Studio Equipment charts

Notes: Low-cost, portable, compact enclosure that turns Eurorack modules into table-top instruments.

The Pod32 is 32HP with 1.34" (34mm) of available module depth. The built-in power supply has two power connectors and can be daisy-chained to other Pods. More power connectors can be added with the Multi Power Cable accessory.

Pods require a power brick. If you already have a powered Pod and power brick (or a Row Power module) you can use a barrel cable to daisy-chain powered Pods.

The Pod32 includes ten (10) M3x8mm stainless steel screws and is compatible with M3 Knurlies.

Notes: This 30HP wide module features twelve fixed frequency, inductor based bandpass filters, set at half octave interval spacing and covering from 125 Hz through to 5.8kHz. It also features low pass and high pass shelf filters, again they are fixed frequency and both are active inductor based circuits. It has a vintage pedigree that harks back to the original and highly sought after 914 Fixed Filter bank from the 1960's Moog 900 series modular synthesiser system, however we have brought this design up to date and made it compact enough to fit into skiff friendly Eurorack cases by using gyrator based active inductors, and have added some other very useful features too - the bands are split alternatively to left and right channels, each having their own individual output, and there is also an inbuilt Voltage Controlled cross-fader that allows panning between the left and right banks, with a mix of all bands available in the central position.

In addition, we have a second cross fader that can mix between the dry incoming signal, or an external signal fed into input 2, and this is cross-faded against the wet MIX Output - this allows Voltage Controlled crossfading from wet to dry signals, or between wet and external signals - and the level of each can be adjusted using the Input 1 and Input 2 level controls.

A further addition is the feedback control, this is similar in design to the resonance control on a regular VCF, but because of the multiple fixed filters topology it is rather different in operation - it would normally be added in small amounts to thicken up the sound, however we have allowed the feedback to traverse to quite extreme settings for howling feedback and even soft clipped self-oscillation, especially for the noise merchants out there...

Using L/C inductor topology bandpass circuits rather than the usual Sallen Key R/C active bandpass filters does give a slightly different sound and this is part of the magic of the original 914 filterbank, as the LC based circuit exhibits less phase shift against frequency that the more common Sallen Key R/C based bandpass filters that are used in many Modular synths.

Many people often wrongly assume that a fixed filter bank is exactly the same as a graphic equaliser - however this is certainly not the case, if all of the controls of a graphic EQ are set to centre then a flat frequency response is expected and the output will sound very similar, or identical to the input - this does not happen with a fixed filter bank, the frequency response rises and falls as it passes between each stage (but to a lesser extent than if the filters are all set to maximum output), so it acts as a soft slope comb filter, and the resulting output sounds very different from the input signal. Also, with all of the individual filters turned to zero there will be no output at all.

Notes: The original MiniMod Glide +Noise module was based exactly on the original Minimoog Model D circuitry, which was designed to be used with the built in Model D keyboard, and because of its vintage design its range was severely limited to 5 or 6 octaves, and it also responded to positive voltages only. Another limitation was that it would not return fully to zero when selecting long glide times, which restricted the range even more.

So we made the decision to re-design the MiniMod Glide + Noise using modern precision parts, and we have come up with an all new circuit which has exactly the same function, but with a hugely extended range. It has the same Glide slope characteristic (a slightly curved Linear Glide) as the Model D on which the MiniMod is based, however in response to many requests from customers we have adjusted the glide up and down speeds so that they are now very similar , which is much more useful in real world applications that the earlier MK1 version which (like the Model D) would glide up considerably faster than it would glide down.

The new Mk2 MiniMod Glide Noise module now has an impressive 14 octave range, and can respond to negative voltages down to -5V. This is a very useful feature, as our MiniMod VCO's will respond to negative control voltages and produce correspondingly low frequencies; so it is now possible to glide down quickly or slowly to crazy sub bass levels! The hold feature has been improved too, it covers the full audio range as well as DC control voltages, and works as a track and hold module with Eurorack signal levels.

A further enhancement is that the Mk2 module can now (using selectable jumpers) transmit or receive pitch CV to the Eurorack power bus; for example, the Glide CV Output can now be directed to the Bus in order to send CV's to (for example) three VCO's via the bus without the need for a passive multi and four patch cords!

The Noise section of the module is unchanged, except that we have slightly boosted the level of the Red Noise output to bring it more in line with Eurorack control voltage levels.

Lastly, it is much shallower - Mk1 Glide Noise had a depth of 54mm, and it was the only MiniMod module that was too deep to fit a skiff style case - and this prevented a full MiniMod system being installed into a shallow Eurorack case. The new MK2 version is only 28mm deep, so this allows both it and a full MiniMod system to be mounted into shallow skiff style Eurorack cases.

Dimensions: 6HP wide, 26mm Deep
Current draw: 36mA Positive, 38mA Negative

Notes: Engineered in the UK specifically for the Native Instruments Maschine Mikro MK3 Controller, a tough but lightweight polycarbonate shell protects from dust, liquid and accidental impact. Precision moulded for an exact fit whilst accommodating cables, your Native Instruments Maschine Mikro can sit ready for operation. Slides straight into a flight case or bag ready for transportation. Shields delicate controls and internal components from damage at home, on the road and on stage.

Notes: Decksaver LE (Light Edition): Still made from super durable polycarbonate, but reaching you at a more affordable price.

