Intellijel

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: Blank panels for Intellijel 1U spaces. Made from high quality brushed aluminum that matches the 1U modules.

These can also be used for DIY purposes if you drill / mill them to fit your own custom circuits.

Notes: Blank panel for Intellijel 1U spaces. Made from high quality brushed aluminium that matches the 1U modules.

These can also be used for DIY purposes if you drill/mill them to fit your own custom circuits.

Comes with 2 screws.

Notes: Blank panels for Intellijel 1U spaces. Made from high quality brushed aluminum that matches the 1U modules.

These can also be used for DIY purposes if you drill / mill them to fit your own custom circuits.

Notes: Blank panels for Intellijel 1U spaces. Made from high quality brushed aluminum that matches the 1U modules.

These can also be used for DIY purposes if you drill / mill them to fit your own custom circuits.

Notes: Blank panels for Intellijel 1U spaces. Made from high quality brushed aluminum that matches the 1U modules.

These can also be used for DIY purposes if you drill / mill them to fit your own custom circuits.

Notes: 3.5mm Patch Cables - 5 PACK Assorted Colors 36" (90cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colors:

RED
GREEN
YELLOW
GREY
BLUE

Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 12" (30cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE

Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 24" (60cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE

Notes: 3.5mm Patch Cables - 5 PAK Assorted Colours 6" (15cm)

Excellent quality patch cables for use with Eurorack modules.

Made by AdInfinitum.

Included colours:
RED
GREEN
YELLOW
GREY
BLUE

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: 4U x 104HP Gig Bag (For Palette)

Clearance to leave your system patched and with a Palette 104 Decksaver Lid attached

Padded main compartment protects your case from bumps and scratches

Waterproof zippers

Zipped outer pocket for stuffing accessories and other gear

The rear pocket closes with velcro at the top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.

Super beefy strap connectors with clipped strap

Padded Handle

Lightweight

Notes: The Transporter

High quality and durable padded gig bags for transporting your precious modular synth cargo- don't worry, there is enough head room to leave your system patched.

Travel First Class

Very high quality and durable padded gig bags for transporting your precious modular synth cargo. Sized for our 4U Palette Cases.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: The new, 2nd generation Audio Jacks Board comes pre-installed in every Intellijel 7U case manufactured since early 2019. Because this board is more fully featured than the previous generation, it's available as a stand-alone component for anyone who wishes to update an older 7U case.

You can tell which board you have by looking at the connectors. The new Audio Jacks Board has a large shrouded header flanked by two smaller shrouded headers, flanked by two link connectors at either end. Older boards have only one connector along the bottom edge.

The board holds four Neutrik TRS jacks, each of which can be configured as either an input or an output depending on the modules you connect. This allows you maximum flexibility when configuring your case - whether you wish to use the audio jacks as outputs, inputs, sends & returns; or some combination of these.

The jacks carry different audio signals depending on what you connect to the Audio Jacks Board. Please refer to the manual for more details on the many options available.

Notes: 7U x 104HP Gig Bag

Sized to perfectly fit the 7U x 104HP Performance Cases.

The padded main compartment protects your case from bumps and scratches

Waterproof zippers

Outer pocket for stuffing accessories and other gear (great for adding the Intellijel Pouch filled with cables and hubs)

The rear pocket closes with velcro at top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.

Rugged strap connectors with clipped strap

Carry handles

Lightweight

Notes: 7U x 84HP Gig Bag

Sized to perfectly fit the 7U x 84HP Performance Cases.

The padded main compartment protects your case from bumps and scratches

Waterproof zippers

Outer pocket for stuffing accessories and other gear (great for adding the Intellijel Pouch filled with cables and hubs)

The rear pocket closes with velcro at top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.

Rugged strap connectors with clipped strap

Carry handles

Lightweight

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: A high-quality, custom Eurorack patch cable and bundled them in handy packs of four (4).

Instead of rainbow packs, each colour will be linked to a specific size, offering extra convenience for patching and sorting cable lengths.

Each pack of four comes with a custom velcro cable tie and is attached to a cardboard display hangar, in an effort to reduce plastic packaging where possible.

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Get Amped

Amps comprises two precision linear VCAs that have been carefully designed to offer a wealth of flexibility and additional functionality. The front panel controls and signal normals allow these two VCAs to also be configured to function as: line level boosters, crossfaders, ring modulators, mixers, and much more. They can also be chained together by way of an included cable to form larger, more complex systems.

