100% Compra Segura

Studio equipment

Our full range of studio equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.

Visit Juno Studio

100% Compra Segura

DJ equipment

Our full range of DJ equipment from all the leading equipment and software brands. Guaranteed fast delivery and low prices.Visit Juno DJ

View:
Options
Artículos del 1 al 38 de 38 en la página 1 de 1
Notes: Incredibly powerful two-channel filter module capable of much more than just filtering. State-variable digital filters with built-in VCAs designed to overdrive beautifully. Sounds great.

Supplier's notes:
BIONIC LESTER MARK III is a 2-channel 2-pole state-variable digital filter with an unusual amount of good sonic character. The filter mode is continuously variable under manual or CV control, smoothly fading from lowpass to bandpass to highpass to notch to allpass with a single motion. The resonance stops just short of self-oscillation. A digital VCA controls the amplitude and the distortion of the input signal pre-filter. The filters have independent inputs and outputs, and an additional Mix output with balance control. The filter design was initially inspired by the best of late-1990s "virtual analog" filters and has gone far beyond.

The audio input controls have dual behavior. When the control (or CV input) is turned from zero position to the center, it operates as a simple gain control for that input. When turned past the center position towards the maximum, the signal will begin to soft-clip, adding hard clipping as the maximum is approached. This smooth and subtle distortion adds violence to otherwise unremarkable input material, generating additional harmonic content for the filter to process. The digital VCA that controls the gain and distortion functions is aware of the input signal's zero crossing, eliminating "clicking" noises when the gain is modulated.

Each filter section has three CV inputs. The first is a high-speed input hardwired to the filter's cutoff frequency, appropriate for snappy envelopes and slow moving voltages alike. The other two inputs (one with attenuverter control) are freely assignable to any of the filter parameters (cutoff, resonance, mode, gain), storable in a preset. The Mark III preset system stores eight fully programmed panel setups, instantly recalling everything under the harshest demands of performance. The Morph mode allows smooth fading between all of these presets.

Activate Filter B's LINK control for patch-free routing of the filter's control or audio signal. You can achieve dual-peak resonance, cable-free series routing, cascaded 4-pole filtering (with two stages of distortion), and full stereo using only one set of filter controls. The input normalization, LINK settings, and parallel mix output further reduce cable clutter while rapidly patching an elaborate signal flow.

The controls are arranged for maximum tweakability and minimum cable interference, with metal-shaft potentiometers attached to the panel on the large knobs. The Mark III OLED display displays the cutoff frequency in Hertz, resonance amount, and filter type morph. The CV inputs process all input voltages between -10 to +10 volts. Panel size is 15HP.
Read more
 5 in stock $474.19
Click for better price!
or call +44 20 7424 1960
quote 742141
Cat: 739128 Rel: 04 Nov 19
 
Expanded take on Mutable Instruments' famous Clouds granular texture synthesiser - grey faceplate, 34HP
Notes: Serious granular synth power in this expanded reissue of the classic Mutable Instruments Clouds module. Easier to use and more powerful than the original. Ultra creative approach to unique synth textures

Supplier's notes:
Clouds, the granular synthesis module from Mutable Instruments, was discontinued in 2017. Supercell brings back Clouds in a more accessible 34 hp form factor, offering an improved user interface and several additional features:

- Each of the Blend parameters (Feedback, Panning, Mix, and Space) have dedicated knobs with their own CV inputs and inverting attenuators (attenuverters).

- The inputs and outputs now have mute switches, stereo VCAs, and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- A stereo output gain control has been added, providing an additional +6 dB of gain to compensate for low output levels when using certain parameter combinations.

- The complex process of changing the sampling time and managing presets has been simplified with dedicated switches and status LEDs.

- Extensive modulation options for all parameters including direct patching of external CV, distribution of one CV to all parameters via the AUX input, or an internal smooth random CV that is normalized to any unpatched inputs when AUX is also unpatched. The attenuverters control the modulation depth in all three cases. As of firmware v1.01 the internal modulation rate can be adjusted within a range of 1 to 100 Hz.

- The inputs and outputs now include stereo VCAs and separate VU meters. The knobs act as offset controls when their respective VCA inputs are patched.

- Pitch is now controlled by two separate inputs: the V/Oct input is exponential and the Pitch input is linear. When both inputs are used, their voltages are summed.

- A manual Trig switch (for capturing individual grains) has been added, in addition to the Trig input that was present on Clouds.

All other features of the original Clouds remain intact, including access to the alternate modes. Thanks to Olivier Gillet for making the original Clouds hardware and firmware available under open-source licenses. Third-party firmware such as Parasites (by Matthias Puech) and Beat Repeat (by Julius Kammerl) will be supported in future firmware updates after the initial release of the module.
Read more
 3 in stock $464.51
Click for better price!
or call +44 20 7424 1960
quote 739128
Cat: 749524 Rel: 16 Oct 19
 
Compact modular system with full analogue design - Eurorack version
Notes: Pico System III brings modular synthesis back to the basics - the system has multi functional (instead of single-function, like Pico Drums or Pico Trigger in the Pico System II) analogue modules and is intended to encourage creativity in modular patching.

