Tags: Switch module

Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in/outputs, and a common out/input. Each time a pulse is received at the trigger input socket, the common out/input is connected to the next in/output. After the fourth in/output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out/input immediately back to the first in/output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LED's indicate the active in/output (ie. the one that is connected to the out/input at any particular time).

Notes: Module A-151 (Quad Sequential Switch) is like an electronic four-position rotary switch.

It includes trigger and reset inputs, four in / outputs, and a common out / input. Each time a pulse is received at the trigger input socket, the common out / input is connected to the next in / output. After the fourth in / output, the next trigger makes it step back to the first again, and so on. A positive pulse at the reset input switches the out / input immediately back to the first in / output (see Fig. 1). Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Four LEDs indicate the active in / output (i.e. the on that is connected to the out / input at any particular time).

Notes: Module A-182-1 is a simple passive multi-connector similar to the multiples modules A-180-1/A-180-2. In contrast to modules A-180-1/2 each socket is equipped with a 3-position switch that allows to connect the corresponding socket to the internal bus #1 (left position), bus #2 (right position) or to turn the socket off (centre position).

Examples:

- All switches in left position or all switches in right position: 8-fold multiple

- Four switches in left position and four switches in right position: two 4-fold multiple

- X switches in left position, Y switches in right position and Z switches in centre position: two separate multiples with some sockets turned off

Notes: The Shifty is essentially a combination of four sample and hold stages, a sequential gate and sequencer controller. This collection of functions allows for some specific and useful utility application.

One of the primary uses for Shifty is to take a monophonic sequence source and route each new note of the sequence to up to four different synthesizer voices in a specific pattern. In this way you can create pseudo polyphonic sequences since each voice can be triggered to play and sustain while the next voice int the sequence gets triggered. Another term for this is hocketing.

The other main application of the Shifty is to function as an Analog Shift Register. In this mode each new gate input received causes the current set of pitches to be shifted to new output locations as a new one is added and the oldest one is replaced. This can be an interesting way to create chords that are up to four stacked notes when used with a pitch sequence source that has a harmonious series of notes (e.g. a pentatonic scale works really well). Even just using two of the outputs will yield very interesting melodic interplay and is an excellent way to make a simple sequence much more complex and interesting.

In a more basic way the Shifty could be used as a simple Sample/Track and Hold module or as a sequential gate.

Notes: AJH Synth have had quite a few customers asking if we can make the gain jumpers on the MiniMod VCF and VCA modules accessible from the front panel, so this 2HP module aims to address this.

The Gain Switch Multi has two switches which connect to the gain jumpers on the VCA and VCF. Switch "up" is the same as having the gain jumper in place, switch "down" is the same as removing the jumper, and gives higher gain.

Using these switches gives a similar effect to the old "headphone out to external input" trick on the original Model D but with a much wider overdrive range, particularly from the VCA.

As an added bonus, AJH Synth have also included a six way passive multi.

Notes: Module A-150-1 (Dual VCS) contains two separate voltage-controlled switches.

Each switch has a control voltage input, a common Out / Input, and two In / Outputs. The switches are bi-directional: they can work in both directions, so can connect one input to either of two outputs, or either of two inputs to one output. Voltages in the range -8V...+8V at the O/I resp. I/O sockets can be processed by the module.

Two LEDs show which in / output is active (i.e. which is connected to the common out / input).

Notes: Module A152 is a very useful switching and T&H module. It combines a voltage addressed 1-to-8 multiplexer and 8 fold T&H that can be used as kind of an analogue shift register too. The active in/output is displayed by a LED. The digital output of the currently addressed step outputs "high". The remaining digital outputs are low.

Instead of voltage control even clock/reset controlled addressing of the active step is possible. The rising edge of each clock signal causes an advance to the next state. The rising edge of the reset signal resets to step 1.

The sum of the voltages coming from the manual Address control and the CV input define the currently addressed step of the 3 sub-devices. If the module is controlled by clock and reset the control voltage has to remain unchanged as the CV control has priority over the clock/reset control (e.g. simply turn the CV control fully counter-clockwise and do not touch the Address control knob).