Engineered in the UK specifically for the Teenage Engineering OP-Z synthesizer.

Custom moulded to fit the contours of the unit whilst leaving USB connections in place, the OP-Z can sit ready for operation.

Super durable polycarbonate shell protects delicate keys during transportation and slides straight into a flight case or bag for maximum protection.

Dimensions

Weight 0.12 kg
Length 22.6 cm
Width 6.4 cm
Height 3 cm

Notes: The tools we use to compose and produce music are dear to our hearts. Dust, liquid and accidental impact have taken many a good synth down over the years - this is where Decksaver steps in. Precision trimmed for perfect fit whilst accommodating cables, the TipTop Audio Mantis Case can sit ready for operation. This cover is designed with 55mm clearance for patch cables, meaning you can leave your cables in place when travelling or protecting your modular setup in the studio. Shields delicate controls and internal components from damage at home, on the road and on stage.

Notes: This snake is designed connect gear with unbalanced phone jacks to gear with phono jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed connect gear with unbalanced phone jacks to gear with phono jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed to interconnect pro audio gear with unbalanced phone jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: This snake is designed to interconnect pro audio gear with balanced phone jacks. It is ideal for use with mixing consoles and patch bays. Features include:

- Nickel-plated plugs for rugged durability and efficient signal transfer
- Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
- OFC spiral shields for effective EMI and RFI rejection and flexibility

Notes: 1/4 in TRS to Dual 1/4 in TS

This snake is designed to connect channel inserts on a mixing console to effects processors with unbalanced phone jacks. It is ideal for use in touring and other live-sound applications.

Features include:
Serviceable, all-metal plugs for rugged durability and ease of repair
Oxygen-Free Copper (OFC) conductors for enhanced signal clarity
OFC spiral shields for effective EMI and RFI rejection and flexibility

Connectors: Serviceable 1/4 in TRS to Dual 1/4 in TS
Conductors: 24 AWG x 2 OFC

Notes: Module A-140-2 contains two ADSR type envelope generators behind a front panel with 8 HP only.

Each ADSR provides these controls and in/outputs:

- LED (displays the envelope output)
- A: manual Attack control
- D: manual Decay control
- S: manual Sustain control
- R: manual Release control
- Gate Input
- Retrigger Input
- CVT Input with attenuator (CVT = CV Time)
- Envelope Output 1
- Envelope Output 2

The output voltage range for each envelope is 0 - 10V. The time range of Attack/Decay/Release is about 1ms to 30s.

By means of internal jumpers one can select which time parameters are controlled by the CVT input (e.g. D only or D+R or A+D+R) and in which direction (i.e. if an increasing CVT shortens or stretches the time parameter in question).

Socket CVT can be normalled to an internal fixed voltage (i.e. the switching contact is connected to an internal fixed voltage). That way it's possible to change all time parameters simultaneously by means of the CVT control.

Another jumper is used to set output 2 to normal or inverted envelope.

And another jumper is used for the normalling of Gate 2 to Gate 1 (i.e. ADSR#2 is also triggered by Gate 1).

Two more jumpers are used for the optional bus access to the gate signal of the bus for each ADSR. Changing the positions of the mentioned jumpers allows to modify the factory settings.

Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in/outputs, and a common out/input. Each time a pulse is received at the trigger input socket, the common out/input is connected to the next in/output. After the fourth in/output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out/input immediately back to the first in/output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LED's indicate the active in/output (ie. the one that is connected to the out/input at any particular time).

Notes: When you need to do serious work without bothering anyone in your living space and without being distracted by outside sound, choose PreSonus HD9 headphones. They're clean-sounding, extra-comfortable, and offer a broad, transparent frequency response that ensures accurate mixing.

The HD9's closed-back acoustic design provides superior listening isolation and reduces headphone bleed, so you hear nothing but music - and your housemates hear nothing at all.

The HD9's 45 mm dynamic, neodymium drivers and high-power handling (900 mW per channel into 40 ohms) deliver loud, clear, clean audio, minimizing listening fatigue. Best of all, its tailored frequency response extends all the way from 10 Hz to 26 kHz, with accurate bass response, enabling precise mixes.

The lightweight HD9 features an adjustable headband, cups that rotate 180 degrees on two axes, and comfortable, durable ear pads. The straight, ten-foot cable drops down one side so it doesn't get in your way. The result is a comfortable listening experience that you'll continue to enjoy during long sessions. And the HD9 is built tough so you can rely on it wherever your travels take you.

The PreSonus HD9's are an invaluable addition to your sonic toolbox. While there will always be a place in the studio for powerful and articulate studio monitors, fact is that more people are choosing portable, personal listening solutions nowadays. As trends in listening shift, it's wise for you to check your mixes on high-quality headphones as well as on your finely calibrated studio monitors. With the HD9's, you can rest assured that your mixes are translating well across myriad listening environments.

And with the HD9's combination of comfort, adjustability, sturdy construction, and acoustic isolation, you can mix better for longer.

Notes: If you need the production power of FL Studio, but don't need to deal with audio recording or audio clips, then FL Studio Fruity Edition 20 will fit the bill. FL Studio Fruity Edition 20 gives you full access to a powerful piano roll editor, which lets you sequence and arrange your virtual instruments to your heart's desire. It also gives you access to FL Studio's powerful step sequencer, 18+ virtual instruments, and over a dozen built-in effects and processors. Add to that unlimited tracks, VST and DXi instrument support, and full automation capabilities, and you'll be hard pressed to find another electronic music production system that offers as much value as Image Line's FL Studio Fruity Edition.