Amps features cascaded CV inputs and cascaded mix outputs allowing it to be used in a number of versatile configurations. A boost switch enables you to amplify each VCA's input by either +6dB or +20dB i ideal for boosting low amplitude signals or pleasingly overdriving audio. The addition of a phase inversion switch for the second channel allows Amps to function as a ring modulator. The CV normalization, which can also be inverted and offset, also allows for VC-Crossfader functionality.

Features

Manual LEVEL slider per VCA i convenient when using the module as a mixer, or for biasing the signal for CV (such as when modulating the VCA with a bipolar LFO).
Dedicated CV attenuators with dual color LEDs for monitoring bipolar CV signals.
Linear response curve.
Input and CV normalling of VCA A to VCA B to allow a single source to feed and/or control both VCAs.
Output normalling of VCA A to VCA B to allow both VCAs to feed a single output.
Each VCA has a boost switch that can increase the output level by either +6dB or +20dB.
Phase Invert switch on VCA B allows for ring modulation capabilities.
CV Invert switch on both VCAs allows for crossfading one signal into another.
4-pin link connectors on the rear panel allow for multiple AMPS modules to be chained together to create a 4-channel mixer; 6-channel mixer; etc.

Dimensions
6 HP
36 mm deep

Current Draw
40 mA +12V
46 mA -12V

Notes: Get Amped

Amps comprises two precision linear VCAs that have been carefully designed to offer a wealth of flexibility and additional functionality. The front panel controls and signal normals allow these two VCAs to also be configured to function as: line level boosters, crossfaders, ring modulators, mixers, and much more. They can also be chained together by way of an included cable to form larger, more complex systems.

Amps features cascaded CV inputs and cascaded mix outputs allowing it to be used in a number of versatile configurations. A boost switch enables you to amplify each VCA's input by either +6dB or +20dB i ideal for boosting low amplitude signals or pleasingly overdriving audio. The addition of a phase inversion switch for the second channel allows Amps to function as a ring modulator. The CV normalization, which can also be inverted and offset, also allows for VC-Crossfader functionality.

Features

Manual LEVEL slider per VCA i convenient when using the module as a mixer, or for biasing the signal for CV (such as when modulating the VCA with a bipolar LFO).
Dedicated CV attenuators with dual color LEDs for monitoring bipolar CV signals.
Linear response curve.
Input and CV normalling of VCA A to VCA B to allow a single source to feed and/or control both VCAs.
Output normalling of VCA A to VCA B to allow both VCAs to feed a single output.
Each VCA has a boost switch that can increase the output level by either +6dB or +20dB.
Phase Invert switch on VCA B allows for ring modulation capabilities.
CV Invert switch on both VCAs allows for crossfading one signal into another.
4-pin link connectors on the rear panel allow for multiple AMPS modules to be chained together to create a 4-channel mixer; 6-channel mixer; etc.

Dimensions
6 HP
36 mm deep

Current Draw
40 mA +12V
46 mA -12V

Notes: The Atlantis is heavily inspired by the architecture and sound of the classic Roland SH-101. It has always been one of our favorite synths and we really liked how the seemingly limited architecture allowed for all sorts of creative and musically useful sounds to be easily generated.

Just like the 101 it is quick to dial in beautifully rich bass and lead sounds. However this module uses triangle core VCOs (based on the Dixie core) instead of Saw core which respond much more musically to FM. The modulation oscillator can be used as an LFO or VCO (audio rate) and both track very precisely over 8 or more octaves.

In the mixer section you can adjust the balance of the primary oscillators waveforms including a sinewave which is normalled to the EXT IN jack. You could also patch in one of the modulation oscillators waveforms into this channel and be able to operate the Atlantis as a proper two oscillator synth. There is a switch labelled "LINK" which enables the modulation vco pitch to be based as an offset of the primary VCO. This is useful when using it as a stacked dual vco or when you have the mod VCO acting as the linear FM source for the primary vco and wish to maintain the ratio.

The filter section is a Roland style cascaded 4 pole multimode filter with LP, BP and HP modes. The LP Boost switch engages a special mode useful for the LP that produces a much fatter and prominent sound that is not drowned out by resonance (unlike the original SH-101). The filter self-oscillates to produce a very clean sine wave which also tracks 1V/Oct. Between the Mod VCO, Primary VCO, Sub Oscillator and resonating filter it is possible to layer up to four different pitches at one time.

The envelope section is an ADSR with a dual range switch. It also can be set to a looping mode which can be gated on/off externally.

The output VCA feeds into a two level output clipping circuit that you can use to get a much ballsier/dirtier sound.