The system has 31 inputs and 20 outputs (master output is duplicated) + 7 switches; if you have enough patch cables at your disposal, you can patch the system in 121000931215044250740178662400 or 1.21x1029 variations (we ignored the possibility to adjust potentiometers here). Even though only 0,0001% of all patches will sound more-less enjoyable, you and all your future generations can spend a lifetime only patching the Pico System III.

Voice-cards with preset patches set it apart from other eurorack systems - they allow user to change patches instantly and radically, which makes the system well suited for experimental live performances. The system comes with 5 great sounding "factory preset" voicecards, and 5 DIY voicecards that are empty and users can develop their own patches. More voicecards will be available from the Erica Synths shop.

Eurorack module includes: 1 Hosa stackable cable, ribbon power cable, 5 factory preset & 5 DIY voice-cards, user manual and patch note sheets.
Read more
 3 in stock $448.37
Click for better price!
or call +44 20 7424 1960
quote 749524
Cat: 749818 Rel: 05 Nov 19
 
Analogue dual overdrive filter module
Notes: The Ar Merc'het Brao module is comprised of two filters and two overdrives.

As usual at Touellskouarn it has a Breton name: Ar Merc'het Brao means "The pretty girls".

It can be used with a stereo signal or with two mono signals. The module is modular as well as guitar friendly.

The filters are resonant with a slope of -12dB. A switch allows to switch each filter from LowPass to HighPass. The filter cut-offs are voltage controlled thanks to dedicated CV inputs. Additionally, the Ar Merc'het Brao features global controls for cut-off and resonance.

Both overdrive sections offer the classic and well known TouellSkouarn distortion sound.
Read more
 2 in stock $361.28
Click for better price!
or call +44 20 7424 1960
quote 749818
Cat: 752820 Rel: 17 Oct 19
 
Comb oscillator, VOSIM, summation synthesis & phase modulation with adjustible waveform & wave folder
Notes: Loquelic Iteritas is a digital VCO with interpretations of three classic synthesis algorithms involving dual pitch control. It creates a huge variety of sounds parameterized by four tone and two pitch controls.

It has had glowing reviews from Surgeon and Surachai, and I am personally very excited about this module!

It has a simple interface, with 3 different synthesis algorithms allied to a number of different controls / CV inputs which have different effects, depending on which mode you choose. Simply hook up a number of modulation sources to the 4 inputs and start wiggling!

Rev.2 now features an additional sync input.

Size: 10HP Eurorack
Depth: 1.5 Inches
Power: 2x8 Eurorack
Draw +12V: 150 / 80
Draw -12: 5 / 5
Draw +5v: 0 / 90
Read more
 1 in stock $352.67
Click for better price!
or call +44 20 7424 1960
quote 752820
Cat: 739915 Rel: 24 Oct 19
 
Full voltage-controlled instrument interface
Notes: Interesting MIDI option for Eurorack. Eight faders and buttons, mappable to MIDI note, CC and lots more parameters, then controllable using CV and gate signals. Versatile.

Supplier's notes:
A fully editable MIDI controller with eight faders and push buttons. Each of them with a CV or Gate input associated to automate their functioning via external signals or to be configured independently for further control.

Each control on VCMC can be edited on its OLED screen and will be output either via DIN-5 or USB as a class compliant MIDI device.

- Current needs: +12V: 64mA, -12V: 12mA
- Width: 20 HP
- Depth: 30 mm
- Aluminium, heat-treated front panel
Read more
MRP:$411.61 SAVE 22%
 8 in stock $321.50
Click for better price!
or call +44 20 7424 1960
quote 739915
Cat: 754307 Rel: 28 Oct 19
 
Quad voltage controlled filter module
Notes: Tone is a quad, voltage controlled filter with low pass and band pass outputs. Its four channel architecture enables the intuitive patching of shimmering, polyphonic textures. The 24dB slope provides a warm, buttery character. Self oscillation allows each channel to double as a sine wave oscillator with v/oct tracking across four octaves. Cascade OTA topology. A perfect match for the Chord.
Read more
 1 in stock $283.87
Click for better price!
or call +44 20 7424 1960
quote 754307
Cat: 751766 Rel: 23 Oct 19
 
DSP based effects module - 18HP
Notes: Module A-187-1 is a DSP based effects module. Four parameters of the selected digital effect are voltage controlled. The main effect (e.g. reverb, delay, pitch-shifter, equalizer) is selected by the two small buttons effect up/down. The upper row of the display shows the effect that is currently selected. In the lower row the four parameters are shown as well as a small bar left from the abbreviation that displays the current parameter value. Each parameter can be adjusted manually (upper potentiometer row) and modified by external control voltages (lower row of the potentiometers and upper row of the sockets). The lower row of the sockets contains the two audio inputs and outputs.

Another button (bypass) is used to turn the effect on/off. When bypass is chosen the upper line of the display shows in turn "BYPASS" and the name of the pre-selected effect. In the bypass mode another effect can be pre-selected and called-up by pressing the bypass button again. Even the effect parameters can be adjusted and are displayed with the bar graphs. But they become effective not before the bypass mode is left.