What you can do with FL Studio Fruity Edition 20:

- Automate most interface and all plugin parameters by recording, drawing, spline-based automation curves, automation generators with formula-based control of links.

- Record & play MIDI input recording from keyboards, drum pads and controllers.

- Sequencing and arranging with pattern and linear workflow possible.

- Synthesizer & effect plugin hosting VST 32 & 64 bit, DX and FL Native formats.

- Open plugin standards - FL Studio supports all PC industry plugin instrument standards including VST, DX, Buzz and Rewire. This means you can sequence with your favourite plugins and applications.

- Pattern or track sequencing - You choose, record your musical performances and ideas in the most logical way. FL Studio 20 can simultaneously function as a pattern and track based sequencer. Reuse patterns as Pattern Clips in the Playlist or record song-length sequences, as desired.

- Step sequencer or Piano roll - Scoring tools include FL Studio's legendary Step-sequencer, one of the most advanced Piano rolls in any software studio, event and multipoint automation envelopes. FL Studio supports MIDI input, standard controller compatibility, and the ability to simultaneously control multiple instrument channels from separate controllers.

- Determine your own project design - In FL Studio 20, you decide how your project will be laid out, including multiple 'Arrangements'. Unlike the competition, FL Studio 20's Playlist is a totally flexible and virtually unbounded workspace where - Note Pattern, Audio and Automation data can be arranged and edited to suit your creative ideas and preferred workflow.

- The mixer - is about precision, control and flexibility. The mixer's tracks each hold up to 10 effects (VST or FL's proprietary format). To create sub-mixes or mixing chains of almost unlimited complexity, each mixer track can be routed to any other mixer track or the Master track. Sends provide the ability to sidechain inputs to multi-input effects plugins. Finally, each of the mixer tracks can be routed to any output on your audio interface, now that's flexibility.

- Effects - What about effects? FL Studio 20 includes more than 40 effects spanning maximization, limiting, compression, delay, distortion, equalization (graphic & parametric), filtering, phasing, flanging, chorus, vocoding and reverb. These have you covered for the creative broad-brush effects, through to the minutia of the mastering process.

Notes: ADSR is a four stage linear envelope with two expressive ranges. Each stage can be modified independently allowing for the creation of complex, multi-segment envelopes. Great for modulating filters, VCAs, and oscillators.

Notes: Arp is a gate-driven arpeggiator with a multitude of chord types and playback modes. Voltage control over both root note and chord type allow for sequencing any combination of chords in any key imaginable.

With the rate of the arpeggio and reset capability in your own hands, you're free to create dynamic rhythmic melodies from your favourite chords. Take your tonality for a ride with Arp.

Notes: Clk is a voltage controlled clock generator with all the features a master clock needs. It has an extremely wide range from ten seconds between pulses well into audio rate. In addition, the pause button and CV input provide an expressive feature that is all too often missing in a modular setup. Stop using LFOs or other modulation sources for your master clock, and let Clk do what it's best at.

Notes: Mix is a 4 channel mixer that is great for audio or control voltage signals. Up to four inputs can be combined to a single output each with its own level control.

Notes: Mult is a 2 input, 6 output signal splitter. Channel 1 is normalled to channel 2 when no cable is present, allowing the user to split an input signal six ways, or two input signals with three outputs each.

Notes: The 2hp VCA is a dual, linear VCA. It uses the renowned 2164 SSM architecture, giving it extremely low distortion and high quality audio outputs. With a CV input attenuator, and DC-coupled inputs this is your new go-to module for voltage controlled amplification of audio or CV.

Notes: Verb is a lush stereo reverb with a full feature set and superior audio quality. A wide range of reverb times take your sound from small room to never-ending concert hall.

CV over mix allows dynamic movement between the dry and reverberated sound, and the dampening control lets you dial in the perfect timbre for the wet signal. Whether you need a traditional reverb for an FX send or an esoteric sound design tool, Verb can take you there. Get lost in space with Verb.

Notes: Erica Pico INPUT module is just what you need to interface your modular system with external synths or even your mp3 player or mobile phone.

It boosts external signal to modular synth signal level.

With the Pico Input, line signals from, for example, a synthesizer, drum-computer, audio interface or smartphone can be raised to modular level. The module delivers up to 40 dB of gain. Thanks to its two channels, users can comfortably process mono as well as stereo material.

The Pico Input comes equipped with two signal paths. Each signal path features an audio input, a volume potentiometer and an output. Up to 40 dB of amplification are available. Using jumpers on the circuit board, it is possible to dampen the maximum gain to 20 dB. The module's first input is a stereo jack, meaning the user can connect a smartphone or tablet without any adapter cables. In this case, incoming signals are distributed internally to both channels.

Notes: Erica Pico Quant is advanced CV quantizer with some unique features - quarter tone accuracy and the web-based interface for creating user generated scales.

- 8 preset scales
- Web based interface for user generated and extra preset scales
- Microtonal quarter tone scales
- Adjustable tolerance
- Adjustable CV glide between notes
- Clocked and independent quantization

Dimensions
3 HP
35 mm deep

Current Draw
25 mA +12V
6 mA -12V

Notes: Erica Synths Pico VCO is a great, deep sounding VCO with 32 selected waves: classical, fattened with sub-oscillator, FM synth and others.

