100% Compra Segura

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Compra Segura

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Coming Soon: Studio Equipment

Inicio  Coming Soon  

Studio Equipment

Options
Artículos del 1 al 26 de 26 en la página 1 de 1
FORTHCOMING
Doepfer A-118-2V Noise & Random Slim Line Vintage Edition Module
Cat: 790467 Rel: 31 Dec 20
 
Signal generator module
Notes: Module A-118-2 generates the signals white noise, colored noise, continuous random voltage and stepped random voltage.

The noise signal is generated 100% analog by amplification of the noise of a transistor. White and colored noise are usually used as audio sources. The random voltages are normally used as control voltages (e.g. for filter frequency or any other voltage controlled parameter).

The A-118-2 gives you the ability to mix the relative amounts of Red and Blue noise (low/high frequency component) in the colored noise output.

For the continuous random voltage the rate of change (Rate) and amplitude (Level) of the random voltage can be adjusted. The continuous random voltage is used as source for the S&H/T&H unit. The type of operation can be set to S&H (sample and hold) or T&H (track and hold). When T&H is chosen the output signal follows the input signal as long as the Clock input is "high". As soon as the clock signal changes to "low" the last voltage is stored. When S&H is chosen the input signal is sampled at the rising edge of the Clock signal. For the Clock signal a "digital" signal (e.g. Clock, Gate, rectangle output of an LFO) is required. Dual color LEDs are used to indicates the continuous and stepped random voltages.

Controls:
Blue: share of the high frequencies in the the colored noise output
Red: share of the low frequencies in the the colored noise output
Rate: rate of change of the continuous random voltage
Level: amplitude of the continuous random voltage
TH/SH: switches between T&H und S&H

Inputs and outputs:
RND: continuous random voltage output (with LED display)
TH/SH: stepped random voltage output (with LED display)
Clk: Clock input of the S&H/T&H unit
C Noise: colored noise output
W Noise: white noise output

Important notes:
After power on it takes a few minutes until the two noise signals and the random signals are generated. The module is not faulty when after power on the signals do not appear immediately!

The S&H/T&H function is realized by pure analog circuitry (electronic switch followed by a holding capacitor and buffer). Consequently the output voltage drifts a bit in the holding state because the capacitor is discharged by parasitic resistors. The drift depends also upon environmental conditions like humidity or temperature.

The level of the random voltage changes with the settings of the Blue and Red controls. Especially the Red control affects the random voltage level (which is derived by low pass filtering from the colored noise signal) because the Red control changes the share of the low frequencies in the colored noise signal. The effect of the Blue control is much smaller because it changes the share of the high frequencies in the colored noise signal which are filtered out by the low pass of the random circuitry.

Power consumption: 20mA at +12V and 20mA at -12V
Depth: 40mm
HP : 4
Read more
MRP:$106.97 SAVE 17%
coming soon $89.14
FORTHCOMING
Zlob Modular Triple Cap Chaos Chaotic Oscillator & Audio Mangler Module
Zlob Modular Triple Cap Chaos Chaotic Oscillator & Audio Mangler Module (chaotic oscillator & audio mangler synth module)
Cat: 793149 Rel: 31 Dec 20
 
Analogue noise oscillator/audio mangler module
Notes: The Triple Cap Chaos(C^3 Chaos) is a 2hp analog, chaos based, noise oscillator, pseudo ring modulator/harmonics generator, and audio mangler Eurorack module available as a DIY Eurorack kit, PCB and Panel, or built.

It is a unique module, like the Diode Chaos, because it has never existed as a musical instrument until now. There is also no other module to my knowledge that can do exactly what the Triple Cap can do. The circuit(with several modifications) is based on the paper "Simple Autonomous Chaotic Circuits" by J.C. Sprott and Jessica R. Piper. As opposed to the Diode Chaos that generates control voltage this module focuses on the audio rate.

The "Emanate" potentiometer controls the coarser overall spectrum of the chaos, from lots of activity counter clock wise up to less chaos and more of a steady oscillation. The "Width, CV ATT" potentiometer can be thought of as more of a fine control for the chaos/oscillator. When something is inserted into the "CV" in the voltage normalization from the width knob is broken and the potentiometer now acts as an attenuator for the incoming cv. The Triple Cap is not a traditional volt per octave exponential VCO, and has a sort of narrow frequency range to exploit the chaotic behavior.