The module is equipped with two audio inputs and two audio outputs because the DSP board features stereo audio processing. The audio inputs can process usual A-100 signal levels without clipping/distortion. For higher levels external attenuators (e.g. A-183-1) or VCAs may be used.

A ready-made DSP board is used inside the A-187-1 module. Consequently, only these effects and parameters are available that are supported by the DSP module. Some parameters can be changed only in steps or with audible artefacts. The DSP board has 20 Bit DA and AD converter with 32 kHz sample rate available. The inter sound processing uses 24 Bit.
Read more
 1 in stock $261.29
Click for better price!
or call +44 20 7424 1960
quote 751766
Cat: 734884 Rel: 15 Oct 19
 
6HP VCO with auto-tuning & octave shift
Notes: Simplified version of the Furthrrrr Generator dual VCO, inspired by Don Buchla's designs. Through-zero linear FM, wavefolding, sub-oscillator and auto tuning. Proper west coast synthesis at its best.

Supplier's notes:
The Endorphin.es Godspeed is sort of the single oscillator version of the famous Furthrrr Generator. From its big brother it takes over the digital Thru-Zero core and the legendary wavefolder. But it also has new features like a sub-oscillator output and an immensely practical autotune function.

Especially for people starting with a modular system this oscillator is highly recommended. On 6HP it delivers all the features (and more) needed for diving into the depths of West-Coast-Synthesis!
Read more
 6 in stock $252.67
Click for better price!
or call +44 20 7424 1960
quote 734884
Cat: 755446 Rel: 07 Nov 19
 
Precision voltages module - dark edition
Notes: Sometimes real precision is required with pitch control voltages - this module features a super accurate "Cal" output, which is accurate to <1mV over 20V, translates to one cent over 20 octaves! It is ideal for calibrating the scaling of VCO's, indeed we have been using our own version of this circuit to calibrate our own MiniMod VCO's for the last three years.

As well as being a precision voltage source it is also a very accurate voltage adder, it has two channels (A & B) and both full volts (octaves) or 1/12th volt increments (notes) can be either added to or subtracted from the incoming signal. Perfect for adding a voltage offset to the output of a sequencer or it can be used to add switchable octaves to a VCO which only has course and fine tunes controls.

It also has a "mix" output, which allows either A channel on its own, or with the three way toggle switch channel B can either be added to, or subtracted from channel B, and this is in addition to the addition and subtraction per channel mentioned earlier.

Dimensions: 10HP wide, 26mm Deep
Read more
 3 in stock $232.25
Click for better price!
or call +44 20 7424 1960
quote 755446
Cat: 749081 Rel: 25 Oct 19
 
Eurorack instrument interface with Neutrik combo connector - 8HP
Notes: Instrument Interface is a Eurorack pre-amp capable of bringing any type of audio signal to modular levels, thanks to its amplification circuit.

The module can drive regular and condenser microphones (+48V Phantom Powered), as well as Instrument and Line signals with a very low distortion ratio.

Going further from the regular re-amp operation, Instrument Interface offers some additional extra functions like a Trig/Gate extractor and Envelope Follower circuits, allowing you to use the character of your audio signal in more creative ways.
Read more
MRP:$282.58 SAVE 22%
 7 in stock $220.43
Click for better price!
or call +44 20 7424 1960
quote 749081
Cat: 749823 Rel: 05 Nov 19
 
Dual channel stereo panner with automation
Notes: The FLAME "PANMIX" module contains two independent panning mixers with one input each on two outputs left/right and is designed for audio or CV sources in the voltage range +-5v (audio modular level). In addition, the 2 inputs can be switched separately to +6db audio (for external audio line level sources) using the slide switch on the rear panel.

The movements of the two mix controls can be recorded. The recording time per channel is more than one minute. The playback speed can be adjusted in playback. The recorded track is played back once when the Play button is pressed briefly (one shot) or in the loop when the button is pressed a little longer.

Both panning channels have a separate reset input as well as a separate CV input (+-5V ) for controlling the mix e.g. by an LFO. The track data remains permanently stored (battery buffered memory).

In addition, there are three further audio/CV signal inputs (a mono and stereo left+right), which are routed directly to the output and mixed together with the two PAN channels. This allows you to mix in other sources directly and e.g. connect two or more "PANMIX" modules together.
Read more
 1 in stock $189.24
Click for better price!
or call +44 20 7424 1960
quote 749823
Cat: 753566 Rel: 07 Nov 19
 
Full wave rectifier & distortion - 8HP
Notes: Pura Ruina is a three-stage CV-controlled fully-hyphenated full-wave rectifier/distortion designed for audio. Simple waveforms can be manipulated into completely new and exciting tones, and already complex sounds can be shredded into sonic oblivion. Add some CV and you'll never want to let PR out of your rack!

