Tags: Clock modulator module

Notes: 'Pamela's PRO Workout' is a compact programmable clocked modulation source for your Eurorack modular system. It provides 8 highly editable outputs producing various control voltage signals correlated and synced to a BPM based master clock.

Each output can provide everything from simple clocked triggers, complex rhythmic waveforms, quantised melodic patterns to random chaos with direct and assignable CV control over numerous parameters. These features together with a quick and easy to use interface provide almost limitless synced modulation possibilities in a tiny space.

Building on the original 'Pamela's Workout' & 'Pamela's NEW Workout' the evolved 'PRO' Pam maintains the precursor's form factor and intuitive workflow but improves and adds many new features with upgraded hardware, more CV inputs, a new full colour hi res display and rewritten software adding many new enhancements like micro grid timings and cross output modulations.

Through optional expander modules more CV input and outputs can be added with support for external non euro equipment through Midi and Din Sync outputs. Please enjoy your next generation PRO workout!

Size: 8HP
Power: +12v 60ma / -12v 10ma
Depth: 32mm (approx with power header)
Outputs: 0-5v buffered low impedance. 12 bit res. 3.8khz max update freq.
Inputs: CV 0v-5v / Clock, Run - rising edge 700mV min.

Notes: Module A-160-2 is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses. The Clock input will take any digital signal from, eg. LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2 also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

These are the most important features of the module:

Three different sets of dividing factors, selected by a three-position switch at the front panel:
- Power of two: 2, 4, 8, 16, 32, 64, 128
- Prime numbers: 2, 3, 5, 7, 11, 13, 17
- Integer: 2, 3, 4, 5, 6, 7, 8

Two output modes, selected by a two-position switch at the front panel:
- Gate mode: outputs act like the outputs of typical binary dividers
- Trigger mode: in this mode the outputs are AND-wired with the clock signal (i.e. the clock pulsewidth affects the pulsewidth of the outputs)
- Clock edge type selected by a jumper on the pc board:
- Positive: the rising edge of the clock signal triggers the state change of the outputs
- Negative: the falling edge of the clock signal triggers the state change of the outputs

Reset behaviour by two jumpers on the pc board:
- Level triggered: the level at the Reset input triggers the Reset
- Edge triggered: the edge of the signal at the Reset input triggers the Reset
- Positive: a high level (> 2.5V) or the rising edge at the Reset input triggers the Reset
- Negative: a low level (< 1 V) or the falling edge at the Reset input triggers the Reset

Output polarity selected by a jumper on the pc board:
- Positive: non-inverted outputs
- Negative: all seven outputs are inverted

Width: 4HP / 20mm
Depth: 35mm (Measured from the rear side of the front panel)
Current: +12V: +50mA, -12V: -0mA

Notes: Immense power in this multi-featured sequencer from one of our favourite brands. Four channels of 64-step sequences with advanced options including probability, quantising and randomisation.

Supplier's Notes:
The Erica Synths Black Sequencer takes classical modular sequencing to the next level by adding tons of features required for contemporary modular synthesizers.

The Black Sequencer features 4 channels with CV, gate and modulation outputs, up to 64 step sequences that can be chained into songs, independent track time divisions, multiplications and lengths. It includes a built-in quantizer, LFOs, envelope generators, parameter randomization, a MIDI in/out and many other features essential for composing and performing electronic and experimental music. Even though it provides many programmable parameters per step, it's intuitive, easy and straightforward to use, and could well become a master controller for many modular setups.

Black Sequencer firmware 1.04 is now available!

It adds output quantiser which can quantise track outputs in real time or rewrite notes in the sequence. Update also adds new track and synced LFO time divisions.

Technical specifications:

Power consumption: +145mA, -25mA
Module width: 42HP
Module depth: 25mm

Notes: Four channel voltage controlled Clock Divider/Multiplier with master Tap Tempo. Each channel can be synced to the tap tempo, to the channel above, or to an external clock. Each channel also has a reset jack.

With a Tap Tempo button and five sync'ed clock outputs, the QCD is a versatile head-of-the-chain "Master" clock module, and/or a complex rhythmic pattern generator.