Notes: Updated Atlantix module is an even better synth voice than the original Atlantis. Based on the Roland SH-101 formula, it's a monster with dual VCOs, legendary filter and built-in envelope generator. All you need for iconic analogue sounds.

Supplier's Notes:
Atlantix

Dual Oscillator Subtractive Analogue Synth Voice

It's Massive

The Atlantix is a complete analogue synth voice. It's quick to dial in huge bass or lead sounds, and easy to push it into new sonic territory. Dual VCOs, Multimode VCF, VCA with Drive, and an ADSR envelope; all of the building blocks needed to expand or start making sound in your rack. With 32 patch points and a selection of routing switches, you can remix these blocks into something all your own.

Reimagining a Reimagined Classic

The Atlantix is the highly-anticipated successor to the Intellijel Atlantis which was originally inspired by the classic Roland SH-101. Despite the SH-101's seemingly limited architecture, it produces various creative and musically useful sounds that have inspired generations of artists and countless hits. The Atlantix is just as immediate for dialling in beautifully rich bass and lead sounds. The thoughtful design, numerous additional features, and flexible patching options open up a massive amount of new sonic territory to explore as well.

The Atlantix is an analogue, complete subtractive synthesizer voice condensed into a single 42HP module. It provides all the fundamental building blocks needed to make sounds in Eurorack: VCOs, VCF, VCA, S&H, Noise, and an Envelope.

Oscillators - Advanced TZFM and Flexible Mixer

The Atlantix uses two triangle core voltage controlled oscillators (VCO) which respond in a musically pleasing way to frequency modulation. The Atlantix primary VCO (VCO A) is capable of thru-zero frequency modulation and has a dedicated amplifier for controlling FM depth (FM INDEX). The modulation oscillator (VCO B) can be used as either an LFO or VCO. The highly flexible architecture allows you to route VCO B as a modulation source or stack it as a secondary VCO all by the flick of a switch or slider. VCO B also has a bonus "spike" waveform output which is a square wave with fixed HPF, similar to the Buchla Easel. Both oscillators track very precisely over eight or more octaves.

In the mixer section, you can adjust the balance of the primary oscillator's waveforms, sub-oscillator noise, and two auxiliary inputs that are normalled to additional VCO A waveforms or VCO B waveforms. The auxiliary inputs also allow you to patch other external signals into the mix.
The second Auxiliary input has a switch that allows you to route the source between the mixer sum or directly into the VCA (post-VCF). The latter is a way to pass an unfiltered fundamental signal to the final VCA stage and then blend it with filtered audio from the VCF. This draws inspiration from the architecture of the CS-80 where a sine wave is mixed with the filtered audio to make glassy tones with some added harmonics.

Multimode Filter - From Drips to Growls

The filter section (VCF) is a discrete cascaded 4-pole multimode filter with lowpass, bandpass, highpass, and phaser (multi-notch) modes. The filter can self-oscillate which produces a very clean sine wave that also tracks 1V/Oct. The VCF has three frequency modulation sources, two of which are normalled to the external pitch and envelope and have switches for polarity.

Add Atlx for dedicated outputs from each mode.

Envelope - A Classic ADSR

The envelope section is an analogue ADSR with three timing ranges: slow, medium, and fast. It can be gated externally or via a manual gate button located in the centre of the panel. The ADSR is routed through a VCA which can be used for level or velocity control.

Modulation - Random, Feedback, and Built-in Routing

Two eight-position rotary switches allow you to select from eight different modulation sources and route them to outputs MOD X and MOD Y. Each switch also has a polarity control and an option to level shift between unipolar and bipolar operation. MOD X is normalled to VCO A frequency modulation and MOD Y is normalled to VCF frequency modulation. The dedicated outputs allow for further creative modulation patching.

Four of the Input jacks have normal switches to change your patch without the need for cables.

The analogue Sample and Hold (S&H) circuit is normalled to the white noise source and can be clocked by VCO B, an external clock source, or via the gate input for per-note synced randomization.

Atlx - Expander w/ Ring Mod (Optional) ***Sold separately ***

The Atlx expander provides 16 additional jacks to the Atlantix, including: dedicated waveform outputs for A and B oscillators, filter outputs, and a ring modulator. Atlx adds many new possibilities for self-patching, advanced routing, and connections to other modules.

Specs + Downloads

Width: 42HP
Depth: 25mm
Power: 140mA @ +12V
138mA @ -12V

Notes: Intellijel have created a 1U version of the handy Atlantix Expander. It is exactly like the 3U version but arranged to fit in a 1U space. Comes with a cable for connecting to the Atlantix.