It expects a +5v to -5v max signal in to modulate the chaos. The "IN" jack is an A.C. coupled input for audio in, although cv and audio can work for both the "CV" in jack and "IN." The "IN" will interfere and interact with the onboard chaotic oscillator depending on the frequency of the input, which may take some experimentation. It can create ring mod ish sounds, to added harmonics, to almost bit crushed sounds depending on the "X" or "Y" output. The "X" output is a more windy noisy sinusoidal based output and the "Y" output is more squared off and aggressive, harsher sounding output.

Some quirks about the Triple Cap: The "X" output can offset negatively or positively a little bit depending on the pot settings, but both outputs tend to stay around 10vpp. With the "Emanate" and "Width" pots all the way up the typical frequency will be around 150hz although some will reach 200hz at this setting. With the "Emanate" pot full counter clock wise "Width" pot full clock wise the frequency will be around 250hz. It is possible to send signals into the triple cap that can bring it out of the desired range causing the oscillation to cut out.

The Triple Cap has a double sided panel. meaning one side has the classic graphics and the other is Soulless with less graphics.

Read more
MRP:$91.32 SAVE 17%
coming soon $76.09
FORTHCOMING
2hp Pmkn Mult Signal Splitter Module (limited edition module)
2hp
Cat: 797074 Rel: 31 Jan 21
 
2-input/6-output signal splitter module
Notes: The Limited Edition Pumpkin Mult is here! Craft sonic concoctions with this pulp-free multiplier, exclusive to our newsletter community for a limited time. The Pmkn will go public after the weekend, so carve 'em out while you can. It's a ghoulishly good time!

Mult is a 2 input, 6 output signal splitter. Channel 1 is normalled to channel 2 when no cable is present, allowing the user to split an input signal six ways, or two input signals with three outputs each.

Read more
coming soon $51.08
FORTHCOMING
Zlob Modular Dual VCA Dual Summed Voltage Controlled Amplifier Module
Zlob Modular Dual VCA Dual Summed Voltage Controlled Amplifier Module (dual summed voltage controlled amplifier synth module)
Cat: 793170 Rel: 31 Dec 20
 
2-channel Voltage controlled amplifier/mixer module
Notes: The Dual VCA is a 2hp 2 channel Analog VCA and Mixer Eurorack Module available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

It is a DC coupled OTA(LM13700) Dual Linear VCA based on the same fabled design of the VnIcursal VCA. The 2 VCAs are summed together so it can be used as a voltage controlled mixer at the "SUM OUT" or all 3 outs can be used separately and simultaneously. 5 volts into the CV in will provide unity gain, anything above 5 volts can clip the input.
Read more
MRP:$103.06 SAVE 17%
coming soon $85.88
FORTHCOMING
Zlob Modular Diode Chaos Chaotic Voltage Generator Module
Zlob Modular Diode Chaos Chaotic Voltage Generator Module (chaotic voltage generator synth module)
Cat: 793141 Rel: 31 Dec 20
 
Voltage generator module
Notes: Diode Chaos is a 3hp analog chaotic low frequency voltage generator Eurorack Module available as Eurorack DIY Kit, PCB and Panel, or Built Module.

It is a unique module because it has never existed as an electronic music instrument until now. The module is based on a circuit from a paper called "A simple chaotic circuit with a light-emitting diode" written by Volos, Wang, Jafari, and Kapitaniak.

Diode Chaos produces 3 phases of interrelated morphing voltages including a chaotic trigger out. The range is 20-30 seconds a cycle up to audio rate, although only the X out and TRIG out go up to audio rate. The frequency is controlled by the RATE knob. Each output exhibits different behavior at different rate settings. X,Y, and Z outs like to stay in the 4vpp range although at different RATE settings the outs can reach 10vpp. The TRIG out chaotically releases 0-10v triggers although sometimes it will spit out smaller voltage peaks.

LED soldermask windows provide constant display of positive and negative voltage crossings.

Differences between chaos and random(some quoted and summarized material from Ian Fritz's site):

Chaos is "highly irregular, but still contained within a finite region (the "strange attractor")"

Chaos occurs in 3 dimensions.