Notes: ***NEW revision TEMPI firmware tempi11 improves External SYNC and RUN/ STOP behaviors. Download here today - http://www.makenoisemusic.com/content/patchsheets/tempi11_firmware_update.zip***

TEMPI is a 6 Channel, polyphonic time-shifting clock module. It provides an intuitive method for creation and recall of complex clocking arrangements within a modular synthesizer system. Using HUMAN and/ or MACHINE programming you could re-create most classic Clock Divider and Multiplier arrangements and then continue on to create new ones. Store up to 64 for later recall and Select them using control signals from within your system or the Select Bus.

Notes: The Shifty is essentially a combination of four sample and hold stages, a sequential gate and sequencer controller. This collection of functions allows for some specific and useful utility application.

One of the primary uses for Shifty is to take a monophonic sequence source and route each new note of the sequence to up to four different synthesizer voices in a specific pattern. In this way you can create pseudo polyphonic sequences since each voice can be triggered to play and sustain while the next voice int the sequence gets triggered. Another term for this is hocketing.

The other main application of the Shifty is to function as an Analog Shift Register. In this mode each new gate input received causes the current set of pitches to be shifted to new output locations as a new one is added and the oldest one is replaced. This can be an interesting way to create chords that are up to four stacked notes when used with a pitch sequence source that has a harmonious series of notes (e.g. a pentatonic scale works really well). Even just using two of the outputs will yield very interesting melodic interplay and is an excellent way to make a simple sequence much more complex and interesting.

In a more basic way the Shifty could be used as a simple Sample/Track and Hold module or as a sequential gate.

Notes: Highly sought-after utility tool that always sells out quickly. Full colour display gives visualisation as an oscilloscope, spectral analyser, spectograph, tuner and more. Waveform and clock generator options too.

Supplier's Notes:
The Ultimate Eurorack Utility Module (and a whole lot more!)

The DATA is a digital platform for testing, measurement, and signal generation in Eurorack modular synthesis systems. It is a modular tool kit, with functions applicable to any system and style.

Use the DATA's scope to view the interactions between your control voltages and audio signals, allowing you to master your modules by understanding their voltage ranges, control shapes, and parameter responses. Use the DATA's dual waveform generator to dial in a precisely scaled LFO for CV control, or use the waveform's frequency "note mode" to effortlessly make dyads (two note chords). Use the DATA's clock program as a master clock or to divide or multiply an incoming clock signal, sending four different clock outs to gate modules directly or as control to sequencers.

The possibilities of the DATA are basically unlimited; with the included microSD you can update the DATA's firmware and we can continue to refine and create new programs.

Notes: The Ultimate Eurorack Utility Module (and a whole lot more!)

The DATA is a digital platform for testing, measurement, and signal generation in Eurorack modular synthesis systems. It is a modular tool kit, with functions applicable to any system and style.

Use the DATA's scope to view the interactions between your control voltages and audio signals, allowing you to master your modules by understanding their voltage ranges, control shapes, and parameter responses. Use the DATA's dual waveform generator to dial in a precisely scaled LFO for CV control, or use the waveform's frequency "note mode" to effortlessly make dyads (two note chords). Use the DATA's clock program as a master clock or to divide or multiply an incoming clock signal, sending four different clock outs to gate modules directly or as control to sequencers.

The possibilities of the DATA are basically unlimited; with the included microSD you can update the DATA's firmware and we can continue to refine and create new programs.

Notes: Steppy is a 4-track programmable gate sequencer with eight internal memory slots, external clocking, numerous tweakable parameters, and a performance-first design aesthetic.

Each track features numerous independent parameters that govern its playback independently of the other tracks. Specifically:

- Each track has its own length, which can range from 1-step to 64-steps, allowing for polyrhythms, fills, or constantly evolving gate interactions between tracks.
- Each track has its own gate length, which ranges from very short to very long, with tied gates possible at the extreme setting.
- Each track has its own clock divider, allowing patterns to play out over completely different periods of time.
- Each track has its own swing setting, which offsets the timing of every other step.
- Each track has its own delay setting, which offsets the timing of every step.
- Each track has its own probability control, which sets the likelihood that each programmed gate will fire when called upon by the pattern.
- Each track can be shifted (or 'rotated') forward or backward by a number of steps. So if you've created a pattern that 'feels' like it has its downbeat on step 3, you can shift that pattern two steps to the left, so that the downbeat sits on step 1.