Notes: Patching Heaven

Adds 14 dedicated outputs and a Ring Mod to the already powerful Atlantix module.

The Atlx expander provides 16 additional jacks to the Atlantix, including: dedicated waveform outputs for A and B oscillators, filter outputs, and a ring modulator. Atlx adds many new possibilities for self-patching, advanced routing and connections to other modules.

Filter Outs

Lowpass
Highpass
Bandpass
Phazor

Ring Mod

X In
Y In
RING Out

Oscillators A/B Outs

Sine
Triangle
Saw
Square (w/ PWM on A)
Sub Square (A only)

Notes: Att 1U Passive Variable Signal Attenuator

This passive attenuator has a 100K linear potentiometer that is DC coupled. Perfect for adding attenuators to those 1U/3U modules without.

Width: 6HP
Depth: 18mm

Notes: ***B-STOCK: Box opened, but product is in excellent condition and in perfect working order***


Dual Balanced ins and outs for the studio or the road. Interface your rack with the balanced line level world; send and return to pedals or desktop FX units; patch in and out of your DAW, external synths, drum machines and other line-level instruments.

Get Connected

Audio I/O (2023 edition) allows you to effectively interface your Eurorack modular system to the balanced line-level world (+4 dBu). You can send and return to rack mount/desktop fx units, patch to external line-level instruments like synths and drum machines, interface to a DAW and much more.

The 2023 edition moves the TRS jacks to the top of the panel

The rear-mounted 3-pin CHAIN IN connector allows you to sum (in parallel) other audio sources to go from Eurorack level to the BAL LINE OUTPUTS. This could be from modules like the Mixup 3U, Xfade 1U, Stereo Mix 1U, and XY I/O 1U. You could also use this to connect with the 3-pin headers on the Palette and 7U cases audio i/o boards.

The rear-mounted 3-pin CHAIN OUT connector allows you to directly connect the level-shifted BAL LINE IN to the inputs of other compatible devices such as the Mixup 3U, Outs 3U, Stereo Mix 1U, XY IO 1U, and Headphones v2 1U. You could also connect the to the TRS jacks of the Palette and 7U cases audio i/o boards.

Features:

2 x Balanced TRS 1/4" to Eurorack modular level input paths
2 x Eurorack modular level signals to Balanced TRS 1/4" output paths
4 x six stage analog led VU meter to monitor all inputs and outputs simultaneously
Input path has up to 20 dB of gain, which allows you to patch in low-level consumer level signals and boost them.
Output path steps a nominal Eurorack level (10 Vpp) down to +4 dBu with up to +6 dB gain
3pin CHAIN IN connector
3-pin CHAIN OUT connector

Dimensions
10 HP
39 mm deep

Current Draw
75 mA +12V
70 mA -12V

Notes: Dual Balanced ins and outs for the studio or the road. Interface your rack with the balanced line level world; send and return to pedals or desktop FX units; patch in and out of your DAW, external synths, drum machines and other line-level instruments.

Get Connected

Audio I/O (2023 edition) allows you to effectively interface your Eurorack modular system to the balanced line-level world (+4 dBu). You can send and return to rack mount/desktop fx units, patch to external line-level instruments like synths and drum machines, interface to a DAW and much more.

The 2023 edition moves the TRS jacks to the top of the panel

The rear-mounted 3-pin CHAIN IN connector allows you to sum (in parallel) other audio sources to go from Eurorack level to the BAL LINE OUTPUTS. This could be from modules like the Mixup 3U, Xfade 1U, Stereo Mix 1U, and XY I/O 1U. You could also use this to connect with the 3-pin headers on the Palette and 7U cases audio i/o boards.

The rear-mounted 3-pin CHAIN OUT connector allows you to directly connect the level-shifted BAL LINE IN to the inputs of other compatible devices such as the Mixup 3U, Outs 3U, Stereo Mix 1U, XY IO 1U, and Headphones v2 1U. You could also connect the to the TRS jacks of the Palette and 7U cases audio i/o boards.

Features:

2 x Balanced TRS 1/4" to Eurorack modular level input paths
2 x Eurorack modular level signals to Balanced TRS 1/4" output paths
4 x six stage analog led VU meter to monitor all inputs and outputs simultaneously
Input path has up to 20 dB of gain, which allows you to patch in low-level consumer level signals and boost them.
Output path steps a nominal Eurorack level (10 Vpp) down to +4 dBu with up to +6 dB gain
3pin CHAIN IN connector
3-pin CHAIN OUT connector

Dimensions
10 HP
39 mm deep

Current Draw
75 mA +12V
70 mA -12V

Notes: The aux mix 1U is a 3-channel stereo mixer module with a stereo auxiliary send bus. The routing options on this mixer module make using aux mix 1U for send FX, parallel processing, feedback mixing, and more possible. It is designed for audio signals only (not for mixing CV). It is AC-coupled, and uses audio-grade, logarithmic attenuators for a smooth, even response across the entire volume range.

