate level controls, making it easy to monitor while performing or recording.

Size and power:
4 HP

+12v: 50mA

-12v: 50mA

+5v: 0mA

Sono -- from Latin: "to make a noise"

Abitus -- from latin: "way out, exit"

"Make noises exit"

Read more
MRP:$223.93 SAVE 22%
coming soon $173.58
FORTHCOMING
NANO Modules QUART Quad Attack-Decay Envelope & Low-Frequency Oscillator Module
NANO Modules QUART Quad Attack-Decay Envelope & Low-Frequency Oscillator Module (CV modulation / envelope generator / function generator / LFO / oscillator / quad synth module)
Cat: 796155 Rel: 31 Jan 21
 
Synth module
Notes: Give shape to your sounds.

An easy-to-handle module, perfect for those functions that you need without overthinking!

QUART has 4 independent functions that can work as Low Frequency Oscillators or Attack-Decay Envelopes depending on whether the Trigger Inputs is connected or not.

If the Trigger Input is not connected, the function will oscillate freely (LFO) but if a patch cable is connected, it will work as an Envelope (AD).
Read more
MRP:$231.74 SAVE 21%
coming soon $182.25
FORTHCOMING
NANO Modules ONA Analogue Multifunction Oscilator Module
NANO Modules ONA Analogue Multifunction Oscilator Module (clock generator / CV modulation / frequency divider / LFO / oscillator synth module)
Cat: 796145 Rel: 31 Jan 21
 
clock generator / CV modulation / frequency divider / LFO / oscillator synth module
Notes: A warm and deep sound source you can rely on

A flexible and warm Analog Multifunction Oscillator, rich in harmonics. Excellent for performance use!

ONA can work as an Audio Oscillator or as a Low Frequency Modulator and it provides control over all its parameters, making it a versatile, deep and easy-to-use oscillator.

Thanks to its triangle-core oscillator and wave-shapers you can choose between a big palette of output waveforms to give shape to your ideas.

Classic Waveforms. Sine, Triangle, Saw and Square.

2 Complex Waveforms with Pulse Width Modulation.

2 Sub-Waveforms to add some bass sounds easily.

Blend them to give unlimited depth to your sound!
Read more
MRP:$231.74 SAVE 17%
coming soon $193.11
FORTHCOMING
NANO Modules ALT Quad Voltage Controlled Amplifier & Cascaded Mixer Module
Cat: 796163 Rel: 31 Jan 21
 
synth module
Notes: 4 VCAs in 8HP designed to keep your signals clean and colourless

VCAs 1, 2, 3. Each one is equipped with a GAIN control, and a CV IN Attenuverter.

VCA 4. GAIN CV IN and the signal normalled to +5V (fully open VCA).

Additionally, the outputs of these channels are cascaded from left to right, allowing ALT to behave as a four-channel mixer.
Read more
MRP:$197.89 SAVE 21%
coming soon $156.22
FORTHCOMING
IO Instruments SPONDE 6-Channel Audio & CV Mixer Module
Cat: 795929 Rel: 31 Jan 21
 
Attenuator / dual & stereo / mixer synth module
Notes: 2 x 6 CH high end AUDIO & CV MIXER

Superb sweet sounding audio quality

Low distortion, low noise, low feedthrough

DC coupled for use as ATTENTUATORs

Flexible routing for mono, stereo, 6- or 12 channels

Overload indicator for output

B-ch IN normalized to A-ch IN

Individual OUTs for channel 1-4

VOLUME sliders with gain of 2

Width: 20 HP
Read more
MRP:$239.55 SAVE 33%
coming soon $159.47
FORTHCOMING
IO Instruments KALYKE Dual Function Generator Module
Cat: 795940 Rel: 31 Mar 21
 
Dual function generator module
Notes: DUAL FUNCTION GENERATOR in audio range speed

LFO section with continuous potentiometer for wide frequency range

OFFSET, PHASE SHIFT and various waveforms

Multiple OUT and negative polarity OUT

LFO modulation to ADSR

Two trigger OUTs of ADSR (AD / AR)

Four modulation INs to control ADSR and its LFO mod

ADSR with selectable curves, loop and ratched mode

Two presets for both channels

Width: 16 HP
Read more
MRP:$225.23 SAVE 26%
coming soon $167.07
FORTHCOMING
IO Instruments CARPO Three-Channel Headphone Amplifier Module
Cat: 795944 Rel: 31 Jan 21
 