Each stage has an individual level control with corresponding CV and individual out, as well as feeding to the universal Sum output. PR's rectification creates a unique flavour of distortion unlike standard wavefolding or clipping. The possibilities are virtually endless: add to a west-coast style complex oscillator setup for unique timbral shaping, annihilate a percussion mix through it, run its individual outs through other Ruina modules for further mayhem... You'll never run out of awesome things to try.
Read more
 2 in stock $187.08
Click for better price!
or call +44 20 7424 1960
quote 753566
Cat: 734886 Rel: 15 Oct 19
 
Stereo filter with voltage controlled resonance - 6HP
Notes: Versatile stereo digital filter based on Endorphin's Grand Terminal module. CV-controlled cutoff, resonance and separate high-pass filter. Simple but effective.

Supplier notes:
The Squawk Dirty To Me is a stereo filter with voltage controlled resonance. It features eight filter modes and zero-delay feedback.

- Simple and effective 6hp stereo VCF
- 8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters
- Additional hi-pass filter in series quickly cuts the boomy low end
Read more
 4 in stock $179.56
Click for better price!
or call +44 20 7424 1960
quote 734886
Cat: 734890 Rel: 15 Oct 19
 
Multi effects module - 6HP
Notes: Milky Way is a multi effects module with stereo signal flow. Its algorithms are already known from the Blck_Noir and the Grand Terminal.

- Simple and effective 6hp stereo* FX module
- Comes with "T.F.D" firmware installed: 16 types of effects are available, sorted in two banks
- Meta CV effects scanning
- Volume control with VCA

*depending on the effect type
Read more
 3 in stock $179.56
Click for better price!
or call +44 20 7424 1960
quote 734890
Cat: 734888 Rel: 22 Oct 19
 
6HP function generator
Notes: Airstreamer is a function generator with AD, ASR and loop mode. The curves can be altered in shape. A 1V/octave input makes it possible to play the module like an oscillator.

- Fast and effective envelope generator with variable slope curves and three modes: looping, attack-sustain-release (ASR) and attack-decay (AD)
- 320 khz samplerate, zero aliasing CV generation
- 1v/oct input, bipolar and unipolar outputs, selectable end of cycle outputs
- Thru-zero VCA input that inverts the envelope when CV goes to negative voltages
Read more
 2 in stock $150.52
Click for better price!
or call +44 20 7424 1960
quote 734888
Cat: 749089 Rel: 24 Oct 19
 
Dual pre-amplifier module - 4HP
Notes: Inamp is a dual pre-amp in just 4 HPs. Featuring 6,3 Jacks inputs as well as Minijacks.

Both inputs are summed so you can use them at the same time as an input mixer.

The unit is designed to amplify up to x20 the input signal, allowing to amplify most of the music machines out there (Domestic line levels) as well as some guitars (Humbucker-like pickups and so).

The first channel is normalled to second one in series, so it's possible to have two stages of amplification or two separate ones.
Read more
MRP:$174.19 SAVE 17%
 5 in stock $145.16
Click for better price!
or call +44 20 7424 1960
quote 749089
Cat: 751704 Rel: 23 Oct 19
 
Slew processor/generator - 8HP
Notes: Module A-171-2 is a voltage controlled slew limiter with a lot of additional features beyond a simple slew limiter. It's mostly a licensed copy of Ken Stones VCS which is in turn based on the Serge VCS.

Typical applications:

- VC Slew Limiter / VC Portamento / VC Low Pass Gate:

Cycle switch = off, no trigger signal applied to Trig socket: Voltage controlled Slew limiter or portamento generator: the signal applied to the signal input is "slewed". The slew up and down times are controlled manually by means of the Up and Down controls, the effect of the CV Up and CV Down control voltages are controlled by the CV Up and CV Down controls, in exponential mode these controls also affect the slew shape (see symbols at the CCW and CW positions of the controls).

If an audio signal is applied an short slew rates are chosen the module works as a simple VCF/VCA combo.

- A/D Envelope Generator / Pulse Delay / Subharmonic Generator:

Cycle switch = off, trigger signal applied to Trig socket, no input signal: Simple Attack/Decay envelope Generator, the rise and fall times are controlled like the slew up/down times above, including the shape of the falling/rising slope of the envelope, the exp. CV input can be used to change both attack and decay simultaneously.

At the End output a pulse appears as the end of the envelope is reached (less than about 20mV), this can be used as a pulse delay.

If a series of triggers are applied to the VCS faster than the total rise and fall times, the module will divide the incoming signal by a whole number. In the audio range the output will be the sub-harmonic series.

- VCLFO / VCO:

Cycle switch = on, no trigger signal applied to Trig socket, no input signal: Voltage controlled LFO/VCO, the rise and fall times of the waveform are controlled like the slew up/down times above, including the shape of the falling/rising slope
the exp. CV input can be used like the CV input of a VCO or VCLFO, the response is exponential but not exactly 1V/oct.
Read more
 1 in stock $131.17
Click for better price!
or call +44 20 7424 1960
quote 751704
Cat: 577809 Rel: 23 Oct 19
 
Slew processor/generator - 8HP
Notes: Module A-171-2 is a voltage controlled slew limiter with a lot of additional features beyond a simple slew limiter. It's mostly a licensed copy of Ken Stones VCS which is in turn based on the Serge VCS.