Each channel has a dedicated pair of inputs for stereo audio sources. The left channel inputs are normalled to the right for mono audio sources. All three channels feature a precise level attenuator, a mute switch, and an LED input activity level indicator. The three stereo channels are mixed and summed to the main outputs, where they can be patched out to a wider Eurorack system or external pro-audio equipment. The output stage features soft-clipping diodes for smoother saturation when signal levels are very high.

In addition to the main mix controls, channels 1 & 2 also feature an aux level attenuator with a pre/post switch. These can be used to create an independent aux mix which is routed to another pair of outputs, separate from the main mix. The aux output stage also features the same soft-clipping diodes as the main output. aux mix 1U has four 3-pin connectors on the rear side for directly routing audio between other Intellijel cases & modules - without the need for patching cables. Connections include aux in, aux out, chain in & chain out. This also allows you to chain multiple aux mix 1U modules together to form even bigger mix chains.

Notes: Dual-channel wavefolding with a lot of creative power. Buchla- and Serge-style circuits combine with a voltage-controlled crossfader, allowing you to shape and sculpt sounds in intriguing ways.

Supplier's Notes:

Bifold is a unique dual channel wavefolder with numerous feedback and routing options along with CV control. Mix, blend and crossfade the two different folder flavours into a rich stew of unique waveforms and harmonic movement. It is the first wavefolder to offer simultaneous, independently controllable serial and parallel folder circuits.

Wavefolding is one of the most powerful ways to produce complex timbres out of a simple sound source or waveform. When done well, the results can be warm, textured, organic and full of musical character. Intellijel studied some of the most revered wavefolding circuits and looked at ways to integrate the positive qualities of these into a design that was full of sweet spots and allowed for a huge amount of experimentation and modulation.

Bifold combines two unique wavefolders with a crossfader; One channel (the P channel) has a sonic characteristic inspired by the Buchla-style Parallel "deadband" folding circuit, while the other channel (the S channel) is more characteristic of a Serge-type Serial folding circuit. There are distinct differences to how they react to specific waveforms, modulation and even their overall frequency response. By linking both folders together with a voltage controlled crossfader we further expand the ability to blend these two different folders together to create new waveforms. But this just scratches the surface of possibilities. Ring modulation, blending, crossfading, complex noise generation, feedback modulation, cascaded folding and so much more are all possible thanks to the strategically placed routing switches, jack normals and attenuators and other control options. This is a module that invites much exploration and discovery and pairs well with almost any kind of modulation and sound source.

Width: 8HP
Depth: 38mm
Power: 94mA @ +12V, 94mA @ -12V

Notes: Dual 1 x 4 buffered mult (one audio or cv signal in with multiple buffered outputs).

The output of the first mult is normalled to the input of the second mult to create a 1×8 buffered mult.

Notes: Dual 1 x 3 buffered mult (one audio or cv signal in with multiple buffered outputs).

The output of the first mult is normalled to the input of the second mult to create a 1×6 buffered mult

Notes: We created this new design in celebration of Intellijel’s 5th birthday. 5 cables for 5 years.

This is a four color screen print on American Apparel Jersey t-shirt (%100 cotton).

Notes: We created this new design in celebration of Intellijel’s 5th birthday. 5 cables for 5 years.

This is a four color screen print on American Apparel Jersey t-shirt (%100 cotton).

Notes: We created this new design in celebration of Intellijel’s 5th birthday. 5 cables for 5 years.

This is a four color screen print on American Apparel Jersey t-shirt (%100 cotton).

Notes: We created this new design in celebration of Intellijel’s 5th birthday. 5 cables for 5 years.

This is a four color screen print on American Apparel Jersey t-shirt (%100 cotton).

Notes: Holds everything you need

Very high-quality and durable padded gig bags for transporting your semi-modular synth cargo. Sized specifically for Cascadia.

The padded main compartment protects your case from bumps and scratches.
Zipped outer pocket for stuffing accessories and other gear.
The rear pocket closes with velcro at the top but unzips at the bottom to become a handle sheath so your case can sit on top of a rolling suitcase.
Super beefy strap connectors with clipped strap.
Lightweight with a single-handle design