Headphone amplifier module
Notes: TRIPLE HIGH QUALITY HEADPHONE AMP

Channel A > 16 OHM (1,2W)

Channel B & C > 32 Ohm (0,5W)

Superb Sound with Low Distortion and great Low End

Linkable Channels (B-A and C-A)

All Inputs with Multiple i.e. feeding Mixer Channels

Mono IN normalized to Stereo

Best protection with Relais

25 mm deep

This Module is a prototype or in a concept phase.
Read more
MRP:$196.59 SAVE 17%
coming soon $163.82
FORTHCOMING
Flame uMLFO MIDI Clock To Analog LFO Module
Cat: 781484 Rel: 31 Dec 20
 
MIDI clock to LFO analog LFO module
Notes: The Flame uMLFO consists of 14 MIDI LFOs which are synchronized to the clock. The module also works with analog clock.

Additional analog clock and reset inputs allow to create pingable LFOs.

It is possible to adjust the frequency, waveform and phase of each LFO. 12 presets are selectable via MIDI keyboard. Thanks to Sysex it is possible to program new setups.
Read more
MRP:$221.32 SAVE 17%
coming soon $184.43
FORTHCOMING
Flame uMGT MIDI To Gates Or Velocity Outs Module
Cat: 781487
 
MIDI to gates/velocity outputs module
Notes: The FLAME uMGT converts 12 Midi notes (one octave) to gates or velocity outputs.
Read more
MRP:$221.32 SAVE 17%
coming soon $184.43
FORTHCOMING
Doepfer A-106-6V XP Multimode Filter Vintage Edition Module
Cat: 790473 Rel: 31 Dec 20
 
Multimode filter module
Notes: Module A-106-6 is a multimode filter that is based on the filter circuit of the Oberheim Xpander. The module features 15 different filter types with 8 filters available simultaneously.

The toggle switch Filter Group is used to switch between 2 filter groups. These filter types are available:
1L (6 dB low pass)
2L (12 dB low pass)
3L (18 dB low pass)
4L (24 dB low pass)
1H (6 dB high pass)
2H (12 dB high pass)
3H (18 dB high pass)
2B (6 dB band pass)
4B (12 dB bandpass)
2N (notch)
3A (allpass)
2H1L (asymmetrical band pass made of a 12 dB high pass and a 6 dB low pass)
3H1L (asymmetrical band pass made of a 18 dB high pass and a 6 dB low pass)
2N1L (combination of notch and 6 dB low pass)
3A1L (combination of allpass and 6 dB low pass)

The module features voltage controlled resonance. For filter group 2 (2L, 4L, 2B ...) even self oscillation is possible. All standard VCF controls are available: manual filter frequency control Frq, one control voltage input with attenuator (FCV2)and one without attenuator (FCV1, ~ 1 V/octave). In addition voltage controlled resonance with manual control (Q) and a CV input with attenuator (QCV) are available. The circuit is based on a 24dB lowpass filter. The outputs of the four internal filter stages (i.e. the 6, 12, 18 and 24dB outputs) are mixed together with different levels and polarities to obtain 15 different filters. Because of this special circuit the outputs have slightly different levels and noise floor. This is caused by the different internal amplifications and numbers of stages that are required to generate the filter in question. If e.g. a filter is derived by one stage only (e.g. the 6 dB, 12dB, 18dB and 24dB low pass) the noise floor is smaller compared to a filter that is derived by a combination of all four filter stages. The module generates a distorted audio signal if the level control is set to about 50% (i.e. center position) or more with A-100 standard signals like VCOs.

Power consumption: 50mA at +12V and 50mA at -12V
Depth: 50mm
HP : 12
Read more
MRP:$207.00 SAVE 17%
coming soon $172.49
FORTHCOMING
AniModule TikTok Module
AniModule TikTok Module (clock modulator synth module)
Cat: 793800 Rel: 31 Dec 20
 
Clock divider & multiplier module
Notes: The TikTok is a 4HP Clock Divider/Multiplier.
It has Divisions and Multiplications of:
*//2
*//3
*//4
*//5
*//6

There is a Clk Input and a Reset Input.
Both are buffered with an opamp based comparator circuit.
They are looking for approximately +1.1V on a rising edge.
This means that you are not constrained to gate (pulse) signals to trigger them.