Tracks can be programmed by entering active steps on the grid or tapped in live as the sequence is moving. Tracks can be selected and modified in real time as the sequence plays. A select button allows you to directly access each track (and each page of 16 steps within that track) directly through Steppy's intuitive multifunction buttons array.

Tracks can be individually muted and unmuted, and a special performance mode (called "Loopy") enables you to touch any two gate steps and instantly create a performance that loops between those steps.

Track patterns can be cleared without clearing its playback parameters, and all track patterns (along with their individual playback and performance parameters) can be saved as a preset to one of eight internal memory slots.

Notes: Maestro is a 6 channel clocked modulation controller inspired by the automation lanes found in digital audio workstation software, brought into eurorack and made playable and performable. Maestro will push and pull the parameters of your other modules with rapid or slowly evolving voltages, always in perfect sync with eachother and the rest of your system.

Details:

20hp

25mm deep

65mA on +12, 18mA on -12, 0mA on 5V

Notes: The SAPEL is a random control voltages source for Eurorack modular systems. It is composed of two main sections, one that generates audio noises, in 4 different versions, and another which includes two specular random clock, random voltages and clock sources.

Noise outputs are colour coded, based on the noise colours, and include:

- Blue (+3dB/oct spectrum)
- White noise (0dB/oct spectrum)
- Pink noise (-3dB/oct spectrum)
- Red noise, a.k.a. Brown or Brownian (-6dB/oct spectrum).

The random voltage and clock section features four uncorrelated random CV generation paths, divided in;

- Fluctuating random voltage;
- Quantized random voltage with 2n stages tuned in semitones referred to 1V/oct scale;
- Quantized random voltage with n+1 stages tuned in octaves referred to 1V/oct scale;
- Non quantized sample & hold.

It is also possible to set a probability distribution with a potentiometer, and apply (or do not apply) the chosen distribution setting to each of the four paths independently.

Furthermore, each of the two random sources section features an independent built-in clock generator, with clock output and random clock output, which can be used in "more than" or "less than" mode. It is possible to use an external clock signal as a clock source, bypassing the built-in one. In addition to that, it is also possible to hand trigger the clock via a manual sample & hold button, which can be also modulated by gate signals.

Notes: Module A-160-5 is a voltage controlled clock multiplier. The incoming clock signal (socket Clock In) is multiplied by a factor that depends upon the control voltage on socket CV In (0...+5V) and the position of the Mode switch. The multiplied clock signal is available at the socket Clock Out. According to the position of the Mode switch different clock multiplying factors are assigned to the control voltage. With 0V CV no clock output is generated. This state is indicated by "all LEDs off". With increasing CV integer factors (left position of the mode switch), power of two factors (middle position) or a mix of both (right position) are obtained. Nine LEDs are used to show the currently selected multiplying factor. In addition two LEDs are used to display the incoming and outgoing clock signal.

A manual control is used to adjust the clock multiplication factor manually without the need of an external control voltage. The voltage generated by this control ("Manual") is normalled to the CV In socket. As long as no plug is inserted into the CV In socket the clock multiplication factor is adjusted by means of the manual control knob and displayed by the LEDs. For dynamic applications (like the ratcheting function described below) the manually generated CV is overwritten by the external CV which has to be fed into the CV In socket.

The module can be used for all kind of clock multiplying applications. One important example is the generation of so-called ratcheting sequences. The band Tangerine Dream is famous for this kind of sequences. A normal sequencer generates only one gate signal per step. A ratcheting sequence may have also more than one gate pulses per step. This function can be obtained by using the A-160-5: one CV output of the sequencer is used to define the number of gate pulses per step. If the control of the step in question is fully CCW the generated CV is 0V and no gate signal is generated (mute of the step). When the control of the step in question is turned clockwise one, two or more gate pulses are generated depending upon the position of the mode switch and the voltage generated by the CV at this step.

Technical note: Due to the nature of clock multiplying it takes a few input clock pulses until the clock output is stable. One has to average a few input clock pulses to generate the multiplied clock output signal. Even when the input clock frequency changes it will take a few cycles until the output clock signal is correct as the module cannot foresee the future of the clock input signal. The generated clock output signal is derived from the last few cycles of the clock input signal. Consequently the module should be driven only by a clock signal with constant or slowly changing frequency.

