Synth modules

Notes: This is a new revision of one of ADDAC's first modules, back from 2010.

Now more compact in 6hp and with an Offset CV input.

The incoming signal amplitude is controlled by a [GAIN] attenuverter circuit allowing to attenuate the signal as well as invert its phase.
A back jumper can set the maximum gain amount to either x1 (unity gain) or x10. DIY modifications can be made by changing its resistors.
After the Gain an offset can be added to the signal, displacing the signal up or down (-5V to +5V) this can be adjusted using the [OFFSET] knob and CV input

When using no input using the [OFFSET] knob and CV input will generate an output between -5V and +5V.

Tech Specs:

6HP
2.5 cm deep
40mA +12V
40mA -12V

Notes: A Comparator is an electronic circuit that compares two voltages and switches its output to indicate which is larger. The Comparator operates between -10 or +10V

The Output is always -10V if below Threshold and +10V if above Threshold.

A Rectifier is an electronic circuit that is used to transform AC signals to an equivalent DC signal while removing one of it's polarities, i.e. Positive rectification excludes negative signals and vice-versa.
Both sections can be used to change the shape of any waveform as well as its harmonic content.

FRONTPANEL:
1 Comparator Threshold Knob
1 Comparator Jack Output
2 Comparator Monitor Led1 Common Signal Jack Input
4 Rectificated Outputs

MECHANICAL:
Format: Eurorack
Width: 4 HP
Depth: 2.5 cm

CONTROL VOLTAGE I/O:
CV inputs: i 10v
CV outputs: i10v

ELECTRICAL:
Max current: 30mA
Compatible with +-12v and +-15v power supplies
Bus Board Cable: 8 × 2 IDC (Doepfer style) connector

Notes: The ADDAC213B is the second pair of modules from ADDAC's Eurorack Bridge system.

A pair of ADDAC213Bs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.

Two ADDAC213B modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clatter, less spaghetti- more space of your fingers on those knobs!

ADDAC213Bs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time. The modules can be installed in normal position or a 180 degree position to fit any need.

As an Expansion to an ADDAC213A.

Each ADDAC213B connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.

Up to 2 ADDAC213B can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.

If you're looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A.

Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!

Each module can be installed in normal position or at 180 degrees.

Comes with a 50cm ribbon cable. Custom sizes are available upon request.

Mechanical:
. Format: Eurorack
. Width: 3 HP
. Depth: 2.5 cm

Electrical:
Passive / Does not draw current
Ribbon Cable: 50cm or 100cm ribbon cable

Notes: Following ADDAC System's T-Networks series, the importance of having the right input signal for firing drum modules or envelopes was realised. Gates and Triggers are often looked at as similar signals but at times it really makes a difference and results will change drastically depending if a Gate or a Trigger is fed to the input of such modules.

This led to the simple yet effective Gate to Trigger.
A four channel converter with bypass switch for each channel.

Any input Gate will be limited to a 1ms Trigger.

Tech Specs:
3HP
2.5 cm deep
10mA +12V
10mA -12V

Notes: Passive dual expression pedal attenuator.

Plug any CV or audio source through it and control its amplitude through any standard expression pedal.

Invert switch for inverting the expression pedal action.

Specs:
- Passive Module
- Width: 4 HP
- Depth: 3 cm

Notes: ADDAC309 CV to Expression allows a simple and straight forward connection between modular and effect pedals that features expression pedal TRS inputs.

Instead of using an expression pedal into the effects pedal the user can use this module in between a CV source and the Effects pedal to be controlled.

This is a great way to control the available parameters on the effects pedals straight from a CV source.

ADDAC309 features 2 channels each with a CV Input with attenuator and a 1/4" jack output.

This is a passive module, the power needed for operation is taken from the pedal power instead of the modular frame, this allows for perfect matching of the pedal's operating voltage which can range from 3.3v to 9v.

Tech Specs:
4HP
3,5cm deep
Passive module

Notes: Dedicated expansion for the ADDAC807C VC Summing Mixer

Features 4 individual track post fader stereo outputs.

2Hp
2 cm deep
0mA