The Reset input resets your divisions clock counter to 1

There is a switch to select Mathematical or Musical divisions.

The Multiplication Outputs 25MS Trigger pulses.
The Division Outputs are on as long as your Clock source.

Avg Current draw:
40 mA
-9 mA
Peak Current Draw:
80 mA
-17 mA

Width = 4HP
Depth = 38mm
Read more
MRP:$191.38 SAVE 17%
coming soon $159.47
FORTHCOMING
AniModule STD Syncopated Timing Disruptor Module
AniModule STD Syncopated Timing Disruptor Module (clock generator / clock modulator / logic synth module)
Cat: 793790 Rel: 31 Dec 20
 
Syncopated timing disruptor module
Notes: The STD, or Syncopated Timing Disrupter is a dual tap tempo clock with CV control for clock division and multiplication. If one wishes to synchronize the STD with other clocked gear, there is also a Gate input. The CV inputs can shift the clock to being upto 8x faster or /8 to be slower. This function is voltage controllable to turn the STD into a nonstop groove machine. Included in this are three logic functions that output gates depending on how the two channels are interacting. There is OR, ADD, and XOR logic functions.

2 Independent Tap Tempo Clock Channels
Prefer to use a Gate? No Prob! Just Patch in to the Gate Input.

Use the Div/Mult/Offset Pot to Multiply or Divide your Clock Time up to *8 - /8

Or patch In to the CV Input to Modulate the Mathematical Madness!
When CV is being input the Div/Mult/Offset Pot behaves as an Offset.

CV Input wants 0V to +5V, but whatever you got, Between the Offset, and the Front Panel CV Attenuators, it's easy to dial in your desired range of "On the Fly" Mathematical Clock Time Modulations.

Want to sync the 2nd channel to the first?
Latch the Ch1 - Ch2 switch and the Output of Channel 1 is normalled to the jack Switch of Channel 2.
You can still control the Multiplications / Divisions of each channel Independently!

If that wasn't enough to get you poppin' penicillin prophylactically there's more!

The bottom row of jacks constantly output OR, AND, and XOR Logic Combinations of the 2 channels combined!

Want to use something funky (like a Sine Wave / Envelope / Random Voltage Generator) to set the rhythm? The Input is a Buffered Comparator set to trigger at any signal above +1.2V

Perfectly happy up in to the Mid- Audio range.

6HP
+44mA
-16mA
Read more
MRP:$214.81 SAVE 17%
coming soon $179.00
FORTHCOMING
AniModule SOB v1 Module
AniModule SOB v1 Module (state variable filter & waveshaper synth module)
Cat: 794397 Rel: 31 Dec 20
 
State variable filter module
Notes:  A State Variable Filter with an adjustable WaveFolder on the input.

Self-Oscillating Filter Tracks 1V/Oct

Vactrol Input allows you to control CutOff via gates/triggers without using up an EG

Pot to mix "Clean" and "Folded" signal levels

Filter and/or Fold Audio Or Control Voltages

2 Input Signal mixer

1 Input Control Voltage Mixer

1 Input to Vactrol for CV Modulation

1V/Oct In

current Draw: +12V = 31mA -12V = 34mA
Read more
MRP:$229.13 SAVE 17%
coming soon $190.94
FORTHCOMING
AniModule Quad Comparator Module
AniModule Quad Comparator Module (CV modulation / logic / comparater / utility / quad synth module)
Cat: 794399 Rel: 31 Dec 20
 
Quad comparator module
Notes: Simple quad comparator based around the LM339.

It will take your Voltages and turn them into Logic On.

When your signal is higher than the threshold the Gate goes high and the NOT Gate goes low.
When your signal is lower than the threshold the NOT gate goes high and the Gate goes low.

You can set the threshold anywhere from about -10V to +10V.

Input 1 is buffered then normalled to JackSwitches 2->4. So you could send an LFO in to Input 1, set different thresholds for all the inputs and have all the gates/NOT Gates fire at different points from the same LFO.