Typical applications:

- VC Slew Limiter / VC Portamento / VC Low Pass Gate:

Cycle switch = off, no trigger signal applied to Trig socket: Voltage controlled Slew limiter or portamento generator: the signal applied to the signal input is "slewed". The slew up and down times are controlled manually by means of the Up and Down controls, the effect of the CV Up and CV Down control voltages are controlled by the CV Up and CV Down controls, in exponential mode these controls also affect the slew shape (see symbols at the CCW and CW positions of the controls).

If an audio signal is applied an short slew rates are chosen the module works as a simple VCF/VCA combo.

- A/D Envelope Generator / Pulse Delay / Subharmonic Generator:

Cycle switch = off, trigger signal applied to Trig socket, no input signal: Simple Attack/Decay envelope Generator, the rise and fall times are controlled like the slew up/down times above, including the shape of the falling/rising slope of the envelope, the exp. CV input can be used to change both attack and decay simultaneously.

At the End output a pulse appears as the end of the envelope is reached (less than about 20mV), this can be used as a pulse delay.

If a series of triggers are applied to the VCS faster than the total rise and fall times, the module will divide the incoming signal by a whole number. In the audio range the output will be the sub-harmonic series.

- VCLFO / VCO:

Cycle switch = on, no trigger signal applied to Trig socket, no input signal: Voltage controlled LFO/VCO, the rise and fall times of the waveform are controlled like the slew up/down times above, including the shape of the falling/rising slope
the exp. CV input can be used like the CV input of a VCO or VCLFO, the response is exponential but not exactly 1V/oct.
Read more
 1 in stock $115.04
Click for better price!
or call +44 20 7424 1960
quote 577809
Cat: 734891 Rel: 15 Oct 19
 
Portable 2HP power module for compact skiff cases with dual passive mults
Notes: The power module from Endorphin.es is a module for the power supply of smaller modular systems such as skiff cases up to 104 TE width. The module consumes DC power between 12 and 20 volts from an external power supply unit. Voltages of up to +1000 mA and -700 mA are output, also depending on how strong the connected power supply is. In addition, there are two passive multiples.
Read more
 1 in stock $112.89
Click for better price!
or call +44 20 7424 1960
quote 734891
Cat: 751757 Rel: 23 Oct 19
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
 1 in stock $106.44
Click for better price!
or call +44 20 7424 1960
quote 751757
Cat: 747513 Rel: 07 Nov 19
 
Two high quality & precise linear VCA's - 8HP
Notes: The Voltage Controlled Amplifier or "VCA" is one of the most essential and useful building blocks in a synthesis patch. The DUAL VCA 1U packs two high quality, DC coupled, linear VCAs into a very compact 1U package.

The two VCAs can be used completely independently or in tandem via the handy signal normalling. The DC coupling means that the VCA can be used for the amplitude control of both control voltages (CV) and audio signals.

Some application/use examples:

- Dual, independent VCA for dynamic level control of two different audio or cv sources
- Stereo VCA (use the CV normalling where CV A normals to CV B) for processing stereo sources or CV pairs.
- CV/Audio summing (when Out A is not patched, it normals to sum with OUT B, CV A and B control the independent levels)
- Voltage/signal doubling (use input A only and the doubled voltage will appear at OUT B when a CV of +5V applied to CV A)
Read more
 5 in stock $104.30
Click for better price!
or call +44 20 7424 1960
quote 747513
Cat: 751756 Rel: 23 Oct 19
 
4HP Eurorack module featuring a combination of 3 functions
Notes: Module A-184-1 is the combination of three functions:

- Ring Modulator
- Sample&Hold/Track&Hold unit
- Slew Limiter

The same functions are actually already available in other modules (e.g. A-114, A-148, A-170). But in many systems it's not necessary to have two ring modulators (A-114) or two S&H units (A-148) or two slew limiters (A-170) available. That's why we have compiled these function in one small 4 HP module.

The upper section is nothing but half of an A-114, i.e. a ring modulator with the usual X/Y inputs and the X*Y output. Inputs and outputs of this sub-unit are AC coupled, i.e. suitable only for audio signals. A detailed explanation of a ring modulator can be found on the A-114 info page.

The lower section is a Sample & Hold (S&H) / Track & Hold (T&H) unit (same as half of an A-148) followed by a slew limiter (same as the upper section the A-170). A toggle switch is used to set the mode to S&H or T&H. In S&H mode the unit picks out a sample from the voltage at the SH input at the rising edge of the trigger signal input. In T&H mode the output follows the input voltage as long as the level of the trigger signal is high. As soon as the trigger signal turns low, the last voltage is stored. The trigger input is internally normalled to high, i.e. the unit works just as a slew limiter in T&H mode when no trigger signal is applied.
Read more
 1 in stock $96.76
Click for better price!
or call +44 20 7424 1960
quote 751756
Cat: 751716 Rel: 23 Oct 19
 
Theremin controller module - 8HP
Notes: Theremin module for generating a variable control voltage by approaching/removing hand to/from an antenna. The distance range is about 30-40 cm. Additionally the module is equipped with a Gate output with adjustable threshold level. Controls/Inputs/Outputs: antenna input, offset (knob for zero adjust), 2 x CV out, 2 x LED (for CV control positive/negative and zero offset adjust).