Features
2 banks, 16 waves each
VCO/LFO mode
Voltage controlled wavesurfing
Wave morphing in LFO setting
Typically you would need several rather expensive modules to generate similar sounds, besides there's an extra feature: flip a switch, and you have a versatile LFO.

With Pico Series we challenged ourselves - can we make ANY superior functionality synth module 3HP wide and affordable? Yes, we can.


Technical specification:

VCO frequency range: 30Hz - 5kHz
LFO frequency range: 0,1Hz - 20Hz
1V/Oct input signal amplitude: 0V - +10V;
Output amplitude: 10V ptp
Power consumption: +26 mA, -4 mA
Module width: 3HP
Module depth: 35 mm

Notes: Erica Pico VCF1, is a younger brother of Erica Black Polivoks VCF, designed on the similar topology using rare Russian op amps. As result you get a filter great for acid bass lines, screaming resonance sweeps and deep wobbles.

Features:
- Lowpass and bandpass modes
- Self oscillation
- Rare russian opamps used
- Input protection against overvoltage

Dimensions
3 HP
35 mm deep

Current Draw
12 mA +12V
11 mA -12V

Notes: Erica Pico RND is combined LFO/random source module.

It generates sine LFO waves, white noise, S&H CV and some interesting stuff - random triggers and pulse wave with random duty circle; basically, everything, you need, to bring some uncertainty in your modular setup.

The Pico RND comes equipped with five outputs, they emit the following signals:

- Sine waves
- Pulse waves with varying width
- Random triggers
- Sample and hold material
- White noise

The speed of LFO and S&H circuit can be edited using the module's potentiometer (Range: 0.1 Hz to 20 Hz). For synchronizing the Pico RND with other gear, a clock input was implemented.

Notes: Pico DSP is a small brother of the popular stereo effects processor Black Hole DSP. It contains eight algorithms, in detail four delays, two types of reverb, Leslie speaker emulation and an Overdrive/Bitcrusher. Each effect is editable in two parameters. One of them can be modulated using the CV input. Pico DSP features clear, high-resolution sound. Alongside the established standards, it is also possible to generate lots of freaky special effects.

Notes: Erica Synths Pico OUTPUT module is just what you need to monitor your music on headphones and have standardized connection to mixing desks.

Features

Stereo input
High quality headphones amplifier
3,5mm headphones output jack
Headphones volume control
3,5mm stereo line output jack
The 3,5mm stereo output jack in this module allows you to connect the Pico System directly to virtually any speaker system or line input. Even in your car!

With Pico Series we challenged ourselves - can we make ANY superior functionality synth module 3HP wide and affordable? Yes, we can.

Technical specification:

Input level: 10Vptp
Power consumption: +20mA, -7mA
Module width: 3HP
Module depth: 35mm

Notes: Erica Pico Voice is amazingly versatile sound source in just 3HP. It features 8 sound generation algorithms: Karplus Strong, Chords, Wavetable, TB303 bassline emulation, PWM, Supersaw, Wavefold and Harmonic saturation, with three adjustable parameters per algorithm and CV control over one user defined parameter. Despite the small size, Pico Voice sounds bigger than it is!

Dimensions
3 HP
35 mm deep

Current Draw
30 mA +12V
20 mA -12V

Notes: Small desktop enclosure for Eurorack modules with 42 HP space and a maximum depth of 32mm. A relatively strong power solution with an external power supply and an on/off switch located at the case is included.

The power supply provides:

- 850 mA at +12V
- 850mA at -12V
- 500mA at +5V

The power distribution has 14 connectors and the case can house exactly fourteen modules from Erica's Pico Series.

Notes: Erica Synths MIDI thru box is professional quality, no latency, one MIDI In to 8 MIDI Through splitter in rigid aluminium case. It allows to connect up to 8 instruments to your sequencer or master keyboard and control them simultaneously without undesired delays and interference.

Notes: Two steel monitor stands, extendible from 75-130 cm. Max. load each: 30 kg.

- Adjustable monitor stands with cotter lock
- Particularly suited for 5.1 systems or close-range monitors
- Sturdy cast iron foot
- Comes as a pair
- Powder-coated steel version
- Colour: Black

Notes: Standard USB 2.0 type A plug to type A plug lead, suitable for connection of printer, hub, audio devices etc, to PC.

Notes: The 'Quaid Megaslope' is a five stage function generator or modulator which operates in one of 3 modes; a multistage 'CZ' or 'Juno' style complex envelope, a super flexible LFO and a step sequencer with per step programmable slew or slides.

Each mode produces a varying output voltage moving from point to point across a set number of chained together stages. Each stage features a destination level, an overall rate or time to reach its destination level and a variable slope for the output path to take. As well as direct control, every stage feature voltage control of both level and rate. There are both unipolar and bipolar voltage outputs together with triggers emitted for the end of each stage and the end of a full cycle.

The Quaid Megaslope is designed to be fun, flexible and intuitive to use.

Notes: The 'HPO' is an affordable super slim and skiff friendly no frills stereo headphone driver output for your modular synthesiser. Includes a volume control and ability to double up a mono signal into stereo. A great use for that left over 2hp in a skiff or larger system.