115 mA +12V
95 mA -12V
29 mm deep
O 5.00 (1 Votes) Average Rating
Read more
MRP:$186.17 SAVE 17%
coming soon $155.13
FORTHCOMING
AniModule MIDI_Gate Module
AniModule MIDI_Gate Module (MIDI synth module)
Cat: 793791 Rel: 31 Dec 20
 
MIDI gate interface module
Notes: The AniModule MIDI_Gate is an easy way to integrate your MIDI-synced workflow with your Modular Synth.

10 Gate Outs that correspond to MIDI notes C1 - A1 (36 - 46).

MIDI NoteOn >> Gate is High

MIDI NoteOff >> Gate is Low

Programmed to receive on MIDI Channel 10

All this in 4HP!!!

Use it to send Multiple Clocks synced to your main Clock.

Use it to trigger events to effect samples piped in via a Line_Amp or TrAniModule in realtime in the analog domain for Live Performance or Resample.

Use it to interface in realtime with your Keyboard, Pad Based Controller, or DAW.

Width = 4HP

Depth = 33mm
Read more
MRP:$203.10 SAVE 17%
coming soon $169.23
FORTHCOMING
AniModule M1xXOR Module
AniModule M1xXOR Module (mixer / sequencer / switch synth module)
Cat: 793792 Rel: 31 Dec 20
 
CV sequencer module
Notes: The Animodule M1xXOR is the Jon Snow of Animodule's product lineup. Described as a "bastard progeny" and "unholy union" by its creators, the module is an amalgamation of the V9a, VCSS, XXX_OR, and MixMan modules. Each of the module's channels, as well as the mixer, can be used independently of the sequencer, enabling a variety of self-contained and inter-module uses. When used independently for self-contained functionality, the module can function as a 4-channel DC-coupled mixer or as 4 individual channels of gated attenuation.

How It Works:
-Signal goes in to Channel Input (it's DC connected so you can use Audio OR CV).
-Signal is attenuated via Channel Attenuator.
-Signal is allowed to pass through to Individual Channel Output AND Mixer Output IF Gate Input is High OR Switch is depressed.

Sequencer:
-Clock Pulse High in to Clock Input Moves Sequence forward 1 Step.
-The Channel that the step is On will be open
-CV can be used to control the Sequencer via the CV Input.
-There is a resolution of 5 steps (4 channels and a 0 step allowing for all channels to be cleared from the Sequencer).
-There is an attenuator and offset to help properly scale and position your CV Input.
-CV Input is expecting 0V to +5V, but with the Attenuator and Offset will easily work with -/+5V.
-Clock and CV maybe used in tandem resulting in some mind melting rhythms!
-In that case the Clock will step forward 1 step from it's current position (unless it's on step 4 in which case it will roll over to step 1)
-The Clock used in conjunction with the CV will bitshift the sequence to the left, incrementing the static position of the step counter by 1 (wrapping around to step 1 after step 4).
-Fer' Instance, 2 Clock counts and CV is on 0. Step will be on Channel 2
-Gate High in to Reset will reset Clock counter to step 1 OR if Clock Input is being used in conjunction with the CV Input the reset will clear the Clock Counter and return the step to where the CV indicates it should be without any BitShifting

*Gate Input / Switches in conjunction with Sequencer:
-The Sequencer and the Gate Input / Switches combine in a XOR gate. If one is High and the other is not, that channel will be open. If BOTH are High, that channel will be closed.

Despite the lengthy description, the M1xXOR is very intuitive (and unbelievably Fun!) to use.
Each Channel (and the Mixer) May be used independently of the Sequencer.
So if you're not in the mood for Rhythmic Insanity You still have a gateable 4 Channel DC-Coupled Mixer AND/OR 4 independent and gateable channels of Attenuation.
You will NEVER just have it filling space in your cabinet.
You will find a use for it in EVERY patch!

All this in 8HP with a depth of 33mm (from rear of Front Panel).
Read more
MRP:$238.25 SAVE 17%
coming soon $198.53
FORTHCOMING
AniModule Gate_Mod Module
AniModule Gate_Mod Module (clock modulator / dual stereo / frequency divider synth module)
Cat: 793797 Rel: 31 Dec 20
 
Gate modifier & trigger delay module
Notes: Got a gate that's gonna make you late? Run it through the Gate_Mod! Got a trigger comin' sooner than you figger'd? Run it through the Gate_Mod!!

Let's face it, couldn't we ALL use a little more length?