To simulate the original Theremin two A-178, a VCO (e.g. A-110) and a linear VCA (e.g. A-130 or A-132) are required. But of course the A-178 can be used to control other functions in the A-100 (e.g. filter frequency, modulation depth and/or speed, tempo, attack/decay time and so on).

The CV output voltage of the A-178 can range - according to the setting of the front panel controls - from -10V...+10V. The gate output switches from 0V to about +10V.

Applications:

- Controlling any voltage controlled parameter of the A-100, e.g. pitch or pulsewidth (VCO A-110), loudness (VCA A-130/131/132), panorama (A-134), filter frequency or resonance (A-120/121/122/123), phasing (A-125), frequency shift (A-126), resonance peaks (A-127), envelope parameters (A-141/142), tempo (A-147)

- Triggering of A-100 activities via gate with adjustable threshold, e.g. starting an envelope (A-140/141/142), Start/Stop of a sequence (A-155), any switching function (A-150/151)

- Conversion into MIDI control change messages is possible with the A-192.

If two or more A-178 are used the distance between the modules/antennas should be at least 40-50 cm. Otherwise the antennas may affect each other.
Read more
 2 in stock $96.76
Click for better price!
or call +44 20 7424 1960
quote 751716
Cat: 751758 Rel: 23 Oct 19
 
Sine converter/VC crossfader - 4HP
Notes: Module A-184-2 is the combination of two functions and planned primarily as an expansion module for VCOs or LFOs (e.g. A-110-1, A-110-2, A-145, A-147-2).

Triangle-to-Sine Waveshaper:

The upper section is a very precise triangle-to-sine converter (thanks to Tim Stinchcombe who recommended this circuit). It can be used to convert any triangle waveform into a (nearly) perfect sine. The converter is much better than the simple diode converter used in the A-110-1, A-111-1, A-145 and A-147-2. Two trimming potentiometers are used to optimize the sine shape. The converter should be assigned to one VCO or LFO because the trimming potentiometers have to be re-adjusted if the input level or DC offset of the input signal changes. If the trimming potentiometers are deliberately mis-adjusted it can be used also as a waveshaper for non-sine waveforms (e.g. sine-shaped at the top of the signal and a peak at the bottom, even voltage controlled by applying an additional voltage to the waveshaping circuit, "circuit-bending" notes will be available).

The waveform converter is DC coupled and can be used also for low frequencies (e.g. LFO triangle waves).

Voltage Controlled Crossfader:

The lower section is a voltage controlled crossfader. It has two inputs A and B. The two signals are mixed together with variable percentage. When the manual control CF is fully CCW only signal A appears at the CF Out socket. When the manual control CF is fully CW only signal B appears at the CF Out socket. In the centre position of the manual control both signal appear with the same level. In addition a control voltage input CV with attenuator is available to enable voltage control of the crossfade.

Two LEDs display the crossfading shares of input A and B.

The crossfader uses two high quality VCAs (SSM2164). Inputs and outputs are DC coupled. Consequently it can be used for audio signals and slowly varying control voltages as well.

The sockets of the upper section (triangle and sine) are normalled to the inputs A and B of the crossfader section. That way the crossfader is used to fade between triangle and sine of the VCO or LFO connected to the waveshaper. If other signals are plugged into the input sockets A and B these signals are used for crossfading.

The main application is to fade between two different waveforms of a VCO or LFO or two different VCF outputs. But the module can be used for any other signals too as the waveshaper and crossfader sections are independent apart from the normalled sockets.
Read more
 1 in stock $81.18
Click for better price!
or call +44 20 7424 1960
quote 751758
Cat: 751707 Rel: 23 Oct 19
 
Modulation wheel module with two wheels - 14HP
Notes: A-174-2 is a modulation wheel module with two wheels. The factory setting is a spring loaded wheel at the left side with bipolar voltage output (i.e. 0V in centre position, positive voltage in the upper range, negative voltage in the lower range, voltage range about -5.5 V ... 0V ... +5.5 V) and a wheel without spring at the right side with positive voltage output (i.e. 0V in the lowest position and positive voltage when operated, voltage range about 0...+8 V). For the spring loaded wheel a voltage "plateau" around 0 V is preset (jumper) so that the output voltage is 0 V in a small area near the centre position.

By means of jumpers the factory settings can be changed. For each wheel two jumpers are available: one for the voltage range (positive or bipolar) and one for the voltage plateau around 0 V. If these settings are changed even the wheels have to be re-adjusted mechanically. Therefore, such modifications should be carried out by a qualified person only. By request the module is available from the factory even with two wheels both with or without springs (additional charges Euro 10.00 for each change).