Sub-device #1 is the bidirectional 8-fold multiplexer (kind of an electronical 8-fold rotary switch). Bidirectional means that it works into both directions like a mechanical rotary switch: the common socket may work as an output that is connected to one of the 8 inputs that are e.g. connected to modulation or audio sources. But the common socket may even function as input. In this case the signal applied to the common socket is output to the currently addressed single socket. The voltage range of the in/outputs to be switched is the full A-100 voltage range -12V....+12V. All A-100 signals can be switched without any restrictions.

Sub-device #2 is the addressed 8-fold T&H. The signal at the common T&H input is connected to the addressed T&H output. As soon as a new output is addressed the last voltage is stored at the output (Track&Hold function). The T&H section of the A-152 allows the emulation of the "toggling T&H" function of the Buchla module 266 "Source of Uncertainty". Only the first two T&H outputs of the A-152 are required for this application. This unit can be used also as kind of an analogue (shift) register. The difference to a "real" analogue shift register is that the sampled output voltages are not shifted to the next output but remain allocated to the same output. But in some cases (e.g. controlling the pitch of 3 VCOs by 3 output voltages of the A-152) the result is the same.

Sub-device #3 is the digital output section. The digital output of the currently addressed turns to "high". All other digital outputs are low. The digital outputs can be used to trigger e.g. envelope generators or to control the reset input in the clocked mode to reduce the number of addressed stages.

Notes: Designed with and for performing artists, Switch 4 delivers a hands-on signal switching and routing solution for your Eurorack modular synthesiser.

Quickly mute audio signals, trigger envelopes live, select modulation sources on the fly... With custom dual-action toggle switches, an intuitive interface and sturdy construction, Switch 4 will prove just as useful on stage as in the studio.

The bottom switching section includes four lever-actuated toggle switches, to make or break the signal path between the inputs and outputs. These switches feature a dual action: latched upwards, momentary downwards.

The four input signals are also sent to the top routing section, where two rotary switches allow you to select the signals to be sent to the matching outputs. Here you'll also find dual-action toggle switches, for added versatility.

Finally, all signal paths are buffered, avoiding signal cuts when shorting a jack during patching or severe loading effects when driving many inputs. The high-end components provide exceptionally low noise and distortion, so Switch 4 can reliably process audio, control voltages and gates/triggers.

Notes: Part of Xaoc's Leibniz subsystem, which processes signals and voltages by manipulating binary 8-bit numbers, the Poczdam allows switching between two data sources.

Supplier's Notes:
Poczdam is a binary data routing solution for the Xaoc Leibniz Subsystem. It facilitates manual and remote switching between two Leibniz data sources, modifying individual bits of the data stream, and re-clocking the data with its onboard voltage-controlled wideband oscillator or any external clock signal. Poczdam is particularly useful within complex Leibniz setups where the user needs to reconfigure the data flow between multiple modules. However, it can also be employed in small creative patches, e.g., for waveform splicing, disrupting rhythmic loops, or generating digital chaos.
To better understand the device and avoid common pitfalls, it is strongly advised to read through the entire user manual before use.

Component of the Leibniz Binary Subsystem
Routing Leibniz data
Reclocking Leibniz data
Additional CV clock generator (up to 2MHz)

6hp, 30mm deep
Current draw: +20mA/-10mA
Reverse power protection

The high quality Coal Mine black panels are available for all Xaoc Devices modules. Sold separately. Ask your favourite retailer.

Drezno is the input/output front-end of the system, consisting of an analogue-to-digital converter (ADC) and a digital-to-analogue converter (DAC), that alone can be used for manipulating analogue signals and voltages based on their binary representation.

Lipsk is a binary logic processing expander module that can flip (invert) individual bits of the digital signal representation. There are more Leibniz Binary Subsystem elements coming, with specialized and advanced sets of features.

Jena is a digital module that may be used as a flexible waveshaper for CV and audio signals, a wavetable oscillator, a Walsh function generator, or a rhythm generator.

Erfurt is a bi-directional digital counter, frequency divider. It has multiple applications: the output of the counter may be used as a phase source driving a digital wavetable, connected to other Leibniz modules it may scan waveshapes in Jena, produce stepped voltages useful for making interesting glissandi with Drezno and any VCO, generate gate patterns animating the spectrum of Odessa harmonic banks, spawn pseudo-chaotic sequences when fed back to Lipsk, etc.