This Tiny (yet powerful) Module allows you to manipulate your gate length and delay your event triggers with ease and minimal impact on your HP.

Take an incoming Signal above ~1.1V (OpAmp Comparators on the Inputs make very forgiving Clock Inputs) and shrink it down to 5MS or lengthen it up to 5 Seconds.

That Gate will appear at the Gate Out.

When the Gate is Over a 10MS Trigger will turn on at the Delay Out.

Set the length of the Gate with the Time Potentiometer OR with the CV Input.

The switches allow you to choose between Interrupt OR Dividing Behavior (1 for each channel).

If you have Interrupt selected, when Clock In receives a new Clock Pulse the time will reset, essentially lengthening your Gate Out and Delay Out to the Time you have set + the time that has already elapsed.

So Gate will never go Low and Delay will never go High if you have a Time set longer than the interval between Clock Pulses (Useful if you have staggered, irregular or random Clocks).

When Dividing is selected Clock In will Ignore new Clock Pulses until it has finished the current cycle it's running.

The Delay 1 Out is Normalled via the Jack switch of the Clock 2 Input for all kinds of Timing madness!

Width = 4 HP
Depth = 37mm
Current Draw:
+12V = 35mA
-12V = -18mA

*The Gate_Mod firmware has been updated as of Mid August 2015. There was a bug in the Delay Out section that prevented it from resting at full 0V. All Gate-Mods shipped After the Firmware was updated include the new revision.
Read more
MRP:$191.38 SAVE 17%
coming soon $159.47
FORTHCOMING
AniModule DD Dual VCA Module
AniModule DD Dual VCA Module (CV modulation / panning / VCA / dual stereo synth module)
Cat: 794391 Rel: 31 Dec 20
 
Dual VCA module
Notes: A Dual VCA for Audio or CV.

Mod In 1 is Buffered, Inverted then Normalled to Mod In 2, to facilitate stereo panning and VC CrossFading without a bunch of support modules.

Don't want it? Just turn the attenuator down or plug a signal of your choosing in to the Mod In 2.

Current Draw: +12V = 25mA, -12V = -22mA

8HP, 28mm Deep
Read more
MRP:$200.49 SAVE 17%
coming soon $167.07
FORTHCOMING
4MS Percussion Interface & Expander Modules
Cat: 794765 Rel: 30 Oct 20
 
Envelope follower/envelope generator/external/expander synth module
Notes: The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.

Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.

Electrical and Mechanical Specifications:
Module size (PI):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
10-pin Eurorack power header

Module size (PI EXP):
4 HP Eurorack formal module
0.98" (25mm) maximum depth with power cable
8-pin cable connects to PI

Power consumption:
with PI Expander
+12V: 104mA
-12V: 65mA
without PI Expander
+12V: 69mA
-12V: 56mA

Audio Inputs:
1/8" [3.5mm] on PI main module, and 1/4" [6.35mm] on PI Expander
100k input impedance, AC-coupled

Audio Outputs:
Voltage range: -10.4V to +10.8V, DC-coupled
1k output impedance
Gain Characteristics
Gain range: < -100dB to +54dB (500x)
Clip light turns blue when signal (post-gain) exceeds 2.5Vpp
Gate is triggered when signal (post-gain) exceeds 6.3Vpp
Clip light flashes red when signal clips on Audio Out jack (exceeds +10.8V)
Gate Out Jack
1k output impedance
+8V gate/trigger signal
6ms - 0.5s pulse width
+ Env Out jack (jack on PI main module)
1k output impedance
+9V peak (sustain), -60mV resting (off)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
- Env Out Jack (jack on PI main module)
1k output impedance
+9V resting (off), -150mV peak (sustain)
15ms attack time
70ms - 6s exponential decay time (1% of peak voltage)
Env. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-60mV minimum
Inv. Out jack (attenuated jack on PI Expander)
1k to 26k variable output impedance
+9V maximum
-150mV minimum
Included with the PI+EXP:
8-to-16 pin power cable
8-to-8 pin cable for connecting to the Expander
M3 Knurlie screws (4)
Read more
MRP:$196.59 SAVE 21%
coming soon $156.22
Click for better price!
or call +44 20 7424 1960
quote 794765
Artículos del 1 al 24 de 24 en la página 1 de 1

Filter

Coming Soon: Studio Equipment
Close