Chaos needs a non-linear element (with Diode Chaos the nonlinear element is a red LED, and the chaos is directly visible and useable at the TRIG out).
Read more
MRP:$96.53 SAVE 17%
coming soon $80.44
FORTHCOMING
Zlob Modular Minimix User Configurable 3-Channel Mixer Module
Zlob Modular Minimix User Configurable 3-Channel Mixer Module (user configurable 3-channel mixer synth module)
Cat: 793175 Rel: 31 Dec 20
 
3-channel user configurable mixer module
Notes: Minimix is a Simple 2hp 3 Channel Unity Gain Audio or Control Voltage Mixer Eurorack Module available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

Version 2 adds jumper selectable AC or DC coupling and linear or logarithmic operation for each channel. The newly revised MiniMix is now all through hole and aimed more to the beginner solderer. There is also a trimmer on the PCB to increase the master gain up to 2 or more for all 3 channels.

The module ships with a black and white reversible pcb panel.
Read more
MRP:$91.32 SAVE 17%
coming soon $76.09
FORTHCOMING
Zlob Modular Skew Fade LFO Analogue Low Frequency Oscillator Module
Zlob Modular Skew Fade LFO Analogue Low Frequency Oscillator Module (analogue low frequency oscillator synth module)
Cat: 793139 Rel: 31 Dec 20
 
Analogue LFO module
Notes: The Skew-Fade LFO is a 3hp Analog Low Frequency Oscillator Eurorack Module capable of a plethora of waveforms, available as a DIY Eurorack Kit, PCB and Panel, or Built.

It has three rate settings ranging from 3 minutes and 30 seconds a cycle up to audio range at 20 hz. Triangle waves can be skewed between ramps and saws, and square waves pulse width can be adjusted from inverted triggers to triggers. The LFO's unique feature is voltage controlled cross fading through the ("Fade C.V." in) between square/shark tooth\sine waveforms provided at the "Fade Out." All outs are also influenced by the skew knob resulting in many complicated and asymmetrical possibilities at the "Fade Out." It can even be self patched(ie triangle or square into fade cv) for an extended pallet of waveforms. The "Fade C.V." in expects a bipolar voltage 10vpp to fade from square to sine with the fade pot at noon position. Bicolor led provides constant display of positive and negative voltage crossings.
Read more
MRP:$96.53 SAVE 17%
coming soon $80.44
FORTHCOMING
Zlob Modular Entropy Expander Analogue Random Voltage & Noise Generator Module
Zlob Modular Entropy Expander Analogue Random Voltage & Noise Generator Module (analogue random voltage & noise generator synth module)
Cat: 793160 Rel: 31 Dec 20
 
expansion
Notes: The Entropy Expander is a 3hp Analog Random Voltage Generator that expands upon the features of the Entropy Euroack Module. Available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

The Entropy+Expander packs together some of the most random voltage options in 6hp. It provides a controllable "Glide"(slew) out for the S/T\H, a comparator with a controllable rate("Thrsh") of random gates("Rand Gate") out with an input to compare other waveforms(Comp In, inserting a cable into here breaks the white noise normalization), and high pass filtered white noise resulting in approximate "Blue noise" (+3db/octave) and "Violet noise"(+6db/octave) outs.

The unique part of the circuit is a voltage controlled A/B switch thats normalled to the "Rand Gate" out that's switching between the S/T\H out(left Blue led window)and Infra out(right Red led window), the Glide control also effects the S/T\H coming out of the switch so you can get really random results from the "Entropy Out." Inserting a cable into "Switch CV In" breaks the random gate normalization and lets you toggle between A/B(left S/T\H out and right Infra out, indicated by the led windows) with your own gate or trigger.

There is a jumper on the pcb to select if you want glide on the s/t\h at, Entropy out, or un-slewed operation. There is also a trimmer for setting the amplitude of the incoming signal at "Comp In" which sets the frequency range of random gates. This may have to be adjusted depending on your Entropy version.

The random gate range can also be set up more as a noise oscillator by turning the pcb trim(clockwise) up or it can be set so random gates are extremely slow(trim counter clockwise) with minutes between random gates.
Read more
MRP:$91.32 SAVE 17%
coming soon $76.09
FORTHCOMING
Zlob Modular Mineq Simple 3-Band Equaliser Module
Zlob Modular Mineq Simple 3-Band Equaliser Module (simple 3-band equaliser synth module)
Cat: 793166 Rel: 31 Dec 20
 
3-band Equalizer Eurorack module
Notes: The MinEq is a 2hp simple 3 Band Equalizer Eurorack Module available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

It provides boost or cut control over the Low, Mid and High frequency bands of an audio input. The circuit is capable of up to 20vpp~ of boost(with a 10vpp signal) and attenuation down to 1-2vpp depending on the input. The frequency bands are centered near 50Hz(Low), 1kHz(Mid), and 10kHz(High). The circuit is AC coupled and will invert the input. With all the potentiometers at noon, the MinEq passes the signal relatively unaltered. The only SMD component is the IC.
Read more
MRP:$84.79 SAVE 17%
coming soon $70.65
FORTHCOMING
Doepfer A-119V External Input & Envelope Follower Vintage Edition Module
Cat: 790461 Rel: 31 Dec 20
 
External input & envlope follower module
Notes: Module A-119 (External Input / Envelope Follower) is designed to allow external audio signals to be integrated into the System A-100. It comprises a pre-amp, envelope follower, and comparator.