Notes: Instant IDM! An unusual genre-specific module from Mystic Circuits, automatically generating complex trigger sequences. Create loops or apply real-time effects to a trigger or gate input.

Supplier's Notes:
IDUM is a gate processing effect that turns its input effortlessly into IDM. Making complex electronic music with the modular usually requires meticulous sequencing done in advance or a large ecosystem of modules. Unfortunately, the level of expertise needed to accomplish this is not accessible to the average modular user. IDUM aims to make this process easier and put Intelligent Dance Music, also known as IDM, into the hands of people with average intelligence. IDUM does not require much knowledge to get immediate and compelling results; but with some extra familiarity, this module can enable innovative music making techniques. Instead of generating musical patterns on its own, IDUM acts like an effects processor for the sequences that run through it. For example, a filter or a delay allows the user to alter their sound by twisting the knobs or modulating the parameters. Similarly, IDUM manipulates the actual gates and sequences of connected modules, but with a level of playability normally inaccessible to a sequencer. IDUM can vary carefully crafted sequences or turn your music into an onslaught of controlled chaos. Its open source code and hardware based on the beginner friendly Arduino Nano Every encourage users to tweak their modules to taste or to add new features all while ensuring future improvements as IDUM makes its way into the wild.

IDUM has eight effect modes:

HOLD - Alter the length of incoming triggers.

BURST - Generates a ratcheting effect with timing determined by the clock.

MULTIPLY/DIVIDE - Generates a ratcheting effect with timing determined by incoming triggers.

BALL - Generates a bouncing ball effect.

ROTATE - scrambles the connections of inputs and outputs.

DELAY - postpones incoming gates by a dynamic amount of time based on incoming triggers.

BREAK - preset rhythms that turn incoming triggers into breakbeats.

SKIP - manipulates the clock output to multiply the clock speed or skip forward multiple steps.

In addition to these modes, IDUM features an eight step looper that loops incoming gates as well as any effects that were active on those steps.

To control when IDUM's effects are active, the CHANCE slider sets the likelihood that on a given step an effect will activate and the LENGTH slider sets how many steps the effect will last for. The PARAM knob controls a parameter unique to each effect while the MODE knob selects the mode. All of these controls as well as the LOOP status have their own CV modulation inputs.

Unique to IDUM is its ability to manipulate external sequencers using the clock output. This includes functions like: pausing the clock when an effect is active for dynamic clock division, skipping forwards or multiplying the speed of the clock in SKIP mode, and looping a sub-section of sequencer steps in the looper. To keep everything tamed while manipulating the clock, the CYCLE switch will send out bursts of clocks to catch your sequencer up with its original sequencer position after an effect has completed. Keep in mind that not all sequencers like to be clocked fast enough to work with these features, so for best results pair your IDUM with a TREE/ LEAVES combo from Mystic Circuits.

IDUM might be the stupidest way to make IDM and Mystic Circuits are proud of that. Whether you want to add complexity to your dance floor bangers or make the most obtuse and unlistenable music imaginable, IDUM is here to help. See just how dumb your music can get with the Mystic Circuits IDUM.

Notes: 12HP version of Marbles Random Sampler

Fully calibrated

Notes: Module A-160-2V is an enhanced version of the standard clock divider A-160. The module is a frequency divider for clock/trigger/gate signals, designed to be a source of lower frequencies, particularly for rhythm uses.

The Clock input will take any digital signal from, eg., an LFO, MIDI sync, or the gate from a MIDI-CV interface. At the outputs, you have access to three sets of seven different sub-divided clock signals, from half the clock frequency down to 1/128. The low/high levels of the output signals are 0V and about +10V.

The A-160-2V also has a reset input. Whenever a reset signal is sensed, all outputs are set to certain levels which depend upon the selected mode.

HP : 4

Notes: Complex gate and CV generator designed as a trigger source and modulation tool. Based around four sine wave LFOs that mix together and interact to create ever-changing patterns.

