100% Compra Segura

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Compra Segura

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

Filters

Inicio  Equipment  

Filters

Options
Artículos del 1 al 3 de 3 en la página 1 de 1
Subscribe to our weekly Studio Equipment emails
Boredbrain Transmutron Dual FX Loop Crossover Filter
Cat: 704118 Rel: 11 Jan 19
 
Nexus for effects pedals & Eurorack effects modules
Notes: Are your effects chains suffering from radioactive decay? The Transmutron allows you to combine pedals (and Eurorack effects) within its sonic reactor to create new and exciting compounds! Different results can be achieved using one of three modes: Fission (crossover filter), Fusion (crossfader), and Fallout (resonant wide-notch filter).

In the primary mode, Fission, the signal from your guitar, bass, synth, or drum machine is split into separate frequency bands, sent simultaneously to different effects, and then recombined to a single output (or two separate outputs). The Splitpoint parameter can be controlled manually or with an expression pedal, and simultaneously injected with a control voltage (CV) source for extremely dynamic reactions!

In Fusion mode, the Splitpoint instead acts as a pre-FX level crossfader, rather than splitting the signal into separate bands. This allows for less extreme blends, especially when modulating. In the third mode, Fallout, a resonant wide-notch filter is applied to both pre-FX channel signals, cutting a hole and creating a phasing-wah effect when using an expression pedal or LFO to sweep the Splitpoint back and forth.

To further shape the signals sent to your effects, the Transmutron is equipped with dedicated hi and low cut filters. In Fission and Fallout modes, the cutoff frequencies of these filters also define the end-to-end sweepable range of the Splitpoint parameter and its centre frequency. The filters have selectable slopes of 12, 24, or 48 db/oct, which also affects the crossover filter, and greatly enhances the resonance of the wide-notch filter. If further separation of the parallel FX channels is needed, a dedicated phase switch is on-hand.

Both FX channels have two sets of sends and returns: 1/4-in for guitar pedals and line-level effects, and 3.5mm for Eurorack level processing. For each channel, the 1/4-in and 3.5mm FX loops can be used simultaneously, as they are in series (3.5mm then 1/4-in). The FX sends are half-normalled so they can be used as buffered copies without affecting the returns. Additionally, the 3.5mm FX loops for each channel can be independently switched to pedal/line-level using internal dip switches, which allows for seamless integration with the Boredbrain Patchulator 8000.

How complex the reaction is up to you! From simple tone shaping using only a couple effects, to interconnected combinations of pedals and Eurorack modulation madness, the Transmutron is just the tool you need to reactivate your effects!
Read more
 2 in stock $324.32
Mode Machines OMF-1 Oakley Moog Style Analog Filter
Cat: 510772 Rel: 18 Nov 15
 
4 pole true analog filter based on the transistor ladder filter developed by Moog
Notes: A four pole true analogue filter. This is based on the famous transistor ladder filter developed by Dr Bob Moog in the 1960s. A front panel pot controls the filter cut-off frequency, another controls the resonance. The resonance control is configured not to cause volume drop when turned up. The filter can be made to oscillate if required.

Two filter outputs are available. One is the Fizz output. This is a type of -6dB/octave filter and it gives a unique filtering effect with a real bite. The other is the Smooth output. This is a classic -24dB/octave filter, and gives a smooth warm analogue filter sound. Each filter output goes via its own reversible attenuator. This means not only can you adjust the output level, but also the phase of the output signal. This allows complex filter shapes to be made when the two outputs are mixed together in various degrees. This includes a very nice sounding band pass filter.

A wet/dry control allows the filtered audio to be mixed with the original signal. Not only is this useful in controlling the depth of the effect, but it can also create unusual phasing and vibrato type effects.

A wide range pre-amplifier is included. You can use the OMF-1 with virtually any input from guitars to synthesisers. A peak indicator will allow you to monitor overloads, although the OMF-1 is designed to overdrive beautifully.