The pre-amp has two inputs: an unbalanced input for line level signals, with a gain factor of from 0 to 20, and a balanced input with a gain factor of from 0 to 500, for insertion of low level signals, for instance from a microphone or electric guitar. The Envelope Follower reads the signal level of the input, and puts out a proportional voltage as an envelope at its own output. The comparator generates a gate signal whenever the input goes above an adjustable trigger threshold. Three LEDs help you keep track of overload, the envelope, and the gate signal.

Power consumption: 30mA at +12V and 20mA at -12V
Depth: 45mm
HP : 8

The module was designed primarily to derive an envelope and gate signal from the incoming audio signal. The built-in preamp is not "high-end" and shows - depending upon the position of the gain control - a reduction of higher frequencies in the frequency response. It is possible to improve the frequency response by replacing IC1 (the upper of the two integrated circuits) by a more sophisticated circuit. For example the LME49740 can be used. It's no longer in production but available e.g. via Ebay.

Apart from this an incoming audio signal with sufficient level can be patched directly to the audio input of A-100 modules (e.g. filters), i.e. without the detour via the A-119. In this case the A-119 functions only as envelope and gate generator and the audio output of the A-119 remains unused.
Read more
MRP:$95.23 SAVE 17%
coming soon $79.35
FORTHCOMING
Noise Engineering Horologic Uter Clock Generator & Expander Module For Horologic Solum (black faceplate)
Cat: 795624 Rel: 31 Jan 21
 
Clock generator & expander module
Notes: Horologic Uter is an optional expander for Horologic Solum that offers an extra seven outputs at fixed, musically useful, divisors.
Read more
MRP:$108.27 SAVE 17%
coming soon $90.22
FORTHCOMING
Wavefonix 3 Channel Audio Mixer Module
Cat: 796510 Rel: 14 Dec 20
 
Audio mixer module
Notes: This mixer has three AC-coupled channels, each with a logarithmic unity-gain attenuator; suitable for mixing audio signals from modules such as VCOs etc.

Specifications

Format: Eurorack
Width: 8hp
Depth: approx. 25mm
+12V: 20mA
-12V: 20mA
+5V: 0mA
Read more
coming soon $88.04
FORTHCOMING
Zlob Modular Push VCA Dual Summed Mute Module
Zlob Modular Push VCA Dual Summed Mute Module (dual summed mute synth module)
Cat: 793173 Rel: 31 Dec 20
 
Dual summed mute Eurorack module
Notes: The Push VCA is a 2hp 2 Channel DC Coupled Mute Eurorack Module available as a Eurorack DIY Kit, PCB and Panel, or Built Module.

It features 2 independent unity gain DC coupled VCAs with led push button mutes. A mix of both channels is available at the sum, but all outputs are available simultaneously. The newest version has normalizations to +5v, so with nothing plugged into the ins voltage can be toggled on and off at the outputs and up to 10 volts can be output at the sum. At checkout specify if you want latching or momentary push buttons. led button color may vary between red and yellow. but it will always be 2 of the same color.

Read more
MRP:$114.80 SAVE 17%
coming soon $95.66
FORTHCOMING
AniModule AnVilope Module
AniModule AnVilope Module (clock generator / envelope generator / LFO synth module)
Cat: 794381 Rel: 31 Dec 20
 
Envelope generator module
Notes: A Simple, Affordable, 4HP, Analog Envelope Generator.

Attack, Decay, Release... Simple.

- Envelope Out 0V to +7V
- Loop function so you can use it as a Variable Wave-Shape LFO / Timer
- Inverted out that goes from +7V to 0V

Function:
When the gate is High the envelope will rise and cycle through it's phases.
When gate goes low again the envelope will revert to the release phase.

If the Gate is longer than the ADR phases, the decay will play out then go to release and the envelope will end after the release.