Supplier's Notes:
In 2009 John Berndt coined and defined the term Relabi in his essay "Relabi": Patterns of Self-Erasing Pulse, these are his own words: "Relabi, Def.: The experience of a palpably coordinated plurality of events that appears to be cyclical but simultaneously suspends identification of a uniform pattern, preventing a resolved sense of pulse. Relabi therefore seems equally pulsed and unpulsed at the same time. It is an experiential gestalt, a quality of experience, greater than the sum of its parts (it forms a sustained unity in experience, albeit of a new kind)."

He also makes the question: "Why would anyone want this Relabi experience? I maintain that much of what is exciting in musical forms involves an interplay between the setting up and denying of pulse expectations."

Inspired by this idea, ADDAC System developed this module that is both a gate/trigger and cv generator that can be freely used to trigger events or act as a complex modulation source. Four Sine LFOs are internally generated, each has controls for gain, frequency and mute(off). These 4 LFOs are then mixed together to generate what Berndt named the "Relabi Wave" this "wave" becomes a complex bipolar CV source. This i5v bipolar "wave" can be monitored on the 2 dedicated leds and is also available at its own Output.

Make sure to check the User's Guide for indepth description, working behaviour and diagrams.

Tech Specs:
10HP
4cm deep
100mA +12V
40mA -12V

Notes: The MiniMod Multi Burst Envelopes module generates variable length bursts of repeating envelopes that can change over time, with CV control of all functions.

The BURSTS control selects a "Burst Sequence" of between 1 and 40 individual envelopes. The envelope shape of a burst is chosen with the rotary switch, or it can be varied using an external CV, so that it is even possible to chose a different envelope shape for each individual burst in a sequence.

The width of the envelope (i.e. the attack and decay time) is varied with the P-WIDTH control and this can also be CV controlled as a sequence is progressing, so it is possible to vary the envelope speed of each individual envelope burst while a Burst Sequence is running.

The repeat time of individual bursts in a Burst Sequence is set with the LFO Rate control. The LFO rate can be varied with an external CV as a sequence is progressing, so the gap between envelopes can speed up or slow down over time. An external clock can also time the bursts in a burst sequence instead of, or in addition to the internal LFO. Bursts can also be manually incremented with the CLK push button.

The SLOPE control allows Bursts to start quietly and build in level to maximum, or they can start at full level and then reduce in level as the Burst Sequence progresses. In the centre position all Bursts are of equal level.

Specifications

Module Width: 12hp
Module Depth: 26mm (Including power lead)
Current Usage: 28mA Positive, 12mA Negative
Individual Envelope Length: 20msecs to 2.5 seconds
Internal clock rate: Off, 0.24Hz to 51Hz, or every 4.2 seconds to every 20msecs
Envelope waveshapes: Sine, LogDown, LogUp, ExpoDown, RampUp, Triangle, RampDown, Pulse
Repeats: 1 to 40
Slope: bipolar, sloping up from 4%->100%, and sloping down from 100%->4%

Notes: Amnis is a shift register with a few tricks up its sleeves. It can be used as a generative sequencer for gates and CV, as a tunable digital noise source, as a random gate and CV generator, as the center of a chaotic system and more.

It needs two input signals to start doing its thing. A Clock and some Data. Data can be pretty much any signals. From these two signals Amnis will generate 8 gate outputs, always on the clock. From these gate outputs, it will generate 3 staircase CVs and a slewed CV. With 8 gates and 4 CV outputs it can be the heart of any patch.

Amnis has an XOR input for linear feedback. A shift register with linear feedback is the core of the Rungler, the chaotic core in Rob Hordijk's Benjolin and Blippoo Box. With Amnis you can recreate these type of behaviors with any oscillators you have on hands.

Amnis is compatible with the Turing Machine expanders thanks to its expansion port at the back.

Due to popular demand for a 3U shift register, Amnis replaces (and expands on) Ruissellement, which was the 1U version of this module.

Notes: Brilliantly powerful trigger module, capable of acting as a master clock and a sequencer, generating gate signals and pulses. Good hands-on control options for live performances.

Supplier's Notes:

The Trigger Riot is a multipurpose trigger module that makes ultra complex patterns of gates triggers and clock pulses. The Riot covers a lot of ground in any Eurorack system from the master clocking for your entire system to algorithmic generation of pulses for envelopes, step sequencers, drums and accents that can venture into highly complex territory driven by simple yet powerful logic and algebra with a dash of pseudo randomness for some unpredictable results.