Notes: Focused versatility seems an oxymoron when describing the features that led us to design the Mixwitch.

With only a pinch of mixing, inverting and controlled switching, we brew up a plethora of combinations and uses.

This is voltage processing magic!
The Mixwitch design comes from a frustration with attenuvertors (bipolar attenuators-inverters) whose off (neutral) position is difficult to retrieve, especially in live situations.

We went for a digitally-controlled analog path where polarity inversion would be at the touch of a button. So, the usefulness of attenuating/inverting can be realized by turning the pot down, swiftly pressing the inversion button and reopening the level. The zero level is where you expect it, with the pot full down.

Once we had a clean polarity control, we easily added a mute function offering the benefit of pre- adjusted pot settings ready to be activated at will.

The next step was to bring something extra, useful and creative. There are plenty of analog switches controlled by a clock; but arbitrarily selecting an input with a voltage is less known. Having both control capabilities combined with our specific mixer features creates a unique fusion: welcome to the Mixwitch !

Notes: This module is a 8 ins and 8 outs precision buffered matrix.

Every output has a rotary switch to select an input. You can make the same input go through several outputs but not several inputs go to the same output.

There's also a bicolor led next to every switch for visual info of the signal that is going thru it.

Allows fast patch changes and easy rerouting signals, both audio and cv.

Can be used as a traditional buffered multiple, pretty flexible one: 1 x 8 outs, 2 x 4 outs, 4 x 2 outs or any other combination.

62 mA +12V
65 mA -12V

Notes: 8-input, 8-output sequential/addressable switch with manual, trigger, and CV control, plus three grouping options, multiple switching directions, and randomization.

Vice Virga is an 8-input, 8-output sequential/addressable switch with a plethora of features and extensive patchability. Vice Virga can be configured as a single 8-channel switch, two 4-channel switches, or four 2-channel switches. Equal parts automated patch arranger and performance tool, Vice Virga has loads of switching control options. Whether you want to chain sequencers, swap outputs on an oscillator, remix a trigger pattern, or mix up every connection in a patch just to see what happens, Vice Virga can do it!

Features:

Size and power:
8HP Eurorack
+12v: 40mA
-12v: 20mA
Vice i from Latin for "alternately"

Virga i from Latin for "switch"

"Alternating Switch"

Notes: Looking Glass is an 5 x 5 active patchbay/matrix mixer/switcher for both audio and control voltages. It features:

5 inputs (1 through to 5), each with attenuators
5 inverted outputs (A through to E) which are 180o out of phase with the inputs
5 normal outputs (A through to E) which are in phase with the inputs
A switch matrix of 25 push on/push off switches and LED status indicators
Any of the 5 inputs can be patched to any of the 5 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.

A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.

The attenuators allow you to reduce the volume of an incoming signal. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the attenuators are your on-board way around this.

Specifications:

12V draw: 30mA
5V draw: 0mA
-12V draw: 31mA
Depth: 35mm
Width: 18HP

Notes: Subway is a scanning crossfader with 8 inputs and 1 output.

The eight inputs can be used for control voltages as well as audio signals. A potentiometer or CV can be used to mix between the individual sources. Each of the inputs also has a manual on/off switch.

Application examples

Complex modulations
Waveform selector for oscillators or noise
Morphing waveforms from wavetables
Switching between different envelopes
Controls:

Scan knob - master control over which input goes to the output. The knob is shifted when a CV is applied to the scan CV input.
Enable switch - Controls which input is active. When the LED is off, the input is removed from the output selection. A dim LED means the input is active but not yet selected. Bright LED means that the input is currently being sent to the output.
Curves: Subway has three different curves if you hold down keys 1-3 when switching on and then release them. Button 1 sets a linear curve, button 2 sets an exponential curve and button 3 sets a steady curve.
Power consumption: 80mA at +12V and 22mA at -12V

Depth: 38mm

HP : 6

Notes: Erica Synths Black Mixer is compact, high quality audio mixer with bonus features - mute switch on each input and three buffered outputs. This allows you to add audio signals to your mix instantly and in exactly right level, plus you can send signals to several post-mixer devices simultaneously, for example, split the output signal to LP and HP VCFs and create advanced bandpass and notch filters.