Sprinkle them all over your system!

4HP Depth : 28mm
Read more
MRP:$112.19 SAVE 17%
coming soon $93.48
FORTHCOMING
Wavefonix Clock Divider Module
Wavefonix Clock Divider Module (utility synth module)
Cat: 796525 Rel: 14 Dec 20
 
Clodk divider module
Notes: This Clock Divider (CD) module allows an input clock signal to be divided into exact divisions (down to 1/128) of the original frequency. This is especially useful for applications such as creating a sub-oscillator etc.

The module can also act as an audio divider by accepting inputs such as sine, ramp or triangle waveforms and outputting corresponding, divided clock signals.

A reset input allows the divisions to be synchronised.

Specifications

Format: Eurorack
Width: 6hp
Depth: approx. 40mm
Power consumption:
+12V: 70mA
-12V: 20mA
+5V: 0mA
Read more
coming soon $95.66
FORTHCOMING
Wavefonix Attenuverter Module
Wavefonix Attenuverter Module (utility synth module)
Cat: 796526 Rel: 14 Dec 20
 
Attenuverter module
Notes: Attenuverter (AV) is one of Wavefonix's most versatile modules; allowing the polarity of an input source such as an envelope or a ramp wave from an LFO to be inverted.

Additionally, an offset voltage between approximately -10V to +10V can be applied to the input source. The module can also act as an independent CV source when there is no input.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 25mm
Power consumption:
+12V: 30mA
-12V: 20mA
+5V: 0mA
Read more
coming soon $88.04
FORTHCOMING
Wavefonix R2R DAC Module
Wavefonix R2R DAC Module (utillity / passive synth module)
Cat: 796533 Rel: 14 Dec 20
 
Digital-to-analogue conversion module
Notes: The R2R DAC is an ingenious design. It consists of a string of resistors connected to another set of resistors. There are no active components in this module and it provides an affordable and easy way of converting digital signals to analog signals with great accuracy.

Digital-to analog conversion with the R2R is straight-forward. Inputting a digital signal into any of the eight data inputs (1 to 128 in binary) will provide an analog output from the In/Out socket.

Waveform's Clock Divider (CD) module complements the R2R DAC very well. For example; inputting various combinations of clock signals from the Clock Divider into the 1 to 128 inputs of the R2R DAC provides some interesting outputs from the In/Out, such as a stepped ramp wave. The number of input signals determines the resolution i.e. there are eight inputs (each corresponding to a bit), so therefore the maximum resolution is 8-bit. The resulting output can be fed into the CV input of a VCO, LFO, quantizer, filter and many other modules. There are many different combinations that can be experimented with.

Other uses for the R2R DAC include as an 8-channel mixer by inputting analog signals into any of the 8 inputs (1 being the quietest and 128 being the loudest) and the resultant mixed signal is given from the In/Out.

Similarly, the module can be used as an attenuator and multiple by inputting a signal into the In/Out and the attenuated signals are output from the eight binary inputs (again with 1 being the most attenuated and 128 being the least attenuated).

Specifications

Format: Eurorack
Width: 4hp
Depth: approx.15mm
Power consumption:
+12V: 0mA
-12V: 0mA
+5V: 0mA
Read more
coming soon $56.52
FORTHCOMING
Wavefonix Linear Attenuator Module
Wavefonix Linear Attenuator Module (utility / passive synth module)
Cat: 796534 Rel: 14 Dec 20
 
Linear attenuator module
Notes: Wavefonix's Linear Attenuator (AT) features three linear unity-gain attenuators; suitable for attenuating both audio and CV signals.

It is also a passive module; meaning that no power is required for it to function.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 15mm
+12V: 0mA
-12V: 0mA
+5V: 0mA
Read more
coming soon $64.13
FORTHCOMING
Wavefonix 4x4 Passive Multiple Module
Wavefonix 4x4 Passive Multiple Module (utility / passive synth module)
Cat: 796529 Rel: 14 Dec 20
 
Passive multiple module
Notes: This module is a quad, four-way passive multiple, suitable for splitting CV signals from modules such as LFOs or envelopes etc.

The passive design means that no power is required for the module to function.

Specifications

Format: Eurorack
Width: 7hp
Depth: approx. 15mm
+12V: 0mA
-12V: 0mA
+5V: 0mA
Read more
coming soon $71.73
FORTHCOMING
Wavefonix 3x3 Passive Multiple Module
Wavefonix 3x3 Passive Multiple Module (utility / passive synth module)
Cat: 796531 Rel: 14 Dec 20
 
Passive multiple module
Notes: This module is a triple, three-way passive multiple in a compact but ergonomic design; useful for splitting CV signals from modules such as LFOs or envelopes etc.