The user interface allows a great deal of control over pulses with each knob acting as a clock divider, clock multiplier, step injector, time shifter, clock shifter, pulse-width modulator, and an arithmetic probability processor. Now take that control and multiply it by 16 and feed it into 8 outputs for maximum Trigger Riot madness!

Furthermore the interface features a master clock knob, push switches to mute unmute and select rows, and multiple switches to configure, adjust, create loops and save your work for later recall from memory banks.

Trigger Riot integrates nicely in the studio with non-volatile memory, generous synchronization options with external gear including sample accurate sync with DAWs, smart synchronization to other Tiptop modules using SyncBus, and DIN Sync for vintage gear. A precise internal tempo clock generator with tap tempo and BeatSync to manage precise changes round out the features.

Notes: This is an exact hardware replica of the Mutable Instruments Marbles.

Notes: The SCM Plus is a clock multiplier with eight gate outputs and complex beat manipulation features. It combines the classic Shuffling Clock Multiplier (SCM) and SCM Breakout (SCMBO) into a single module using higher precision hardware than its predecessors.

Specs:

Electrical and Mechanical Specifications

12HP Eurorack format module
0.95" (24mm) maximum depth (includes power cable)
16-pin Eurorack power header

Power consumption
+12V: 52mA max
-12V: 15mA

Clock Input
2.5V threshold
40kHz maximum

Clock Outputs
12V gate outputs, rise/fall time approximately 1us
40kHz maximum
Jitter (x1 output): max 30us < 120BPM, max 5us >= 120BPM
Latency (clock in to x1 output): 8us worst-case, 3.5us typical

CV Inputs:
Rotate, Slip: Knob attenuates jack signal. Full range: 0V to +3.3V
Shuffle, Skip, PW: Knob offsets jack signal. Full range: -5V to +5V
Gate Inputs:
4x Fast, Mute: 2.5V threshold. Button toggles state.

Notes: Jam Jam is a versatile and fun trigger-and-gate processor with four individually adjustable and CV-able channels. The three modes pack incredible functionality into the tiny 6hp package.

Random mode turns the module into four individually adjustable probability processors, great for adding variety to a patch.

In Clock Phase mode, the module adjusts incoming clock phase based on clock period. Use this to adjust sequencer timing or to create sequences that drift out of sync and then back in with CV.

Use Gate Delay mode as a simple trigger delay to help keep things in sync in your patch or for creative patching: dial in shifts in the timing of events from sub-millisecond adjustments to huge delays of over 15 seconds.

Jam Jam is a musical and fun utility sure to find a use in every patch.

Notes: Skippy is a matrix and non-matrix polyrhythmic sequencer (linear and logarithmic) which offers four completely independent tracks with a very simple interface: one button per track, one function per screen, no sub-menus.

Possible saving of 64 configurations.

Internal connection with expander module (coming soon) and with Zazou, generative composition module (coming end of 2023).

Functions per track

- BPM (10 to 400)
- Number of steps (1 to 64)
- Linear or log
- Random function
- Chaotic function
- Direction: clockwise, counterclockwise, ping-pong, pause
- Number of steps before the start of the sequence
- Number of steps before the end of the sequence
- Gate duration

Specific algorithms

- Euclidean (Bjorklund)
- Matrix Patterns
- microtiming patterns
- matrix rotation

Clock

- External clock input or Reset
- Clock output
- 1/1, 1/4, etc.

Menus

- BPM
- STEP
- BEGIN
- END
- GATES
- PROBA
- CHAOS
- WAY
- SWING
- GAUSS
- EUCLID
- TILES
- POLYR
- JAZZY
- SPIN
- PAUSE
- RESET
- SYS: save, load, new, clk/rst, clk

Tech Specs

Width: 10 HP
Depth: 32 mm

Current Draw:
+12 V 0 mA
-12 V 0 mA

Notes: Keep your patch in sync with Mosaic's compact Clock. Clock is a configurable master clock source with knob and CV control over the clock rate, two range settings, and a pause feature via the Hold button / gate input. Take control of your composition, or just a portion of it, with Clock.

Tech Specs:
Width: 8HP
Depth: 38mm
Front Panel: Intellijel format, Pulp Logic replacement panels available here.