Important note for module mounting: As the potentiometer of the left wheel projects about 10 mm the rim of the front panel a 2 or 4 HP blind panel has to be mounted left from the module - unless the module left to the A-174-1 has sufficient space in this area (e.g. A-174-1).
Read more
 2 in stock $77.42
Click for better price!
or call +44 20 7424 1960
quote 751707
Cat: 751702 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
 1 in stock $77.42
Click for better price!
or call +44 20 7424 1960
quote 751702
Cat: 751764 Rel: 23 Oct 19
 
Precision adder (mixer) and buffer for control voltages - 6HP
Notes: Module A-185-2 is a precision control voltage adder/buffer. Precision means that the amplification of the inputs without attenuators is exactly 1.00 and is suitable to add control voltages for the pitch control of VCOs (e.g. from keyboard + sequencer 1 + sequencer 2). Summing resistors matched to 0.1% are used to obtain an accuracy of 0.1% for the added voltages.

The module is equipped with four CV inputs: one with attenuator and three without attenuator. Each input is normalled to +1 V (i.e. if no plug is inserted the input contributes 1 V to the sum appearing at the output).

The input with attenuator can be used for common modulations (e.g. from an LFO, ADSR, Theremin, Pitch-Bender) for all VCOs connected to the output. The Lev.1 control is used to adjust the depth of the modulation, the first switch selects the polarity of the modulation. If no signal is connected to the first socket the attenuator works as a (fine) tuning knob because a voltage in the range 0...+1V (right position of the switch) or 0...-1V (left position of the switch) is added to the CV output.

The inputs without attenuators are planned to add control voltages coming out of keyboards, sequencers, Midi-to-CV interfaces, ribbon controllers or other CV sources that follow the 1V/oct standard. For example the CV of a keyboard can be used to transpose the CV coming from a sequencer, or the CV of a slow sequencer can be used to transpose the CV from a fast sequencer.

Each input is equipped with a three-position switch that determines if the corresponding voltage is added (right position), subtracted (left position) or if the input has no effect (centre position). If no plug is inserted the corresponding switch works as an octave switch for the lower three sections as the default 1 V are added or subtracted to the output voltage according to the switch position. The first switch can be used to add a variable voltage to the sum output. The variable voltage is adjusted with the Lev.1 control and the knob works then as kind of a (fine) tuning control.

The module is equipped with 4 outputs: three non-inverting and one inverting ouput. An internal jumper can be used to connect the non-inverted or inverted output to the CV line of the A-100 bus. That way the module can used to control several VCOs that are connected to the same bus board as the A-185-2 (same functionality as A-185-1).
Read more
 1 in stock $76.33
Click for better price!
or call +44 20 7424 1960
quote 751764
Cat: 752435 Rel: 25 Oct 19
 
Small passive expander for the Listen Four & Listen IO modules - 4HP
Notes: The Listen Up is a small passive expander for the Listen modules that provides stereo 1/4" (6.35mm) jack inputs and outputs. It connects to one or two Listen modules and/or WAV Recorder module with the included 3-pin cables. There are four 1/4" jacks arranged in left/right pairs. The left jack of each pair can be used as a TRS stereo jack if the right jack is unpatched.
Read more
 3 in stock $65.58
Click for better price!
or call +44 20 7424 1960
quote 752435
Cat: 751699 Rel: 23 Oct 19
 
Two separate slew limiters for generating portamento effects - 8HP
Notes: Module A-170 contains two separate slew limiters, also known as portamento controllers or integrators. The first SL has just one joint control, which sets both rise and fall times (c. 0 ...10 sec). The second SL has separate controls for rise and fall times, and can therefore be used as a simple AR envelope generator. Over and above this, you can set the overall range for these parameters, with a three-position switch, as on the full ADSRs.

Both slew limiters have two LEDs each, to show the state of the rising and falling voltages.


Additional technical remarks: If the upper slew limiter is used for precision applications (e.g. portamento/glide of one or more VCOs) a buffer (e.g. A-185-1 or A-185-2) is recommended between the A-170 output and the VCO(s) input(s). The reason is a small voltage drop that is caused by the protection resistor at the A-170 output. An A-185-1 or A-185-2 connected between the A-170 and the VCO(s) avoids that voltage loss. For all A-170 manufactured later than May 2009 (recognizable by the label "Version 2" on the pc board) this remark is not valid as these modules are equipped with an additional voltage buffer at the output.

The lower slew limiter cannot be used for precision applications because of the voltage loss caused by the diodes of the circuit.
Read more
 1 in stock $63.43
Click for better price!
or call +44 20 7424 1960
quote 751699
Cat: 751709 Rel: 23 Oct 19
 
Two identical inverters - 4HP
Notes: Module A-175 (Dual Voltage Inverter) is exactly what it says it is: two identical inverters, which will take a voltage and output it in an inverted form - so that an input of +5 V will be output as -5 V, an input of -2 V will be output as +2 V, and so on. Two LEDs give a visual indication of the (positive or negative) output signal.
Read more
 1 in stock $52.69
Click for better price!
or call +44 20 7424 1960
quote 751709
Cat: 751722 Rel: 23 Oct 19
 