Technical specifications:
Max input level: -10V - +10V
Mixer gain: 1
Power consumption : +8mA, -8mA
Module width: 6HP
Module depth: 25mm

Notes: Dual AB Switch

The A/B Switch selects between A and B and the middle position of the switch is a "mute", works with any kind of signal (cv or audio) and is bidirectional.

This is an utility module that was made for switching stereo signals, but other uses are possible:

Select between 2 stereo sources.

Select between 2 stereo destinations.

Bypass control for mono signal processing.

Routing control for a single signal.

Panel is reversible so it can be mounted with the switches on the right or left.

This module does not draw any power.
Size: 8 HP
12 mm deep

Notes: Flexible Eurorack signal paths under gate or trigger control: that is the basic principle behind Route 4. Consisting of a pair of complementary routing sections, it grants access to a new level of signal routing options.

The module's top section is a 4-to-1 router. Any of the four signal inputs may be selected to be mixed into the section's output, as determined by the control inputs.

Control can either be gate or latch driveniin the latter case, the signal inputs are toggled on and off by received trigger pulses. Meanwhile, the solo/multi switch determines whether the inputs are exclusive, or if multiple may be active at the same time.

With each input socket biased by a +1 V precision voltage source when left unused, gate or trigger controlled transposition of pitch sequences becomes a breeze.

On the bottom, the 1-to-4 router provides the same feature set, with a single input being routed to up to four outputs and normalisation between the sections adding some patching convenience.

All signal paths are designed for use with any Eurorack signals, whether they be control voltages, audio or gate streams. Visual feedback is provided by 10 responsive LEDs, continually displaying the status of the routers.

With Route 4, an 8 HP super-flexible analogue mixing and routing powerhouse has arrived to fuel your patching imagination. The ability to redirect signals within a modular system on the fly, with an unparalleled level of control, is sure to excite even the most seasoned patcher.

8 HP | +12: 35 mA, -12: 20 mA

Notes: Particles, is 4 channels of trigger modulation, capable of mathematically variating and manipulating your patterns with a combination of features to play with.
It can evolve your rhythmic idea into more complex and groovy patterns which are difficult to achieve without music knowledge.

You can create your algorithms from the rhythmic tools provided to be able to change the patterns instantaneously in many ways without worrying to sacrifice
the original idea.

You can shift and scramble the outputs, you can repeat the triggers with different time signatures to transform the grooves, mute in different ways, disappear by probability trigger inputs, disappear by probability repetitions, use sequential switching to shift randomly with a different kind of resetting, bypass each channel and set it individually the amount of each feature per channel when feeding external CV.
The idea of Particles, was designed to provide features for building complex breaks, grooves, organic-evolving percussion sounds, and different options for
arpeggios, and even bass line grooves, the limits are decided by you.

Particles Features

4 trigger inputs/outs.

Repetitions with different distribution times to choose from.

Manually shift the output channels, scramble them randomly or clocked them in forward mode.

Reset the outputs to 4 different shift modes.

Disappear repetitions by probability per channel.

Disappear the input trigger by probability per channel.

Mute each channel with clock divisions from the input clock.

Mute manually the outputs

Disable triplets from repetitions to have musical patterns

Random voltages output clocked from clock input.

The slider keeps the adjusted value from each feature.

Notes: Most musicians use their feet as an extension of their playing, either pushing piano pedals, sustain pedals, guitar pedals.

However, feet have been underrated while using modulars. In the past ADDAC released a series of modules using sustain and expression pedals for triggering or controlling signals to help breaking the ice. While these are small and still useful for simple uses, ADDAC wanted to create something more specific this time.

This new solution features 5 footswitches and 5 inputs for external expression pedals with independent controls for each.

The aim was to save HP rack space and so created an external floor pedal with all the footswitches and controls, keeping the module HP to the minimum possible featuring only the 10 outputs and the connector to the external floor pedal.

There are many expression pedals in the market and although the most common one is the TRS pedal there are 2 other standards: RTS and TS.

All five ADDAC311 inputs expect TRS pedals, if you're looking into buying one choose a TRS pedal.