Being passive; no power is required for the module to function.

Specifications

Format: Eurorack
Width: 4hp
Depth: approx. 15mm
+12V: 0mA
-12V: 0mA
+5V: 0mA
Read more
coming soon $56.52
FORTHCOMING
Wavefonix 3 Channel Linear Mixer Module
Cat: 796506 Rel: 14 Dec 20
 
Linear mixer module
Notes: This mixer has three DC-coupled inputs, making it perfect for mixing both audio or CV signals from sources such as VCOs, LFOs and envelopes etc.

Each channel features a unity-gain, linear attenuator.

Specifications

Format: Eurorack
Width: 8hp
Depth: approx. 25mm
Power consumption:
+12V: 10mA
-12V: 10mA
+5V: 0mA
Read more
coming soon $79.35
FORTHCOMING
Wavefonix Dual Sample & Hold Module
Wavefonix Dual Sample & Hold Module (utility synth module)
Cat: 796520 Rel: 14 Dec 20
 
Dual sample & hold module
Notes: Featuring two dedicated sample and hold channels, this module is perfect for creating stepped voltages from a random noise source, downsampling waveforms and even creating arpeggios.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 40mm
Power consumption:
+12V: 40mA
-12V: 30mA
+5V: 0mA
Read more
coming soon $88.04
FORTHCOMING
Wavefonix Dual Linear Slew Limiter Module
Wavefonix Dual Linear Slew Limiter Module (envelope generator synth module)
Cat: 796521 Rel: 14 Dec 20
 
Dual lwer limiter module
Notes: This module comprises two linear slew limiters, useful as a basic A/R envelope generator, gate delay or low-pass filter.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 25mm
Power consumption:
+12V: 40mA
-12V: 50mA
+5V: 0mA
Read more
coming soon $79.35
FORTHCOMING
Wavefonix Dual Logarithmic Slew Limiter Module
Wavefonix Dual Logarithmic Slew Limiter Module (envelope generator / utility synth module)
Cat: 796524 Rel: 14 Dec 20
 
Dual slew limiter module
Notes: This module comprises two logarithmic slew limiters, useful for a range of different applications, such as adding portamento to a keyboard, or as a basic A/R envelope generator, gate delay or low-pass filter.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 25mm
Power consumption:
+12V: 40mA
-12V: 30mA
+5V: 0mA
Read more
coming soon $79.35
FORTHCOMING
Wavefonix Logarithmic Attenuator Module
Wavefonix Logarithmic Attenuator Module (utility / passive synth module)
Cat: 796536 Rel: 14 Dec 20
 
Attentuator module
Notes: Wavefonix's Logarithmic Attenuator (AT) features three logarithmic unity-gain attenuators; especially suitable for attenuating audio signals. However, it can also be used to attenuator CV signals.

It is also a passive module; meaning that no power is required for it to function.

Specifications

Format: Eurorack
Width: 5hp
Depth: approx. 15mm
+12V: 0mA
-12V: 0mA
+5V: 0mA
Read more
coming soon $64.13
FORTHCOMING
AniModule Line_Amp Module
AniModule Line_Amp Module (multiple / preamp / utility / dual stereo / external synth module)
Cat: 793793 Rel: 31 Dec 20
 
Buffered multiple module
Notes: Check out AniModule's Line to Synth Level Converter.

2 Channels of 1 in <--> 2 Out.

Each channel is designed to multiply your input by *3 to boost your Line Gear / Tablet / Phone so you can integrate audio OR Control Voltages from your auxiliary systems.

Each channel's input is designed with Line Level gear's input impedance in mind.

Perfectly compatible with Synth Output Impedances, but the standard Synth Input Impedance is higher than Line level equipment is expecting.

Don't need to amplify your XPhone right this minute? Never fear! Just Hit the Switch!

This module won't sit unused in your cabinet breeding resentment and dust bunnies.

Hit the switch and that channel becomes a normal 2 HP Unity Gain Buffered Mult.

Only need one channel of each? It's YOUR Choice!
Read more
MRP:$108.27 SAVE 17%
coming soon $90.22
Artículos del 1 al 26 de 26 en la página 1 de 1

Filter

Coming Soon: Studio Equipment
Close