Give loved ones, friends and acquaintances a break from your musical 'genius', the HPO offers a solitary cell for focused creativity impregnable from undeserving non-believers.

Notes: The WaveSwarm is a waveform animator and all analogue dual channel device.

Each channel simulates up to six VCO's beating in unison with a different beat frequency between each animation. The fixed beat frequencies are generated by twelve onboard LFO's, and the front panel pots control the level of each of the six animators, along with the level of the dry signal to the final mix. In addition to independent channel inputs and outputs it also has an A+B output, which sums the outputs of the two channels, creating an effect similar to twelve VCO's in unison! This is possible because channel B uses slightly different beat frequencies to channel A, they are not identical.

The input waveform can be saw, triangle, sine or wavetable/complex waveforms, in fact most waveforms with the exception of square or PWM waves will give some form of animation.

A soft clip circuit is built in so that at higher signal levels the signal magnitude is limited by rounding the top and bottom of the waveforms, thus slightly softening the sound. There are soft clip LED indicators for both channels.

It can produce huge, fat drones or supersaw type waveforms from a single sawtooth or triangle wave input.

Notes: This new device is a powerful new CV controlled effects unit for your electronic music setup and pairs extremely well with the KOMA Field Kit.

- Looper
- Frequency Shifter
- Sample Rate Reducer/Bitcrusher
- Digital Delay
- Analogue Spring Reverb
- 4 Channel VCA Mixer
- 4 Step Mini Sequencer
- Envelope Generator

All of this, combined with the new 4 Channel CV Interface which allows you to route four CV signals throughout the device, means an incredible control over sound and timbre and a great addition to your mobile performance rig.

The Field Kit FX is built up from 7 separate functional blocks all focused on mangling and changing incoming audio and CV signals. They are designed to operate together as a coherent addition to our Field Kit Electroacoustic Workstation or alternatively together with other pieces of music electronics with the ability to use control voltage signals.

Notes: Additive synthesis oscillator based on the concept of building up harmonics from sine waves. A complex idea nicely executed for ease of use.

Suppliers notes:
Odessa implements the principle of additive synthesis controlled by a set of carefully tailored macro parameters to harness thousands of sinusoidal partials that altogether form the resulting sound.

The interface is kept simple and accessible, so you can easily build rich and full, great sounding timbres of very complex spectra, that can be either harmonic or inharmonic. Even though inharmonic spectra yield non-periodic waveforms, all partials are frequency related to the common fundamental controlled by a V/oct input. The series of harmonics can be squeezed or spread apart, tilt, and pruned by a comb-like frequency response, resulting in a variety of unearthy sounds. Animating the comb response yields radical effects similar to flanging and phasing. Additional, often sought after features are implemented: through-zero linear frequency modulation, and unison detune: up to 5 copies of the sound can be spread apart for a fat and dense cluster of voices.

There are nine parameters, each controlled by a dedicated knob, so the workflow is as smooth and immediate as possible. Furthermore, every parameter has a dedicated CV input, allowing live animation for organic audio effects. Odessa sports two main outputs for banks of harmonic partials that can be further scaled in frequency, as well as an additional output that can either spit out a square wave or a single sinusoid of the fundamental frequency. Interesting spatial effects, crazy modulation feedbacks as well as synchronisation is possible that way.

The hardware is based on a powerful FPGA chip offering massive parallel computing. The synthesized signal is devoid of aliasing through the entire audio range thanks to intrinsically bandlimited algorithm. A simplified spectral analyser helps you to keep a visual track of what is actually happening to the harmonics.

For even more control over Odessa, you can use the Leibniz subsystem (or just the Lipsk) that can be connected to a header at the back of the module.

Notes: IsoAcoustics introduce the next evolution of their specialized line of speaker stands for the audio professional, music hobbyist, audiophile, and music lover. The new ISO Series of speaker stands provide superior acoustic isolation and enhance the sound clarity of any speakers including studio monitors, home theatre systems and sound reinforcement.

With a lower profile and new contemporary design, the ISO Series of stands positions your studio closer to the supporting surface or meter bridge, and the new redesigned isolators moves the acoustic performance another step forward.

IsoAcoustics ISO Series speaker stands are built with a unique, patented isolation technology that provides a high degree of isolations and manages the speaker's energy to deliver authentic, uncoloured sound. This next generation of speaker stands effectively eliminates energy transfer into the supporting surfaces. Bass becomes tighter, overall imaging is enhanced and your speakers are enabled to perform to their full potential. Following the same design philosophy as the ISO-L8R Series, these isolation stands provide 14 variations of height and tilt adjustment to optimize the placement and performance of studio monitors by getting the tweeters in the correct alignment with the listening position.

Whether you're a pro mixing in the studio - a musician creating in a home project environment - or an audiophile who appreciates every nuance of music and sound - you'll hear and appreciate the difference with the ISO Series speaker stands. It's simply the best investment you can make for superior audio.

ISO-130:

Designed for smaller speakers and studio monitors. These stands provide 14 variations of height and tilt to optimize speaker placement and performance. Isolate your studio monitors from the supporting surface and allow them to breathe so they can deliver the clearest and most accurate sound possible.