If you already have other pedals channel 4 features jumpers that can be switched in order to be used with a RTS pedal.

Channel 5 features a jumper that can be switched in order to be used with a TS pedal.

External expression pedals are required for their outputs to work.

External expression pedals are not included

Notes: ADDAC809 is a dynamic CV operated I/O router that allows one source (Audio or CV) to be routed through 2 different chains (of one or more modules) before being sent to an output.
Six routing patterns are allowed:

1. IN > OUT
2. IN > CHAIN A > OUT
3. IN > CHAIN B > OUT
4. IN > CHAIN A > CHAIN B > OUT
5. IN > CHAIN B > CHAIN A > OUT
6. IN > > OUT
A practical example is to have an audio source, a delay and a looper.
And the question: should the delay be placed before or after the looper? Sometimes you may need the delay to be before the looper as you may want to sample the audio with the delay or sample the pure audio source and apply the delay afterwards.
This small utility module solves this issue on the fly without having to repatch anything.

INPUTS & OUTPUTS

TO CHAIN B: Connect to your Chain B input
FROM CHAIN B: Connect to your Chain B output
TO CHAIN A: Connect to your Chain A input
FROM CHAIN A: Connect to your Chain A output
INPUT: Connect to your Input Source
OUTPUT: Connect to your Output Source

ROUTING PATTERNS

There are 2 ways to address the six routing patterns:

Buttons: using the frontpanel push buttons and/or dedicated trigger inputs to latch between 2 states.
BYPASS: Chooses between Pattern 1 and any other pattern
PARALLEL: Chooses between Pattern 6 and any other pattern
ORDER: Chooses the order A before B or B before A
DUAL/SINGLE: Chooses to use a Dual (A>B or B>A) or Single chain (A or B)
CV: The dedicated CV input expects a 0 to +5v input and allows to jump to the precise routing pattern using a specific voltage interval in increments of approx. 0.83V:

Pattern 1: 0v to 0.83v
Pattern 2: 0.83v to 1.66v
Pattern 3: 1.66v to 2.5v
Pattern 4: 2.5v to 3.33V
Pattern 5: 3.33v to 4.16V
Pattern 6: 4.16v to 5V

Tech Specs:

Width: 12 HP
Depth: 55mm
Current: 80mA +12V / 30mA -12V

Notes: Sindikat is made to be placed in the heart of every modular setup: copy, invert, attenuate, scale, get different polarity versions simultaneously of two pair of mixes, mix CV as well as audio (up to 8 sources in total), mute or switch to add desired source to a bigger unity mix, scale two separate mixes with chosen gain.. All circuits can preserve their independent use and/or be combined!

Details & use:

The module consists of circuits designed to group the most useful operations for signal mingling in modular synth setups -but in the more fun manner!

It is designed in the way that the circuits can function independently -be patched to the other modules- or to be combined inside the module at the same time!

On the top of the module there is a buffered multiple (the bi-color led is indicating signal input and its polarity) : Next to the input there are two outputs giving the exact copy of the incoming signal. On the third output you'll get the 'attenuverted" version of that signal which is controllable by the dedicated attenuator/inverter potentiometer.

This signal can be further added (or muted) via its switch, internally to a unity gain mixer situated on the bottom of the module via its SUMM OUT.

This mixer has its own 3 inputs who will accept CVs as well as audio signals with an output gain of 1/3.

Its bi-color led will indicate the polarity of the incoming signals.

In the center of the module there is a CV Processor consisting of two mixers each mixing two signals- in the way that:
The first one takes two signals (A and B) and outputs simultaneously the positive version of their mix (AB+ OUT) and the negative version (AB- OUT).
Their gain is scaled by the potentiometer: going on 1x in the middle position to 2x fully turned. (After middle position with a stronger signal and due to higher gain it will start to saturate producing an distortion-like effect)
Further, via their switch, those mixes also can be added to a unity gain mix (SUMM OUT) and therefore creating a larger mix.
You'll do that by choosing which polarity output you want to send to a summing mix.
In the middle position of the switch the signal is "off" so you can use this to mute/un-mute the signal in the unity mix. Also, even if it is in "off" position this only breaks the internal link to a unity mix but you can still use their distinctive outputs to send your positive and negative mixes elsewhere in your system.