An inbuilt low frequency oscillator with triangle and square waveforms. The frequency can be changed from 0.05Hz (one cycle in 20 seconds) to over 50Hz. A bi-colour LED gives visual indication of the speed of the LFO. Use the LFO to create auto wah and phaser type effects. The LFO can also be selected to trigger the envelope generator.

An ingenious dynamic envelope section that can move the filter cut off point up or down. It can be put into one of three modes at a flick of a switch:
FLR: It can function as a useful envelope follower, with controllable attack and decay times. Perfect for simulating many classic dynamic follower filter boxes. Play louder and hear the filter open up.
AD: It can be a standard attack-decay envelope generator. This is a type of one shot envelope, that rises and falls at the presence of an initial trigger signal. Useful for percussive type sounds.
AR: It can be a standard attack-release envelope generator. This is triggered either by the LFO, external gate signal or by an automatic audio trigger circuit with a variable threshold level. Powerful for creating rising crescendos.

The final output volume can be controlled with a level control. The output circuitry is configured to drive long length cables with ease and without ground loops.

A side chain input is available. This is a second audio input that can control the main input, but is not heard directly. Use this to trigger the envelope generator, or drive the envelope follower. A common use of this is to make the main audio program respond to a drum machine's output for syncopated effects. Use a deep rich string patch as your main input, and listen to the drum machine automatically pulse the output to the beat. Awesome!

CV and gate inputs are available for connection to a modular synth or midi-CV convertor. The CV input will control the filter frequency, and the gate control will trigger the envelope generator if selected.

With a second OMF-1 a stereo unit may be built. The two channels can either be run independantly or linked together for true stereo processing.
Read more
 1 in stock $270.98
Vermona Filter Lancet (includes UK power supply)
Cat: 433132 Rel: 19 Aug 11
 
Analogue multimode desktop filter, includes UK power supply
Notes: The Vermona Filter Lancet is a compact but versatile stand-alone multimode filter for your desktop. It's the right weapon against static sound and boredom and made for any kind of audio signal. The filter section itself has 3 modes: low-pass, high-pass and band-pass. The last one works with a slope of 12 dB per octave whereas low- and high-pass are 24 dB filters.

You can give the filter some extra punch with the Balls knob, known from Kick Lancet. It pushes low and high frequencies of the signal before being filtered. And of course the resonance is self-oscillating.

Other than the filter section of Mono Lancet, the Filter Lancet is not based on (Moog-) cascade circuitry. It was inspired by the filters of the Vermona M.A.R.S. respectively DAF-1 and Action Filter.

Without modulation the Filter Lanced would still be a good filter but kind of boring. So it is equipped with a LFO, an envelope generator, an envelope follower and a CV/pedal input. The LFO has 2 frequency ranges and goes up to 250Hz - that's fast. At low frequencies the LFO can be re-triggered by gate- or audio signals. It has sample & hold and five waveforms: saw up and saw down, square, sine and triangle.

The envelope generator can be triggered by the input signal or an additional audio signal as well as by a gate voltage. If triggering it via gate it works as an attack-sustain-release envelope. With audio triggers its mode is attack-decay. The envelope follower transforms the contour of the input signal into control voltages that can serve as modulation source.

The LFO modulation intensity can be set separately from modulation intensity of envelope generator and envelope follower on the VCF- as well as on the VCA section.

The Filter Lancet features a drive circuit right in the input section to add subtle shades of overdrive up to solid distortions.

The Filter Lancet is packed with useful features. It's a great and powerful addition to any synthesizer including Mono Lancet with or without Modular Dock. But Filter Lancet also is designed for stringed instruments. It creates standard effects like WahWah and tremolo with ease and even adds a palette of extraordinary sounds to any effect repertoire.
Read more
MRP:$442.73 SAVE 23%
 2 in stock $340.64
Click for better price!
or call +44 20 7424 1960
quote 433132
Artículos del 1 al 3 de 3 en la página 1 de 1

Filter

Filters
Accesorios
Release Date
Close