Notes: Running Order is a two track trigger sequencer. It can be a precise master clock or manipulate incoming clock signal and works great in use as a sub-sequencer/divider in your Eurorack environment.

Zero-jitter clock generation: less than 50 microseconds internal clock jitter
101 style 1/16th note input mode (step/rest) with manual or CV controllable amount of triggers repeats when the active trigger step happens
Euclidean mode enabled for each track where we set Euclidean total steps amount in the circle and then amount of triggers happening in that circle.
Per step trigger probability in 101 mode and global probability in Euclidean mode.
Separate synchronization (reset) inputs, sync for track 1 is normalled to sync track 2
Clock divider for incoming external clock allows to quickly obtain various musical divisions on the fly incl. triplets of course, but more importantly tuplets mode allows you to stretch desired amount of triggers happening into a single bar
Separate mute buttons for each track
8 patterns of triggers sequences stored in the module and recalled on the next power up
Available in 3U / 6HP version

Power consumption:
30 mA +12V
10 mA -12V
0 mA 5V

Dimensions
22 HP
26mm deep with power ribbon cable connected

Notes: Running Order is a two track trigger sequencer. It can be a precise master clock or manipulate incoming clock signal and works great in use as a sub-sequencer/divider in your Eurorack environment.

Zero-jitter clock generation: less than 50 microseconds internal clock jitter
101 style 1/16th note input mode (step/rest) with manual or CV controllable amount of triggers repeats when the active trigger step happens
Euclidean mode enabled for each track where we set Euclidean total steps amount in the circle and then amount of triggers happening in that circle.
Per step trigger probability in 101 mode and global probability in Euclidean mode.
Separate synchronization (reset) inputs, sync for track 1 is normalled to sync track 2
Clock divider for incoming external clock allows to quickly obtain various musical divisions on the fly incl. triplets of course, but more importantly tuplets mode allows you to stretch desired amount of triggers happening into a single bar
Separate mute buttons for each track
8 patterns of triggers sequences stored in the module and recalled on the next power up
Available in 3U / 6HP version

Power consumption:
30 mA +12V
10 mA -12V
0 mA 5V

Dimensions:
22 HP
26mm deep with power ribbon cable connected

Notes: dsp.cpoffee's custom everything-including-kitchen-sink dsp development platform.

At the core of this is an Electrosmith Daisy Patch Submodule, combined with a 12-bit 4 channel SPI DAC [DAC7554], and supporting hardware for more IO

Features
- 8x pots normalled to +5V
- 8x CV in breaks normalled connection and pot acts as an attenuator
- 2x gate in
- 2x gate out
- High-fidelity stereo in/out (Daisy Patch Submodule, using an WM8731 codec)
- 2x 12-bit CV out from Daisy Patch Submodule, scaled to -5v to 10v
- 4x 12-bit CV (or lofi audio w/ some hacking) from external DAC7554, scaled to -7v to 7v
- TRS MIDI in/out (in is auto-sensing for type a/b)
- SD card slot
- Expansion header for +5v, +3v3, SPI, UART, I2C, and USB connections

Notes: SkipLog, a probability processor with sequence capturing and looping features, along a range of other versatile functions waiting to be explored.

SkipLog is a 3-channel rhythmic probability processor designed for inventive rhythmic exploration in modular setups. Introduce unpredictable rhythmic possibilitis to your creative flow.
SkipLog's basic operation is simple: when a trigger or gate is received at one of its three channels' inputs, the same channel’s Probability knob allows you to control the likelihood of these triggers or gates reaching the output. This inputs are internally connected .

SkipLog continuously captures the binary outcomes of its use, storing them for potential sequences. Activate the Loop function to break from pattern creation and loop the recorded sequences. Individual Loop Length knobs for each channel allow adjustment of the loop sizefrom 1 to 16 or 32 steps (as selected on the back), providing evolving rhythmic patterns.

To fine-tune your arrangement, SkipLog introduces functions like Mute for real-time channel silencing, Inv for signal inversion, and Choke for establishing channel priorities. Lastly, the G/T (Gate/Trigger) Mode enables users to specify whether the channel output is a gate or a trigger.

Dimensions
8 HP
33 mm deep

Current Draw
100 mA +12V
22 mA -12V