5.1"x6"/13x15cm Short: 2.7"/8cm Tall: 8"/20.3cm 20 lbs/9kg

Notes: The Multi-Delay Processor is a creatively usable echo effect with eight taps. The module's sound may remind you of classic bucket-brigade devices. - It even generates distinctive pitch effects when altering the delay time. An input mixer gives audio material a crisp, analogue character. Thanks to feedback channels with pitch shifter and reverb processor, shimmering echoes and other atmospheric effects can be achieved. A total of nine envelope followers and 14 audio outputs invite you to do extensive feedback patches and other edgy experiments.

The Multi-Delay Processor isn't just a high-quality echo effect but was designed to be a fundamental ingredient of patches. Its core is a bank of eight digital delays, which are wired in series. Together, the circuits form a multi-tap echo. The volume of each signal repetition as well as the raw material can be adjusted via faders. Furthermore, there are individual audio and envelope follower CV outputs for the dry signal and all taps. An analogue clock is used to control the echo circuits. The delay time can be set manually via a potentiometer plus there are two CV inputs with bipolar attenuators. Altering the delay time parameter during operation leads to pitch effects. At this point at latest, you'll realize the superiority of the serial memory design used by Mark Verbos over average effect chips. Despite its digital core, the Multi-Delay Processor offers charming sound reminiscent of a classic bucket-brigade device. - Only cleaner and more transparent.

A three-channel mixer with dedicated level potentiometers adds analogue character to signals before they are fed to the delay circuits. Without patch cables plucked into the second and / or third input, you can use these channels as feedback paths with additional effects. In detail, a pitch shifter calibrated to +1 octave (channel 2) and a reverb (channel 3) are available. - A perfect setup for creating shimmering echoes and other atmospheric effects. High feedback values make the module self-oscillate. In contrast to the multi-tap delay, which consists of individual components, an FV-1 chip is used for pitch shifting and reverberation. This processor is well-known, as it is the main component of multi-effects modules like the Erica Black Hole DSP and numerous guitar pedals. Here, the FV-1 is "just" a creative addition to the main effect.

In addition to the manual mix output, which emits the mixture of raw and effect material dialled in via the faders, there are four other audio outs. Two of these connectors provide signals derived from summing up all even respectively odd taps. The other sockets emit preset mixes with increasing or decreasing level. - Very cool for quickly creating special effects.

Notes: Erica Synths Clap is developed together with French company e-licktronic and it's our take on analogue clap circuits adapted for modular systems. Sharp, punchy sound, Accent & CV control over Tone make it distinctively expressive in studio and live performances.

Features
Tone and Decay controls
CV control with an attenuator over Tone
Manual trigger
Accent for Better expression

Decay range: 120ms - 1100ms
Audio output level: -5...+5V
CV level (full span): -5 - +5V
Trigger level: 5V
Trigger time: 1ms
Accent CV level: 10V
Power consumption: 24mA@+12V, 20mA@-12V
Module width: 6HP
Module depth: 35mm

On this run of modules the Pitch & Decay CV inputs are inverted: rising CV will decrease pitch, falling - increase.

Notes: Erica Synths Drum Mixer Lite is compact version of Drum Mixer. It features extended headroom and a dedicated drum compressor of unique design keeps each drum sound clearly distinguishable and add power to the final mix. Bonus feature - effects send output allows to apply external effects to the signals on the first three inputs. LEDs next to each input give visual feedback on the signal level.

Features:
6 inputs
Built in vactrol based drum compressor with Amount and Decay control
Three inputs assignable to main or aux send outputs
Main and Aux Send outputs
Signal level indicator LEDs

Mixer gain: -+6dB
Power consumption: 59mA@+12V, 36mA@-12V
Module width: 10HP
Module depth: 35 mm

Notes: To add some space to your compositions and nuances in sound design Erica Synths Dual FX module brings you two identical sections of 8 custom effects with two adjustable and CV controllable parameters.
Dual FX combines two Spin FV-1 chips in one module, each filled with eight custom effect programs with two adjustable and CV controlled parameters per effect and analogue dry/wet circuit. All parameter settings can be saved with the effect and recalled instantly during the performance. Also the output of the first FX section is normalised to the second input so creating huge layers of effects is easy.

FX:

Mono delay
Stereo delay
Hi-pass delay
Big reverb
Saturated reverb
Stalker reverb
Ripper
Dual pitch shifter

Technical specs:

Audio output level: -5...+5V
CV level (full span): -5...+5V
Power consumption: 118mA@+12V, 61mA@-12V
Module width: 10HP
Module depth: 45mm

Notes: With 11 reverb types and a ton of "hidden" functionality, the Electro-Harmonix Oceans 11 reverb pedal could be your new go-to reverb pedal. You can tap into classic tones like hall, plate, and spring reverbs, including a brand-new spring reverb algorithm that sounds gloriously complex and rich - you can even double-tap the footswitch to "crash" the spring reverb. And you'll be able to cover a huge range of modern tones with a variety of modulated reverbs, shimmer reverb, reverse reverb, and more. A mode switch offers access to variations on many of the 11 reverb types. Complete with an infinite reverb mode for freeze-style effects, there is vast creative potential in the Electro-Harmonix Oceans 11 reverb pedal.