Two multiples with one 1/4 jack socket & two 3.5mm jack sockets each
Notes: Doepfer's A-181 Multiples 2 is a simple multiple and cable format converter, suitable for translating 1/4" signals to 1/8" and vice versa. The upper mult is wired for monophonic signals, while the lower mult features a 1/4" stereo connector which offers direct 1/8" connection to the tip and ring, respectively, allowing use as a stereo splitter or dual 1/8" to stereo 1/4" converter.
Read more
 1 in stock $52.42
Click for better price!
or call +44 20 7424 1960
quote 751722
Cat: 751706 Rel: 23 Oct 19
 
Module for processing/mixing of control voltages - 4HP
Notes: A-172 is a minimum/maximum selector module and is equipped with four analogue inputs and two analogue outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar, but even for audio signal processing the module can be used (e.g. several outputs of the same or different VCOs).

The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

To adjust offset and amplitude for each input independently (i.e. to bring the signal into the right "position" with the desired level) we recommend combining the module with the A-129-3 Slew Limiter/Attenuator/Offset Generator (see patch example below). The other sketch below shows the basic principle of the max/min module by means of three sine waves (e.g. three LFOs) with different frequencies and different levels.

The module can be used also as a simple half-wave rectifier.
Read more
 1 in stock $50.53
Click for better price!
or call +44 20 7424 1960
quote 751706
Cat: 751720 Rel: 23 Oct 19
 
Dual buffered 1-in-3 multiple module - 4HP
Notes: Module A-180-3 is a dual buffered 1-in-3 multiple. The signal applied to the input socket appears as a buffered signal at the three output sockets. Each output has its own buffer, i.e. the three output sockets are not simply connected to each other. The lower output of the upper unit is normalled in the factory to the input of the lower unit. That way the module works as a single 1-in-6 buffered multiple provided that no signal is applied to the input of the lower unit. But it's also possible to pick-up the bus CV and normalize the input socket of the lower unit to the bus CV.

Application: copying/buffering of CV, gate and audio signals.
Read more
 1 in stock $47.30
Click for better price!
or call +44 20 7424 1960
quote 751720
Cat: 751765 Rel: 23 Oct 19
 
Gate/trigger combiner - 4HP
Notes: Module A-186-1 is a very simple, passive unit that combines up to 7 gate, trigger or analog signals by or-wiring.

Function:

- If all seven inputs are low or open the output is low
- If one or more of the seven inputs is "high" the output turns high

Applications:

- Combination ("or"-wiring) of gate and/or trigger signals (e.g. from LFOs, sequencers, keyboards, Midi-to-CV interfaces, ribbon controller, theremin, trigger delays or any other source of gate/trigger signals
- Maximum extractor for analog voltages: at the output the maximum voltage (minus ~ 0.7V because of the diodes) appears, similar function as the maximum output of the A-172 Maximum/Minimum Selector module, e.g. for simple waveshaping
- Simple half-wave rectifier
Read more
 1 in stock $45.16
Click for better price!
or call +44 20 7424 1960
quote 751765
Cat: 751728 Rel: 23 Oct 19
 
Dual passive attenuator - 4HP
Notes: Module A-183-1 is a simple passive dual attenuator. Passive means, that each unit is made of two sockets and a 50k linear potentiometer only. There are no active parts like amplifiers or buffers and no power supply is required.

This is how the A-183-1 works: At the output socket appears the attenuated input signal, i.e. zero level at the fully CCW position and max. level and the fully CW position.

Applications:

Adjustable level of CV or audio signals to control other modules that do not have attenuators (e.g. Dual VCA A-132-1, Quantizer A-156, CV-to-Midi interface A-192 and modules of other manufacturers).
Read more
 1 in stock $40.85
Click for better price!
or call +44 20 7424 1960
quote 751728
Cat: 751717 Rel: 23 Oct 19
 
Passive multi-port distributor - 2HP
Notes: 2HP narrow version of the A-180 multiples module. It is a passive signal splitter suitable for audio or CVs. Two sets of four jacks are interconnected, by placing a solder bridge you can connect all eight jacks.
Read more
 1 in stock $37.62
Cat: 752443 Rel: 25 Oct 19
 
32HP metal enclosure for Eurorack modules - Beta version
Notes: Limited Beta version of the popular Pod32. These are new, fully tested and functional units. The only difference between the Pod32 Beta and the regular Pod32 is that the Beta version has fewer holes to screw in modules. Most common Eurorack sizes will fit from 4HP to 32HP, but some odd sizes and combinations won't fit. Please refer to the product image, or visit the 4ms website for possible module combinations.

Pods are a perfect way to get started in Eurorack module, or add a couple more modules to your monster system!

Made from 100% anodized aluminium, Pods are light, tough and perfect for on-the-go set ups. Mix and match your Pods with desktop synths, effect pedals, drum machines or any musical gear for a flexible modular system. Need to add another module? Just add a Pod! Need to pack light for a live set? Just grab the Pods you need and go!
Read more
 3 in stock $26.07
Artículos del 1 al 38 de 38 en la página 1 de 1

Filter

Saved Searches
Save current search
Release Date
Featured
Close