Goes the same for the second one: C and D inputs giving positive (CD+) output result and negative (CD-) simultaneously , all with gain select and the switch choice for summ positive or negative (or none) to a bigger unity mix.

You can also choose to use those two circuits as a simple attenuators for ex. by patching only one signal so you'll get an attenuator and polarizer at once!

The module can process CV and audio as well in every circuit.

Therefore, by summing eventually all the signals to a final "SUMM OUT" output you can create up to 8 sources -in the module- large mix!

Made for more fun with a modular!

This module fits perfectly well with Modulaire Maritime "Decca" switch-based manual control module.

As these modules are developed from practicing recording in "one take" (same for a live performing), combining them you get an extended control over CVs, gates and audio going on in the system, allowing to switch- stop/mute, change polarity, introduce/mix more gates, drums,.. on the fly.

8hp
25mm deep
Reverse voltage protected

Notes: Particles, is 4 channels of trigger modulation, capable of mathematically variating and manipulating your patterns with a combination of features to play with.
It can evolve your rhythmic idea into more complex and groovy patterns which are difficult to achieve without music knowledge.

You can create your algorithms from the rhythmic tools provided to be able to change the patterns instantaneously in many ways without worrying to sacrifice
the original idea.

You can shift and scramble the outputs, you can repeat the triggers with different time signatures to transform the grooves, mute in different ways, disappear by probability trigger inputs, disappear by probability repetitions, use sequential switching to shift randomly with a different kind of resetting, bypass each channel and set it individually the amount of each feature per channel when feeding external CV.
The idea of Particles, was designed to provide features for building complex breaks, grooves, organic-evolving percussion sounds, and different options for
arpeggios, and even bass line grooves, the limits are decided by you.

Particles Features

4 trigger inputs/outs.

Repetitions with different distribution times to choose from.

Manually shift the output channels, scramble them randomly or clocked them in forward mode.

Reset the outputs to 4 different shift modes.

Disappear repetitions by probability per channel.

Disappear the input trigger by probability per channel.

Mute each channel with clock divisions from the input clock.

Mute manually the outputs

Disable triplets from repetitions to have musical patterns

Random voltages output clocked from clock input.

The slider keeps the adjusted value from each feature.

Notes: Switchy is a module that allows you to turn on or off up to three modules (or busboard) independently of each other.

No need to turn off the whole case: All three voltages (+12V, -12V, 5V) are interrupted at the same time.

Used to reduce the background noise of certain "noisy" digital modules when not in use, to initialize certain modules or change their function, to change an SD card, to relieve the power supply with energy-consuming modules, etc.

Dimensions
6 HP
30 mm deep

Current Draw
20 mA +12V
20 mA -12V
20 mA 5V

Notes: The 1F is a voltage controlled switch, intended to be 'one friend' for your sequencer. Its design has been specially focused on working with sequences, by giving them some randomness, applying transpositions or constant variation over time. For this, 0.1% tolerance resistors have been used to achieve exact unitary gains for precision summing of the v/oct signals. More detailed info on the demo video.

Technical specifications:

4HP.

27 mm depth.

Consumption: 15mA +12V; 10mA -12V

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this version is the latching model (stays on or off after pressing). In fact, it works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP

Notes: Bartender? The power of gate signals at the touch of a button, please - but make mine a narrow one!

You already know what this is: it's a gate signal generator, and it generates gate signals. That's all there is to it. You press the button, the LED indicator lights up, and you get a 5v gate signal! Brilliant!

You get three, in just 2hp! That's 1 1/2 gate signal generators per hp! That's more than [competing product] from [competing brand]! You knew you made a good decision when you decided to look at this product.

All that remains now is to open your heart, and your wallet. Buy this gate generator - this is the momentary model (is normally off, and temporarily on when you press it). In fact, this also works really well with the Quad Gate to Trigger Converter, also from Herzlich Labs - now you can generate both gates and triggers with ease! And in such little hp!

Oh, one more thing? Your friends are going to be very envious of this, when you show it off. Gold plated nuts, gold plated front panel, tastefully matte indicator LEDs, pleasantly tactile buttons, black hardware. All the details have received the closest care and attention.

Dimensions: 2 HP