Reverb types:

Hall - rich and full sound of a grand concert hall
Spring - brand-new tube spring reverb emulation
Plate - lush and warm plate reverb
Reverse - each note fades in backwards
Echo - recirculates echoes through the plate reverb algorithm
Trem - hall reverb plus tremolo
Mod - modulated reverb
Dyna - swells, gates, and ducks in response to your playing dynamics
Auto-Inf - auto-infinite reverb, triggers a wash of reverb with each new note or strum
Shim - shimmer reverb with an octave-shifted wash that blooms behind your core tone
Poly - polyphonic reverb with two pitch shifts operating on your pre-reverb guitar tone

Notes: *** NO POWER SUPPLY INCLUDED - USES GENERIC 12VAC ADAPTER ***

Basically, the Ekdahl Moisturizer is a spring reverb where the springs are exposed so they can be played/hit/fiddled with. As well as being capable of creating sound in itself, you can of course also play sound through the springs like a regular spring reverb - this makes for happy-fun-time finger-modulation of the reverb on whatever audio that's going through it. On top of this there's an analog multimode filter that can be used to attenuate or exaggerate certain frequencies in the sound, this is real handy while playing the springs as you can - for instance - cut all the highs and just make thunderous doomy sounds or do the opposite; cut all the lows and make that ear piercing high frequency special love. Also, it incorporates an LFO that's internally routable to the filter and that also has some external routing-stuff. The Ekdahl Moisturizer has tons of CV / Expression pedal options on the back for even more hillarious moments. The Moisturizer is a mono unit.

The Moisturizer was developed with the help of Jason Willett (Half Japanese, Leperchaun Catering), Martin Schmidt (Matmos, Instant Coffee), Joshua Atkins (Polygons, Major Powers), mom & dad and many more.

The Ekdahl Moisturizer contains exactly:
Preamp (up to 10 times gain)
Reverb
Reverb / Preamp wet/dry crossfader (Knob & CV/EP controllable)
State variable filter with
Lowpass/Bandpass/Highpass seamless crossover (Knob, CV/EP & LFO controllable)
Cutoff (Knob, CV/EP & LFO controllable)
Resonance (WITHOUT resonance limiter)
LFO with
Speed control (Knob & CV/EP controllable)
Square / Triangle crossover
External output with output amplitude knob
Filter / No filter wet/dry crossfader (Knob & CV/EP controllable)

The preamp section is designed for a max of 10 times gain, this to accomodate for low level output instruments such as guitars etc. The reverb tank has normal reverb signal gain on it, meaning that if you hit the springs hard they'll distort like crap which is real nice, if you hit them softly the sound won't be distorted.

The filter in the Ekdahl Moisturizer is abrasive, the fact that it doesn't have any resonance limiting makes it possible to get the filter to sound *really* bubbly & metallic (way more then any filter i've ever heard), but it's also of course capable of sounding completely "normal" - it all depends on the amount of resonance and/or gain. The fact that you can seamlessly fade inbetween lowpass, bandpass or highpass filter (or lowpass+bandpass and highpass+bandpass) makes the unit pretty damn versatile and by using the wet/dry filter/no filter crossfader there's some neat shit that can be done too. Now it should be said that due to the fact that there's no resonance limiter, if using very high gain, with high resonance and turning the cutoff frequency very high the filter might cut out - not to worry, just turn the cutoff back a bit and the filter pops in again. This happens because the filter gets overloaded and can be avoided with a resonance limiter, however if i had one of those all the super-awesome bounce would be gone and it'd sound like all the other filter out there.

The Ekdahl moisturizer has six CV/Expression pedal related jacks on the back, one of them is a LFO output so you can control other shit with The Moisturizer's LFO. All the other jacks are inputs and takes either CV or Expression pedal, they are: Reverb Mixture, VCF Cutoff, VCF Filter Mode (LP/BP/HP), Filter Mixture and LFO Speed.

Notes: Mariana Trench is an FDN card for the Z-DSP. Feedback Delay Networks (FDNs) are built around multiple delays which are connected to their inputs thanks to a feedback matrix designed for its stability and lossless properties. FDN can mimic the recursive process of sound waves bouncing back and forth in an acoustic space. They were first suggested for artificial reverberation by Michael Gerzon (1971) and later John Stautner and Miller Puckette (1982) introduced four-channel FDN reverberator with general stability conditions.

FDN can also be used as a special case of digital waveguides, they can be tuned, or also used as complex delays. The Mariana Trench Z-DSP cartridge is designed to explore these more unusual sides of the FDN algorithms. Mariana Trench Z-DSP cartridge is designed by Christophe Duquesne Anckorage - Haken Audio developement team - La Voix du Luthier.

Notes: The MOOER GROOVE LOOP brings together both the MICRO LOOPER and MICRO DRUMMER into one micro pedal, for the ultimate in a portable jamming companion. Both elements can be used independently from one and other or simultaneously.

When used simultaneously the looper will be automatically synchronised to keep in time with the selected drum groove, and an intro click will be played when recording the first loop to ensure you're in time with the groove.

The tap tempo button makes adjusting the groove speed very easy and independent playback level controls for both the Drums and the Looper ensure GROOVE LOOP is a breeze to dial in and adjust on the fly.

Notes: Ten-channel version of one of the most cost-effective mixers on the market. Great sound, good EQ and handy built-in effects. Check out the 12-channel version if you prefer faders for level control.

Supplier's notes:
The Allen & Heath ZED-10FX mixer is an amazing little desk for small band mixing. It is ultra portable for carrying to the gig, and can be used for recording live or in the studio. It comes with configurable USB audio in/out making it easy to capture stereo recordings.

Guitars can be plugged in directly to the mixer using the specially designed high-impedance inputs, while the mixer has two stereo inputs for MP3/CD players or keyboards. Equipped with professional XLR stereo outputs and a flexible monitoring section with headphone and speaker feed outputs. We've added a set of fabulous effects to give shimmering reverbs and enhance your sound.

USB AUDIO FLEXIBILITY
Getting audio to and from a computer easily is now a common requirement for live sound and music production. The way this has been implemented on ZED is super-flexible and super-easy! No longer do you need to fiddle around the back of your PC to get to the soundcard inputs, only to find that the levels are all wrong and noisy. Just plug in a USB lead to your ZED, select the USB routing on the mixer and the device on your computer and that's it! CD quality audio to and from your PC or Mac. Switches and connection through jack socket terminals provide different send/return configurations:-

SEND OPTIONS:
1) Main Mix Left + Right (Post master Level)

2) Aux + FX bus (Aux is a pre-fade send, FX is a post-fade send)

3) Record Bus Left + Right (Separate stereo bus to Main Mix)

RETURN OPTIONS:
1) To Playback input (through jack socket break contacts)

2) To Stereo 2 channel (through jack socket break contacts)

ZED-10FX features a responsive 3-band, swept mid frequency EQ design which utilises MusiQ - with optimised slope (or Q factor) for equalising individual instruments.

ZED-10FX has an essential selection of 16 time-delay effects, designed for small groups who don't want to carry around an effects unit with their gear but who still want great quality FX at their gigs and on their recordings. Our DSP engineers worked hard, crafting and refining beautiful reverb algorithms to enhance every performance. These effects are available nowhere else at this price point - this quality and integration is only available from the ZED-FX. ZED effects are easily controlled using 3 buttons with 9 display LEDs. For example, the ideal delay time can be quickly tapped-in, or the perfect amount of reverb on the lead vocal can be dialled-in. There is one-stop navigation and editing - in fact, it's just as easy as using effects pedals. To alter effects parameters, the TAP button is held down and the up/down buttons pressed to adjust the specific parameter for that effect, for example, the decay length on PLATE, or the depth on CHORUS.

ZED-10FX's pre-amps are similar in design to our MixWizard range of mixers, but with a twist! Inputs 3 & 4 have a high impedance jack input capable of taking either a normal line level or a low level input from a guitar pickup. These newly designed inputs have been crafted with the aim of replicating the sound of a classic guitar or instrument tube pre-amp in a combo or head amp. An extremely high input impedance ensures loading on pick-ups is minimal and a Class A FET (field effect transistor) circuit powered from 48V is employed to give the valve-like gain stage. There is a gain "Boost" switch associated with the guitar inputs which boosts gain by 26dB to cater for instruments with very low level outputs and the overdrive characteristics of the guitar inputs are very similar to a valve (tube) circuit, being asymmetric and soft. All this makes for a wonderfully natural sound to be reproduced from the instrument, full of warmth and character.

The ZED-10FX is bundled with IK Multimedia's AmpliTube X-GEAR software, giving access to superbly modelled amps and effects.

Notes: The definitive MIDI controller keyboard, KeyLab MkII is a luxurious, expressive tool for your studio or live rig. Unsurpassed connectivity, effortless integration, customizable interface, and inspiring included software; there simply is no other MIDI controller quite like KeyLab MkII.

KeyLab MkII is an expressive, versatile, and superbly powerful next-generation USB MIDI controller keyboard. It features dynamic performance and studio controls, including a high quality 49-note keyboard with aftertouch, 16 RGB backlit pads, 9 faders, 9 rotary knobs, and dedicated DAW and transport controls. Its huge connectivity also includes CV/Gate outputs, so you can take command of outboard synth and Eurorack modules with ease. Factor in the amazing included software, and you've just found your ideal creative companion for the studio and stage.

Another level in terms of quality and luxury, KeyLab MkII is a treat for the fingertips and gives unprecedented levels of control over your music and software.

Both 49-key and 61-key versions of KeyLab MkII feature Arturia's Pro-Feel action, the same lusciously playable keybed as the MatrixBrute and MiniBrute 2. Sensitive enough to accurately capture the subtleties and nuances of delicate playing, while still being robust enough to feel the energy of high-impact playing.

Every version of KeyLab MkII also offers 16 RGB-backlit, multi-function performance pads which can be used in a huge variety of ways, whatever suits your performance style or studio needs best. Trigger custom chords, activate samples, quickly switch user maps, KeyLab MkII puts the "control" firmly back into "controller".

A gateway to software, KeyLab MkII features 9 rotary encoders, 9 faders, and a selection of fully assignable buttons to give you unfettered access to your virtual instruments, effects, and recording environment. Send and receive CV/gate data to bridge the gap between modular and MIDI, with a fully customizable setup.

To allow for maximum expression, and to put that unmistakable "human touch" into your music, KeyLab MkII features multiple expression pedal inputs, that can be assigned to whatever parameters you desire in your DAW or virtual instruments, and sports robust, luxurious machined metal pitch and mod wheels. Truly a live-performers dream!

Amazingly versatile, hugely expressive, and geared up to enhance your creativity and workflow wherever your music takes you.

Included is an impressive software bundle: Arturia's complete Piano V virtual piano instrument, Analog Lab 3, and Ableton Live Lite.